《BS-ISO-11901-1-2003.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-11901-1-2003.pdf（20页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 11901-1:2003 Tools for pressing Gas springs Part 1: General specifications ICS 25.120.10 ? Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 11901-1:2003 This British Standard was published under the authority of
2、 the Standards Policy and Strategy Committee on 22 December 2003 BSI 22 December 2003 ISBN 0 580 43119 3 National foreword This British Standard reproduces verbatim ISO 11901-1:2003 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Comm
3、ittee MTE/12, Tools for pressing and moulding, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be fou
4、nd in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are resp
5、onsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep
6、the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a blank page, pages 1 to 11 and a back cover. The BSI copyright notice d
7、isplayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 11901-1:2003(E) INTERNATIONAL STANDARD ISO
8、11901-1 Second edition 2003-12-01 Tools for pressing Gas springs Part 1: General specifications Outillage de presse Ressorts gaz Partie 1: Spcifications gnrales BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii BS ISO 119
9、011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iii Contents Page Forewordiv Introduction v 1 Scope1 2 Normative references .1 3 Description and terminology .2 4 Interchangeability dimensions and characteristics 3 4.1 General nomina
10、l specifications.3 4.2 Gas springs of type 900 and 2 0003 4.3 Gas springs of type 1 500 and 2 500.3 4.4 Gas springs of type 5 000 to 7 5003 4.5 Gas springs of type 15 000 to 100 0003 5 Marking.9 6 Technical delivery conditions9 7 Designation10 Bibliography .11 BS ISO 119011:2003 Licensed Copy: sheff
11、ieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried ou
12、t through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO co
13、llaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International
14、Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the element
15、s of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11901-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition cancels and replace
16、s the first edition (ISO 11901-1:1995), Clauses 4 and 5 of which have been technically revised. ISO 11901 consists of the following parts, under the general title Tools for pressing Gas springs: Part 1: General specifications Part 2: Specification of accessories BS ISO 119011:2003 Licensed Copy: she
17、ffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI v Introduction The attention of the user of ISO 11901 is drawn to the fact that gas springs will have to conform to the national regulations of the user country. BS ISO 119011:2003 Licensed Copy: sheffieldun she
18、ffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 1 Tools for pressing Gas springs Part 1: General specifications 1 Scope This part of ISO 11901 specifies the dimensi
19、ons, in millimetres, nominal initial forces and type of gas springs. It applies to gas springs of type 900 to 100 000, pressurized with nitrogen with a nominal initial force of between 900 N 5 % and 100 600 N 5 %, for use in press tools. It also specifies marking, technical delivery conditions and d
20、esignation. NOTE Specifications of mounting accessories for gas springs are given in ISO 11901-2. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest
21、 edition of the referenced document (including any amendments) applies. ISO 7-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tole
22、rance indications BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 3 Description and terminology See Figure 1. Key 1 rod 2 positive stop 3 valve a Pressure filling inlet. b Force. c Nitrogen. Figure 1 Terminology The gas
23、spring is an autonomous spring pressurized with nitrogen. At rest position, the rod is pushed out. This gas spring feature has a gas inlet for pressurization or depressurization. The inlet is located on the casing or on the bottom and is capped. For gas spring of type 1 500 and 2 500, the pressure f
24、illing inlet may be located at the end of the rod. In this case, the rod end is not spherical. The pressure filling inlet of gas springs of type of at least 2 500 includes a pipe thread ISO 7 - Rp 1/8 in accordance with ISO 7-1, and the pressure filling inlet of gas springs of type equal or less tha
25、n 2 500 includes an M6 thread. BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 3 4 Interchangeability dimensions and characteristics 4.1 General nominal specifications See Table 1 Table 1 General nominal specifications Typ
26、e Nominal initial force N Maximum filling pressure MPa End of stroke nominal force increase coefficient 900 900 18 1,5 1 500 1 700 15 1,3 2 000 2 000 18 1,5 2 500 2 600 1,3 5 000 4 700 7 500 7 400 15 000 15 000 30 000 30 000 50 000 50 000 75 000 75 000 100 000 100 600 5 % 15 1,5 4.2 Gas springs of t
