霍尼韦尔PKSR400完整装机步骤.pdf

《霍尼韦尔PKSR400完整装机步骤.pdf》由会员分享，可在线阅读，更多相关《霍尼韦尔PKSR400完整装机步骤.pdf（26页珍藏版）》请在三一文库上搜索。

1、实用文档 文案大全 PKS C400装机步骤 Generate Configuration Files Run Experion PKS System Initialization DVD in Windows. 在一台计算机上放入INITIALIZATION DVD，自动运行安装程序。 选择 Launch Setup 选择 Generate Configuration Files Click Next to continue. 实用文档 文案大全 选择所要安装的机器类型，上图是所支持的Station 的型号。 这是所支持的Server 的型号，下面以DELL T5500安装 F-Statio

2、n 为例 实用文档 文案大全 这里输入计算机名称、用户帐户和密码， 在初始化盘作安装配置文件时，需要将用户的名字设为系统默认的名称： Experionadmin ，密码随意。此用户名也可使用其它名称，但绝对不可以设为 administrator或 mngr 或 HPSinstall 等名称，这些用户在使用初始化盘安装后会被禁 掉，将无法登陆计算机。 如果所输入密码不符密码安全性时会有提示，可以选择忽略这个问题继续安 装，也可返回修改密码。 实用文档 文案大全 这里选择网络类型及网络定义，点击下一步 这里是一个汇总的信息，点击Generate Product Install Config. Fi

3、les，系统 提示需要 Installation DVD 实用文档 文案大全 然后又出现节点类型画面 选择好后点NEXT （安装服务器，请选择“Server(ESV) ” ；若安装操作站请 选择相应类型的操作站，如“Console Station(ES-C)”或“ Flex Station(ES- F)”） 实用文档 文案大全 按照以上选择后选NEXT （注意“ Customer Information”里面的两项中填写 项目名和用户公司名称） 实用文档 文案大全 这里填入的Password 应与前面的尽量保持一致，填好之后选NEXT, 下一步中点 Continue ，下一步在Save Con

4、fig.Files中选择一个保存配置文件的路径，保存好之后 拷贝到 U 盘中 将保存有安装配置文件“Config.Files ”的 U 盘插到将要安装PKS R400 的机器上，然 后启动计算机，插入Initialization光盘，启动时按着F12 ，进入到安装界面，系统会自 动安装，在安装过程中系统会提示选择安装配置文件，选择到U 盘中存的 “Config.Files ”即可。以下是详细安装步骤 ?In the target machine, insert Experion PKS System Initialization media and boot from the Experion

5、 PKS System Initialization media. ?Ensure that Boot Sequence in BIOS is set to boot from CD/DVD drive first. Please keep watching the screen while booting, and press any key as soon as you see the message “Press any Key to Boot from CD or DVD” ?When the system boots from Experion PKS System Initiali

6、zation media, WinPE is loaded into the target machine and the Experion PKS System Initialization PreInstall Utility screen appears. Browse to the configuration files and select InitMediaOptions.xml file. Click Next. This xml file can be located on a floppy disk, local system drive, or USB pen drive.

7、 ?Experion PKS System Initialization PreInstall Utility loads the configuration information from Options files. You can select “Use Drive C:” if they want to format only C drive and install OS on this drive. In this case, data on the other 实用文档 文案大全 partitions will be retained. This option needs to

8、be selected only if the system is having more than one partition and no raw partitions. ?Enter configuration details for hard disk in the Disk Configuration section. ?Select the appropriate media location. 这里选 DVD ?Enter the IP details, Subnet Mask, and Default Gateway in the Network Configuration f

9、or local machine section. Click Next. ?Select the I accept the terms in the License agreement radio button on the License Agreement screen after reading the EULA. Click Install. If it is a media-based install, the system prompts for the media. ?Once the OS installation is completed, insert Experion

10、PKS System Initialization DVD again when you see this Experion PKS System Initialization R400.1 dialog box. If the autorun dialog pops up, close the dialog. During installation, if you see “Restart Now ” prompts, no action is expected. The system will reboot automatically. During installation, if yo

