《【AS澳大利亚标准】AS 2505-4-2002 Metallic materials Method 4 Wire—Reverse bend test.doc》由会员分享，可在线阅读，更多相关《【AS澳大利亚标准】AS 2505-4-2002 Metallic materials Method 4 Wire—Reverse bend test.doc（9页珍藏版）》请在三一文库上搜索。
1、iAustralian StandardTMAS 2505.42002ISO 7801:1984Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 2007AS 2505.4Metallic materialsMethod 4:WireReverse bend testPREFACEThis Standard was prepared by Standards Australia Committee MT-006, Mechanical Testing ofMetals to supersede in part AS 2505.41981,
2、Methods for bend and related testing of metals, Method4: Wire.ThisStandardis identicalwith andhasbeen reproducedfromISO 7801:1984,Metallic materialsWireReverse bend test.This Standard is Method 4 of a series of Standards on the methods of bending wire and related testing of metals. The series compri
3、ses the following Methods:AS2505Metallic materials2505.1Method 1:Sheet, strip and plate2505.2Method 2:Bars, rods and solid shapes2505.3Method 3:Tubular products2505.4Method 4:WireReverse bend test2505.5Method 5:WireSimple torsion test2505.6Method 6:WireWrapping testAs this Standard is reproduced fro
4、m an International Standard, the following applies:(a)Its number does not appear on each page of text and its identity is shown only on the cover and title page.(b)In the source text, this International Standard should read this Australian Standard. (c)A full point substitutes for a comma when refer
5、ring to a decimal marker.NOTESiiAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 20074Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 2007 Standards A.auAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 2007Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 2007Accessed by UNIVERSITY OF SO
6、UTH AUSTRALIA on 02 Mar 2007NOTES5Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 20076Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 2007This Australian Standard was prepared by Committee MT-006, Mechanical Testing of Metals. It was approved on behalf of the Council ofStandards Australia o
7、n 17 May 2002 and published on 20 May 2002.The following interests are represented on Committee MT-006: Australasian Railway AssociationAustralian Aluminium CouncilAustralian Industry GroupBureau of Steel Manufacturers of AustraliaCSIROInstitute of Materials Engineering AustralasiaNATAKeeping Standa
8、rds up-to-dateStandards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important th
9、at readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased.Detailed information about Standards can be found visiting the Standards Australia web site at .au and looking up the relevant Standard i
10、n the on-line catalogue.Alternatively, the printed Catalogue provides information current at 1 January each year, and the monthly magazine, The AustralianStandard, has a full listing of revisions and amendments published each month.We also welcome suggestions for the improvement in our Standards, an
11、d especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at .au, or write to the Chief Executive, Standards Australia International Ltd, GPO Box 5420, Sydney, NSW 2001.Originated as AS 2505.41981. Second edition 2002.This Standard was
12、issued in draft form for comment as DR 02089.COPYRIGHT Standards Australia InternationalAll rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.Published by Standards Australia International LtdGPO Box 5420, Sydney, NSW 2001, AustraliaISBN 0 7337 4534 2Printed in AustraliaAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 02 Mar 2007This page has been left blank intentionally.