27、ype 900 and 2 000 See Figure 2 and Table 2 4.3 Gas springs of type 1 500 and 2 500 See Figure 3 and Table 3. 4.4 Gas springs of type 5 000 to 7 500 See Figure 4 and Table 3. 4.5 Gas springs of type 15 000 to 100 000 See Figure 5 and Table 3. BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun,
28、 na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 General tolerance: ISO 2768-m a Pressure filling inlet (F = located on the bottom, C = located on the casing). Figure 2 Gas springs of type 900 and 2 000 Table 2 Dimensions of gas springs of type 900 and 2 000 Maximum filling pres
29、sure 18 Mpa Type Nominal stroke a L 0,25 l1 1 0 + l6 1 0 + r d D 0,3 D1 0 0,1 15 72 25 92 38 118 50 142 63 172 900 80 205 1 8 19 17 15 72 25 92 38 118 50 142 63 172 80 205 100 245 2 000 125 295 1 16 1 12 25 23 BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:
30、00 2006, Uncontrolled Copy, (c) BSI 5 General tolerance: ISO 2768-m a Pressure filling inlet (F = located on the bottom, B = located at rod end). Figure 3 Gas springs of type 1 500 and 2 500 BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontroll
31、ed Copy, (c) BSI 6 General tolerance: ISO 2768-m a Pressure filling inlet. NOTE As an alternative, the rod end may be flat. Figure 4 Gas springs of type 5 000 to 7 500 BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 7 Gene
32、ral tolerance: ISO 2768-m a Pressure filling inlet. NOTE As an alternative, the rod end may be flat. Figure 5 Gas springs of type 15 000 to 100 000 BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 8 Table 3 Dimensions of ga
33、s springs of type 1 500 and of type 2 500 to 100 000 Maximum filling pressure15 MPa Type Nominal stroke a L 0,25 l1 l2 min l3 0,15 0 + l4 min l5 min l6 r d D 0,3 D1 0 0,1 d1 D2 Number of holes 10 70 16 82 25 100 50 150 1 500 80 210 2 3,5 4 2,5 10,51 12 32 30 10 70 16 82 25 100 50 150 2 500 80 210 2
34、3,5 4 2,5 10,51 15 38 36 25 135 50 185 5 000 80 245 2 3,5 4 2,5 13 14,51 20 45 43 M8 20 2 25 145 50 195 80 255 100 295 125 345 7 500 160 415 3 5 8 3,5 13 14,52 25 50 46 M8 20 2 25 160 50 210 80 270 100 310 125 360 15 000 160 430 3 5 8 4 13 18 2,5 36 75 70 M8 40 4 25 170 50 220 80 280 100 320 125 370
35、 30 000 160 440 3 5 8 4 13 21 2,5 50 95 90 M8 60 4 25 190 50 240 80 300 100 340 125 390 50 000 160 460 3 5 8 4 16 22,52,5 65 120 115 M10 80 4 BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 9 Table 2 (continued) Type Nomin
36、al stroke a L 0,25 l1 l2 min l3 0,15 0 + l4 min l5 min l6 r d D 0,3 D1 0 0,1 d1 D2 Number of holes 25 205 50 255 80 315 100 355 125 405 75 000 160 475 3 5 8 4 16 24,52,5 80 150 145 M10 100 4 50 260 80 320 100 360 125 410 160 480 200 560 250 660 100 000 300 760 3 8 8 4 16 30,52,5 95 195 190 M12 120 4
37、 5 Marking Gas springs shall be labelled in an indelible way, with at least the following information: a) the manufacturers name; b) the gas used; c) the date of manufacture; d) the maximum filling pressure; e) the type. 6 Technical delivery conditions Gas springs shall be supplied at the nominal pr
38、essure at a reference temperature of 20 C. NOTE Increase in temperature increases pressure at constant volume according to the following formulae: pt = p0 (1 + 0,003 6 t) where pt is the nitrogen pressure, in megapascals, at temperature t; p0 is the nitrogen pressure, in megapascals, at reference te
39、mperature; t is the temperature variation. The rod shall be slightly oiled and protected against shocks. BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 10 7 Designation A gas spring in accordance with this part of ISO 119
40、01 shall be designated by: a) “Gas spring”; b) reference to this part of ISO 11901, i.e. ISO 11901-1; c) the type; d) the nominal stroke, in millimetres; e) the location of the pressure filling inlet for gas spring of type 900 to 2 500; EXAMPLE A gas spring of type 1 500, nominal stroke of 25 mm and
41、 with a pressure filling inlet located on the bottom (F) is designated as follows: Gas spring ISO 11901-1 - 1 500 25 - F BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 11 Bibliography 1 ISO 11901-21), Tools for pressing G
42、as springs Part 2: Specification of accessories 2 Council directive 97/23/CE “Pressure equipment” 1) To be published. BS ISO 119011:2003 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 08:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 11901-1:2003 BSI 389 Chiswick High Road London W4
43、 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revisio
44、n. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the
45、Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions o
46、f standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orde
47、rs for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Librar
48、y and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept
49、up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at