11、u see any “Found New Hardware ” messages, no action needs to be taken. The system restarts several times automatically during Experion PKS System Initialization. If the media is already present in the local machine, installation proceeds without prompting Experion PKS System Initialization media. In

12、stall status will appear showing which feature is being installed/run, an approximate time for the feature and overall install to run and a description/message area that gives information for the install. The R400.1 Experion PKS System Initialization sequencer is running in the background sequential

13、ly running install features and communicating to the status. If product installation was selected installation DVD is prompted. Click Cancel if you want to cancel the install. It can be restarted at the point of cancellation at a later time by running setup.exe. Click OK to finish the installation o

14、nce you get the install complete message. The system reboots automatically. If it fails to automatically reboot, then reboot the computer manually. Click setup.exe to restart the installation Two methods to install PKS Configuration files to target computer. 实用文档 文案大全 二.安装后的系统配置 1. If a software pro

15、tection key (dongle，软件狗 ) is supplied in the Experion PKS media box, insert the key into one of USB interface in the computer. 2. After installation, Check the FTE Device Index & the FTE setting as follows: (1) From Start menu, right click Network or right click the Network icon in notification area

16、 of task bar and select Properties. (2) Click Network and Sharing Center.Check the Network Adapter scanning order. (3) Select Manage network connections from the left menu. (4) Right-click one of the FTE network connections (Yellow or Green) and then click Properties. (5) Select Continue to the User

17、 Account Control Prompt. (6) Select Honeywell FTE Mux-IM Protocol Driver, and then click Properties. (7) Verify FTE MUX-IM Protocol Driver Properties dialog: Select Configure tab. (8) Select the Honeywell FTE Adapter #1in the left pane. Set/Verify the values for the following: Device Index Value for

18、 the machine - Change the value to a unique number from 1-511. Verify the following values: The IPMC Destination Address (this is the multicast address assigned to the FTE Community default as 234.5.6.7) UDP Destination Port, Default is 51966 UDP Source Ports Port, Default is 47837 Note: You can mod

19、ify the IPMC address and the UDP source and destination ports, but it is recommended to retain the default settings. Click OK. 实用文档 文案大全 (9) From the Network Connections window: Select the Honeywell FTE Adapter #1, right-click the adapter and select Properties. (10) Select Continue to the User Accou

20、nt Control Prompt if it appears. (11) Verify the FTE Adapter #1 Properties: Select Internet Protocol Version 4 (TCP/IPV4), select Properties. (12) Verify IP Address and other IPV4 Settings. Correct any values that are incorrect or missing and then click OK. (13) Reboot your computer. (14) Log on bac

21、k as local administrator. (15) Wait until the machine has completed all the process starts and network connections. Verify Network Settings using IPConfig /all command from a command window: If FTE Mux Driver is working correctly, it will show up in the IPCONFIG as Honeywell FTE MUX-IM Virtual Minip

22、ort Driver. 3. New Account and User Group Computer manger configuration local user and groups right click “ user” Click “ new user ” to create a new account Double click the New Account Member of Add Advanced Find now Add the New Account to user group “ Administrator ” &” Product Administrator” 实用文档

23、 文案大全 4. HOST Configuration You must identify the computer name and associated IP address of each Experion PKS server and Console Station in the hosts file. Both server and client computers require a modified hosts file with identical entries, so you can edit the hosts file on one computer and then

24、copy it to each computer in the Experion PKS system. The hosts file is located in C:WINDOWSsystem32driversetc. 127.0.0.1 localhost 10.38.1.129 PKSServerA PKSServerA0 10.38.1.131 PKSServerB PKSServerB0 10.38.1.133 STN01 10.38.1.135 STN02 5. Experion PKS Patch Configuration The following section descr

25、ibes installed service patches, service packs and updates for the Honeywell Experion PKS Server. Includes upgrades, new system features and bug fixes The procedure assumes the individual performing the build task is both fully trained and familiar with Honeywell Experion PKS Server software. He also

