《ISO-2332-2009.pdf》由会员分享,可在线阅读,更多相关《ISO-2332-2009.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 2332:2009(E) ISO 2009 INTERNATIONAL STANDARD ISO 2332 Third edition 2009-01-15 Agricultural tractors and machinery Connection of implements via three-point linkage Clearance zone around implement Tracteurs et matriels agricoles Liaisons des instruments par lattelage trois point
2、s Zone de dgagement autour de linstrument Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 2332:2009(E) P
3、DF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, p
4、arties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relati
5、ve to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIG
6、HT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
7、 ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reserved Copyright International Organization for Standardiza
8、tion Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 2332:2009(E) ISO 2009 All rights reserved iii Foreword ISO (the International Organization for Standardizati
9、on) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be re
10、presented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards
11、are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internati
12、onal Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2332 was pr
13、epared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. This third edition cancels and replaces the second edition (ISO 2332:1993), which has been technically revised. Copyright International Organization for Standardization Provided
14、 by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/111111
15、1164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 2332:2009(E) ISO 2009 All rights reserved 1 Agricultural tractors and machinery Connection of implements via three-point linkage Clearance zone around impleme
16、nt 1 Scope This International Standard specifies the clearance zone around an implement for attachment to the three- point linkage of an agricultural wheeled tractor. It is applicable to the connection of agricultural implements to three-point linkages complying with ISO 730, and also where implemen
17、t couplers complying with ISO 11001-1, ISO 11001-2, ISO 11001-3 and ISO 11001-4 are used. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition
18、 of the referenced document (including any amendments) applies. ISO 730:2009, Agricultural wheeled tractors Rear-mounted three-point linkage Categories 1N, 1, 2N, 2, 3N, 3, 4N and 4 ISO 11001 (all parts), Agricultural wheeled tractors and implements Three-point hitch couplers 3 Terms and definitions
19、 For the purposes of this document, the following terms and definitions apply. 3.1 implement coupler device which facilitates the connection of tractor three-point linkage to the implement 3.2 transport pitch pitch reached by the mast when lifted to standard transport height from a position with low
20、er links horizontal and mast vertical ISO 730:2009, 3.2.24 4 Specifications The shape and dimensions of the clearance zone around implements for attachment to a three-point linkage shall be as shown in Figures 1 to 4 and as given in Table 1. Not included are adjustable levers and handles used to ope
21、rate the implement, or specifications referring to the width of the implements. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without lic
22、ense from IHS -,-,- ISO 2332:2009(E) 2 ISO 2009 All rights reserved Dimensions in millimetres Key 1 lower hitch point X hitch pin on both sides 2 upper hitch point Y clevis mounting on both sides a A or B (see Table 1). NOTE For dimension b5, see ISO 730. Figure 1 Clearance zone of implements where
23、transport pitch extends forward of vertical in raised position (view of details) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without li
24、cense from IHS -,-,- ISO 2332:2009(E) ISO 2009 All rights reserved 3 Figure 2 Clearance zone of implements where transport pitch extends forward of vertical in raised position (perspective view) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=
25、HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 2332:2009(E) 4 ISO 2009 All rights reserved Dimensions in millimetres Key 1 lower hitch point X hitch pin on both sides 2 upper hitch point Y clevis mounting on
26、both sides a A or B (see Table 1). NOTE For dimension b5, see ISO 730. Figure 3 Clearance zone of implements where transport pitch does not extend forward of vertical in raised position (view of details) Copyright International Organization for Standardization Provided by IHS under license with ISO
27、Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 2332:2009(E) ISO 2009 All rights reserved 5 Figure 4 Clearance zone of implements where transport pitch shall not extend forward of vertical in raised p
28、osition (perspective view) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 2332:2009(E) 6 ISO 2009 All r
29、ights reserved Table 1 Dimensions Dimensions in millimetres Tractor categorya 1N 1 2N 2 3N 3 4N 4 Symbol Description min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. Ab Upper hitch pin, vertical clearance 310 310 460 460 460 460 460 460 B Upper hitch pin, vertical clea
30、rance 160 160 280 280 280 280 280 280 C Hitch pins, horizontal position 35 35 35 35 40 40 40 40 D Lower hitch pin, horizontal clearance 95 95 95 95 105 105 135 135 E Lower hitch pin, vertical position 230 230 230 230 245 245 245 245 H Upper hitch pin, horizontal clearance 80 80 80 80 90 90 120 120 L
31、 Lower hitch pin, vertical position 150 150 150 150 200 200 200 200 S Upper hitch pin, width clearance 52 52 52 52 52 52 65 65 M c, d Mast height See ISO 730. N c Lower hitch point span See ISO 730. P Diameter of hitch pin shoulder See ISO 11001-3. a Tractor categories according to ISO 730. b Dimens
32、ion A applies where it is necessary to accommodate the upper hook to the coupler complying with ISO 11001-1. c It may be necessary to vary this dimension in the case of specialized implements. d If U-frame couplers according to ISO 11001-1, are used, dimension M should be in line with the upper hook
33、 vertical spacing as specified in ISO 11001-1. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright Int
34、ernational Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 2332:2009(E) ICS 65.060.01 Price based on 6 pages ISO 2009 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=HP Monitoring/1111111164 Not for Resale, 04/08/2009 03:58:48 MDTNo reproduction or networking permitted without license from IHS -,-,-