《磁力研磨机说明书.doc》由会员分享，可在线阅读，更多相关《磁力研磨机说明书.doc（10页珍藏版）》请在三一文库上搜索。
1、顺佳研磨科技有限公司 磁力精密研磨机PRECISION MAGNETIC GRINDERhttp:/www.dgs un 机械原理简介Mecha nic Prin ciple利用神奇磁场力量传导不锈钢针磨材产生加速旋转动作，高效率 达到精密研磨去除毛边和抛光洗净效果With the use of the magical force of magnetic field, making the stainless steel pins rotate very fast, to de-burr, polish and clea n the workpieces high-effectively an
2、d precisely.1、特点 Features1）卓越快速去除毛边能力，细小内孔、内管、夹缝死角均可高效研磨， 绝不变形及伤表面，不影响精度。Have excellent ability of fast de-burring, high efficiently grinding small inner holes, inner pipes, crevices, etc. Make NO damage to the surface of workpieces, and DO NOT affect the accuracy of workpieces.2）加工速度快，一次315分钟即可完成，可
3、在机器运转中替换工件。Fast grinding or polishing, only 315 minutes is needed for each time. Workpieces can be cha nged duri ng the mach ine running.3）操作方面简单，成本低，无污染，不锈钢针为永久性磨材。Simple and convenient operati on, low cost, no polluti on. The sta ini ess steel pins are perma nent abrasives.2、用途 Application金饰业打磨洗净工
4、作，成品表面抛光处理，去除氧化薄膜工作，锈 蚀去除处理，电镀或喷漆前处理，烧结痕迹处理，零件残磁去除。Use in metal in dustry for Gringding, clea ning, polishi ng surface of workpiece, removing layer of oxide on the workpiece, derust ing, process ing before plati ng or painting, process ing the marks of sin teri ng, and demag netiz ing the workpiece.
5、3、说明 Description1）研磨速度快，平均一次研磨时间约315分钟，替换工件快，可在机器运转过程中替换零件。Grin di ng quickly, it on ly takes 315 minu tes for each time on average. Easy and fast cha nging the workpieces, the workpieces can be cha nged duri ng the machi ne running.2）操作简单，绝对安全，完全免技术，一人可操作多台机器。Simple operatio n, absolute safety. One
6、 pers on can operate multiple machi nes.3）成本低，不锈钢针为永久性磨材，消耗极低，唯一的耗材为研磨液。 无污染，研磨液含95%水分，故无毒性及发生火灾之虑。Low cost, the stai nless steel pi ns are perma nent abrasives. The only con sumable item is Grinding （Brighte ning） Fluid. No polluti on. The grinding （brighte ning） fluid contains 95% moisture, and is
7、 non-toxic; you can have no worry about fire on it.4）研磨完成后，工件好处理，可用筛网、筛桶或磁铁，轻易将工件和 不锈钢针分开。The workpieces can be easily dealt with after grinding. Can use a sieve mesh, sieve drum or magnet to easily separate the workpieces from the pins4、 安装环境Installing Environment1）无水滴、蒸汽、灰尘及油性灰尘之场所。Place WITHOUT w
8、ater drops, vapor, dust or oily dust.2）无腐蚀、易燃性之气体、液体。Place WITHOUT corrosive, flammable liquid or gas.3）无漂浮性的尘埃及金属微粒。Place WITHOUT float ing dirt and metal particle.4）紧固无振动之场所。Place of no vibratio n.5、操作顺序1）将机器连接在有可靠接地的标准电源中。各型号对电源要求如下:型号电源要求SJ-6603 相 380V，50/60Hz，13ASJ-6503 相 380V，50/60Hz，13ASJ-645
9、单相 220V，50/60Hz, 13ASJ-635单相 220V，50/60HZ，13ASJ-628单相 220V，50/60HZ，13AConnect the machi ne to the sta ndard power supply with reliable gro und lead. The power supply for each model is as below.MODELPOWER SUPPL YSJ-6603 Phase 380V 50/60Hz，13ASJ-6503 Phase 380V 50/60Hz，13ASJ-645Single Phase 220V，50/60
10、Hz，13ASJ-635Single Phase 220V，50/60Hz，13ASJ-628Single Phase 220V，50/60Hz，13A2) 将放有适量工件及研磨材料之塑料质容器放在研磨槽中间位置，开 启电源(ON)，设定总研磨时间TOTAL TIMER(H小时.M分。S秒)及正 反转时间REV/FWD TIMER、设置工作速度 SPEED SET(0-10V模拟速 度)，9V等于1400转左右。Put the plastic grinding container (e.g.a tub) with proper amount of workpieces and abrasive
11、s in the middle of the grinding trough, tur n on the power and set the total time (Hour. Min utes. Seco nd), the REV/FWD time, and the worki ng speed (010V9V=1400 r/mi n).3) 启动运行按钮START，机器开始工作。Press the “START Key, and the machine starts working.4) 工作在设定时间完成后，应再次启动机器，拿走研磨桶进行清洗，然后按STOP按钮停止工作。(原因是工件在机
12、器磁场运转中才能消除 剩磁)After work finishing, should start again the machine and take away the grinding tub from the trough to clea n the workpieces, and the n stop the machi ne. (As the workpieces can only be demag netized dur ing the machi ne runnin g.)5) 用分选筛将不锈钢针分选后，放回桶内以便下次使用。Separate the sta in less ste
13、el pins with a sieve. The pin s can be used aga in.6、使用方法 Method of Usage1）使用塑料质容器，以免损坏工件。Use a plastic container, （e.g. a plastic tub.） to avoid damaging the workpieces.2）放入适量的不锈钢针，研磨液，水和工件进行研磨或者抛光。以下数据供参考：型号每次研磨时需用的不锈钢针、研磨液、水和工件的分量速度设定（仅供参考）SJ-660钢针0.4以下的约1000克，若0.5以上的钢针要用约2000克；研磨液60毫升；水6公斤；工件：非导