26、 has access to the Experion website and priviledges/access that allow them to download all current patches etc. Installation for each patch/upgrade will be described by its accompanying SCN (Software Change Notice) below is a table for record purposes and should be filled in when each patch is appli

27、ed. PERC Firmware 6.3.0-0001,A12 MS Hotfix Controller Patch1 Server Patch 1 HMIWeb Patch 2 System Management Patch 2 ExperionPKS.R400.Server.Patch102.PAR1-J4C742 实用文档 文案大全 ExperionPKS_R400.1_HMIWeb_Patch_6_0_143_5200_PAR1-JD8OA7 6. 安装中文 Change System Locale to Chinese (Simplified, PRC). 将系统改为简体中文 un

28、lock logon for mngr. 解锁登陆 mngr 用户，可以参考下面截屏 入下命令 Run gpedit.msc secpol.msc ?log on as mngr account, open Regional and Language Options, change formats & location to Chinese & China. ?log on as user-defined administrator account, open Regional and Language Options, change formats & location to Chinese

29、 & China, then change the system locale to Chinese (Simplified, PRC). ?reboot. ?Copy to reserved accounts ( check “ Defalut user account” ). ?lock logon for mngr 实用文档 文案大全 ?Open Registry Editor, navigate to HKEY_LOCAL_MACHINESOFTWAREHoneywellExperion PKS Server ?Add a string value SQLCollation and m

30、odify its data as Chinese_PRC_CI_AS. 如下图 所示 实用文档 文案大全 ?Bring the server down to Database Only level. ?Run command prompt as administrator , type installsqlobject EMSEvents /c 如下图所 示 详细设置步骤请参考附件 Chinese Setting 7. 检查 Dongle 和 License 中文的安装很容易造成License的丢失，需要动作Change License。 否则 Server Redundancy 中的 hd

31、wbld redun.hdw 不能执行。 8. Configuring Experion server redundancy (1) Choose Start All Programs Honeywell Experion PKS Server Start-Stop Experion Server. The Experion PKS Server dialog box appears. Click the stop button. If prompted, click Yes to confirm the action. Wait for the server to change to sto

32、p state. It may take several minutes for the Experion server to stop. (2) 分别在两台服务器 (PKSServerA 和PKSServerB) 上, choose Start All Programs Honeywell Experion PKS Server Diagnostic Tools Experion Command Prompt to open the Experion Command Prompt window. 在“ Experion Command Prompt”命令行窗口中输入命令：hdwbld red

33、un.hdw 并回车 执行以上命令后，如果窗口提示errors 为0，那么表示命令执行成功，重启两台服务 器，当两台服务器重启后会自动互相识别，并分别变为“Primary ”和“ Backup ”。 实用文档 文案大全 两台冗余服务器互相识别出主、备后，需要对这两台服务器进行同步配置，如下： “Synchronizing the server databases” on page 115 “Synchronizing the Engineering Repository database” on page 117 “Synchronizing the Enterprise Model data

34、base” on page 118 For more information, go to Knowledge Builder: Experion R400 Configuration Server and Client Configuration Guide Configuring and monitoring a redundant server system. 9. limit SQL Server memory usage 10. Setting up time synchronization 时钟源的配置分为三种情形，即主时钟源（Authoritative Root Server），

35、备份时钟源 （secondary NTP server）以及时钟同步客户端(NTP clients ，例如所有的操作站均是 时钟同步的客户端)，还有控制器的时钟同步配置，详细步骤如下： Setting up time synchronization in a workgroup without an external time source checklist (a)Setting up the authoritative root server This topic describes setting up your primary Experion server as the author

36、itative root server in your time hierarchy. To set up an authoritative root sever 1 In Windows Explorer, go to C:program filesHoneywellExperion PKSUtilitiesNTPSetup. 2 Double-click the NTPConfig.exe file. The NTP Configuration dialog appears. 3 Click Setup Authoritative Root Server. 实用文档 文案大全 Severa

37、l screens appear while the configuration is applied. No input is required. 4 Click Exit. (b)Setting up the secondary NTP server This topic describes setting up your secondary Experion server as your secondary NTP server in your time hierarchy. Prerequisites ? You need to know the IP address or compu

38、ter name of the authoritative root server. If you use a computer name, it must resolve to an IP address using Host, DNS, or other resolution service. To set up your secondary NTP server 1 In Windows Explorer, go to C:program filesHoneywellExperion PKSUtilitiesNTPSetup. 2 Double-click the NTPConfig.e

39、xe file. The NTP Configuration dialog appears. 3 Click Setup Secondary Server. The NTP Server Information dialog box opens. 4 In the Up-Stream Time Source box, type the IP address or computer name of the authoritative root server. 5 Click OK. 6 Click Exit. (c)Setting up NTP clients in a workgroup wi

40、thout an external time source This topic describes how to set up NTP clients on such as Console Stations and Flex Stations. Prerequisites ? You need to know the IP address or computer name of the authoritative root server and the secondary server. If you use a computer name, it must resolve to an IP

41、 address using Host, DNS, or other resolution service. ? If you are setting up clients on Windows XP Professional, you must use the computer name of the authoritative root server and the secondary server. The computer name must resolve to an IP address. To set up NTP clients 1 In Windows Explorer, g

42、o to C:program filesHoneywellExperion PKSUtilitiesNTPSetup. 2 Double-click the NTPConfig.exe file. The NTP Configuration dialog appears. 3 Click Change/Configure Client. The NTP Server Information dialog box opens. 4 In the First NTP Server box, type the IP address or computer name of the authoritat

43、ive root server. If this client is using Windows 7, type the computer name of the authoritative root server. 5 In the Second NTP server box, type the IP address or computer name of the secondary server. If this client is using Windows 7, type the computer name of the secondary server. 6 Click OK. 7

44、Click Exit. (d) Setting up control hardware to receive time from an NTP server in a workgroup without an external time source This topic describes setting up C300 controllers to receive time from your NTP servers (Experion servers). Prerequisites ? You need to know the IP address or computer name of

45、 the authoritative root server and the secondary server. If you use a computer name, it must resolve to an IP 实用文档 文案大全 address using Host, DNS, or other resolution service. To set up control hardware 1 In Control Builder, choose Tools System Preferences. The System Preferences dialog box opens. 2 C

46、lick the Embedded FTE tab. 3 In the Primary Server box, type the IP address or computer name of the authoritative root server. 4 In the Secondary Server box, type the IP address or computer name of the secondary server. 5 Select the Edit network parameters check box. 6 Click OK. 11. Installing the W

47、eb Server (IIS) role on the Experion Server. 更详细的信息，可以参考Knowledge Builder：Experion R400 Installation and UpgradesSupplementary Installation Tasks GuideInstalling the Web Server (IIS) role 12. Check the Knowledge Builder Index Functon If KB s search function doesnt work, navigate Indexing O ptions-Mo

48、dify-Show all locations 控制面板 -索引项 实用文档 文案大全 Navigate to Knowledge Builder Server locations C:ProgramDataHoneywellPST_Server and C:ProgramDataHoneywellPSTKB_Favorites (default locations) and check the checkboxes to add these locations to be indexed. 详细设置步骤请参考附件 实用文档 文案大全 13. Defragmenting the hard dr

49、ive.进行磁盘碎片整理 以下只适用于操作站的设置，服务器不需要。 14. Install MS Excel. 首先安装微软Excel ，对于 PKS R400 ，只能安装MS Excel 2007 sp2 或 MS Excel 2010 英文版 Setting up Microsoft Excel Data Exchange unlock logon for mngr. 解锁登陆 mngr 用户，可以参考下面截屏 merge excel reports.reg. Start-Run: runas /user:mngr “C:Program FilesHoneywellExperion PKSclient xldataexactivatemede.vbs“ Start-Run: runas /user:mngr “excel.exe“ Set Excels Trust Center into Me dium level. lock logon for mngr. 15. 取消屏保 屏幕右击 Personalize 16. 关于 USB 口的禁用 HKEY Local MACHINE SYSTEM C