14、磁材料610千克，导磁材料1 4千克。9V(约 1400r/mi n)SJ-650钢针15002000克；研磨液4060毫升；水56公斤； 工件：非导磁材料58千克，导磁材料1-2.5千克。9V(约 1400r/mi n)SJ-645钢针约1200克，研磨液2040毫升；水35公斤；工件 非导磁材料36千克，导磁材料1-2千克。9V(约 1400r/mi n)SJ-635钢针约700克；研磨液2040毫升；水24公斤；工件： 非导磁材料13千克，导磁材料1千克。9V(约 1400r/mi n)*研磨工件时导磁材料分量为非导磁材料分量的1/3。工件超分量研磨，机器如有损坏本公司概不负责。Put
15、appropriate amount of stainless steel pins, grinding fluid, water and workpieces into the tub to grind or polish. The following amount is for refere nee.MODLEThe amount of pins, grinding fluid, water and workpieces to be used each timeSpeed Sett ing(On ly for refere nee)SJ-660Pins < 0.4, use abou
16、t 1000 grams, if the pins > 0.5, use about 2000 grams; grinding fluid 60ml, water 6 kg, workpiecesnon-magnetic material 610 kg.,magnetic materials 1-4kg9V(about 1400r/mi n)SJ-650Pi ns 15002000 grams; grin di ng fluid 4060ml, water 56 kg, workpieces non-mag netic material 58 kg.,magnetic materials
17、 1-2.5kg9V(about 1400r/mi n)SJ-645Pins 1200 grams; grinding fluid 2040ml, water 35 kg, workpieces non-mag netic material 36 kg.,magnetic materials 1-2kg9V(about 1400r/mi n)SJ-635Pins 700 grams; grin di ng fluid 2040ml, water 24 kg, workpieces non-mag netic material 13 kg.,magnetic materials 1kg9V(ab
18、out 1400r/mi n)7、研磨用不锈钢针选择Choice of grinding stainless pins1) 针愈粗研磨能力愈强，故选择针时以工件材质软硬为依据。不锈 钢或铁类可选择直径0.5mm以上针，铜铝等其材质较软材料可选择直 径0.5mm以下较适宜。当然磁力研磨机的磁力大小可无段调整，因此 经测试多次后，即可选定适当的磨材。The bigger the pins are, the better the grinding ability is. Thus, choose the pins should depe nd on the soft ness or hard nes
19、s of the workpiece material. Can choose pi ns with diameter over 0.5mm for Stai nless steel or Iron workpieces, and pi ns blow 0.5mm for softer material workpieces such as copper or alu minium.Of cause the magn etic force of the mach ine is adjustable, thus can test for more times to get a suitable
20、grinding pins.2）要研磨工件的孔径大小，决定针的精细及长短，另如要研磨工件 的孔内夹缝时，建议使用3mm长的针，效果较好。The holes of the workpieces decide the big or small, I ong or short pins to be used. If the cracks into the holes are to be grin ded, the 3mm long pin is suggested to be used for better effect.3）不锈钢针磨材为永久性材料，可连续使用。The stai nless ste
21、el pins are perma nent grinding materials, can be used for many times.&研磨液功用 Function of Grinding Fluid1）防锈、抛光、冷却、清洗、除油等功能。Rust-preve nt, polish ing, cooli ng, clea ning and oil removing etc.2）研磨液连续研磨约30分钟、温度可达70C，请注意轮流交换。The grinding fluid grinds for 30 minutes, its temperature can be 7 OC, ple
22、ase cha nge with cool one.3）如工件表面含油太多，需先清洗除油再研磨。If the surface of workpieces too oily, the oil should be removed first before grinding.9、注意事项 NOTES1）电源必须有可靠接地The power supply must have a reliable ground lead.2）变频调试器功能键不可随意修改（以出厂时设置为准）The function key of the frequency conversion adjuster should not b
23、e cha nged at will. （Factory sett ing is sta ndard.）3）研磨完成后，研磨工件必须在机器运转中拿走清洗（以免工件被磁化）After grinding finishes, workpieces should be taken away during the machi ne running, so that the workpieces are not magn etized.4）必须使用塑料质研磨桶，以免损坏工件To avoid damagi ng the workpieces, should use a PLASTIC container f
24、or grinding.5）研磨槽内不可进水，以免损坏机器。To avoid damaging the machine, the grinding trough should not be watered.10、机器保养 Maintenance of Machines1）每班清理研磨槽内掉下的钢针和水。Clean the grinding trough per shift.2）研磨槽内的胶垫每班使用前要清理钢针再使用。Clean the rubber mat on the grinding trough before grinding.3）研磨槽内排水管要保持畅通。Keep un blocke
25、d to the drain pipe of the grinding trough.4）机器表面要保持清洁、干爽。Keep the surface of the mach ine clea n and dry.5）机器后面及底下风扇过滤网每 30天要清理一次。Clean the strainers to the fans on the back and bottom of the machine every 30 days.0769- 8507 86961687631406:QQ电机 0.75/1.5KW付号名称付号名称UF变频器SF钮子开关QF漏电开关SB按钮开关KM接触器KT时间继电器KA中间继电器LD运行指示灯电机3.7KW付号名称付号名称UF变频器SF钮子开关QF漏电开关SB按钮开关KM接触器KT时间继电器KA中间继电器LD运行指示灯