《微动开关规格书.docx》由会员分享，可在线阅读，更多相关《微动开关规格书.docx（5页珍藏版）》请在三一文库上搜索。
1、文件类型TYPE OF FILE规格书SPECIFICATION文件编号FILE NO.产品系列SERIES微动开关MICRO SWITCH产品型号TYPEDMS02系列页次PAGE1 of 4发布日期ISSUED DATE2009.03.24修正日期AMENDED DATE版本VERSIONA1温度范围Temperature range使用温度范围：Temperature range for use测试环境条件：Test circumstance condition :环境温度：-25 C 85 CAmbient temperature : -25 C 85 C相对湿度：45%85%Rela
2、tive humidity : 45%85%空气压力：102千帕Air pressure : 102KPa外观、结构和尺寸Appearance 、structure and dimension外观：Appearance:外观美观、没有生锈、伤痕、电镀不良、破裂，剥离现象。动作正常，换位 活晰。Nice appearance , free from rust , scar, bad platting , denude , normal action , clear conversion。3.2结构和尺寸：Structure and Dimension:参照有关外形图Reference to th
3、e relative250VAC125VAC250VAC250VAC125VAC250VAC1、1.12、3、3.14、额定值： CQC TUV : 5A UL: 10A 5ARating : CQC TUV : 5A UL : 10A 5A-25 C 125 C-25 C 125 C文件类型TYPE OF FILE规格书SPECIFICATION文件编号FILE NO.产品系列SERIES微动开关MICRO SWITCH产品型号TYPEDMS02系列页次PAGE2 of 4发布日期ISSUED DATE2009.03.24修正日期AMENDED DATE版本VERSIONA1项目Item测试
4、条件Test Condition规格Performance5、机械，隹能 Mechanical Performance5.1动作力Operating Force开关垂直丁操作方向放置，在按钮一侧逐渐 施力，测量开关导通所需的最大力度。Vertical placing the switch with the direction of switch operation, then gradually increasing the force, measure demanded maximum force that switch continuity.0.6 =0.2N5.2端子强度Terminal
5、 strength在端子的顶部施加一向内推的25N静负荷， 持续60秒。Enforce push-inward static 25N load on the top of terminal, lasting 60 seconds端子无损伤，脱落，开关 功能动作正常。No damage, leafing, switch function action is normal.5.3可焊性试验Solder-Ability将端子浸入熔融的锡槽内，温度为235±5C, 时间为3±0.5秒。Immerse the terminal to the molten solder tank, t
6、emperature reach to 235 ±5 C ,time reach to 3 0.5 seconds浸入的部分90%以上表 面被锡覆盖。90% of the surface will be covered by solder.5.4耐焊性试验Soldering resistance test端子的焊接部分浸入温度为260±5 C熔融的 锡炉内3±0.5秒。The welding part of terminal immerse molten solder at a temperature of 2605 Cfor 3 0.5 seconds.上，、一
7、，斗一，本体无变形，能两足丁机 械、电气性能Without deformation of base,can satisfymechanical, electronic performance.手工烙铁焊接：焊接温度350±5C,焊接时 间3±0.5秒。焊接时在端子上不能施加异常 压力。Manual iron welding: welding temperature: 350 ±5 C ,welding time: 3 也.5 seconds. When welding, can' t enforce anomaly pressure on the term
8、inal.文件类型TYPE OF FILE规格书SPECIFICATION文件编号FILE NO.产品系列SERIES微动开关MICRO SWITCH产品型号TYPEDMS02系列页次PAGE3 of 4发布日期ISSUED DATE2009.03.24修正日期AMENDED DATE版本VERSIONA1项目Item测试条件Test Condition规格Performance5.5动作位置见成图OP=11.8+1.5/-0mm6、电气性能 Electronic Performance6.1接触电阻Contact resistance在1KHz小电流下测量。Being measured at
9、 1KHz small current.50毫欧姆以下50演 MAX.6.2绝缘电阻Insulation resistance在端子之间和端子与外壳之间施加 DC500V , 一分钟后测量。Measurement shall be made enforcing DC500V between terminals and between terminals and frame for 1 minute.100兆欧姆以上100MQ MIN.6.3耐电压Withstand voltage在极与极之间施加 AC1000V , 0.5mA 1分 钟，在极与操动轴之间施加AC1500V ,0.5mA 1 分
10、钟。Enforce AC1000V, 0.5mA between pole and pole in 1 minute ,enforce AC1500V,0.5mA between pole and frame in 1 minute.无击穿现象出现。No breakdown.7、耐久性能 Durability7.1机械寿命Mechanical life每分钟30次的速度连续工作5E4次Operating 5E4 cycles at a rate of 30cycles per minute外观，动作功能正常7.2电气寿命Electrical life额定负载条件下，每分钟30次的速度操作>
11、; 1E4 次.Operating > 1E4 cycles at a rate of 30cycles per minute under rate loading on conaition1.温升W5KTemperature raising 55K文件类型TYPE OF FILE规格书SPECIFICATION文件编号FILE NO.产品系列SERIES微动开关MICRO SWITCH产品型号TYPEDMS02系列页次PAGE4 of 4发布日期ISSUED DATE2009.03.24修正日期AMENDED DATE版本VERSIO NA1项目Item测试条件Test Conditi
12、on规格Performance8、而寸候性 Weather Ability8.1耐局温试验Heat test在125±2 C环境中放置72小时，再放在正常 环境中60分钟后进行测试。Putting at 125 坦 C for 72 hours. Test after keeping in normal condition for60 minutes.1、接触电阻50毫欧以下Contact resistance 50m Q MAX.2、绝缘电阻100兆欧以 上Insulation resistance 100MQ MIN.3、耐电压 1000V, 0.5mA 1分钟无击穿 Withs
13、tand voltage1000V,0.5mA,no breakdown.4、无任何迹象显示机械及电气性能之损坏 No sign of damage mechanicalandelectronic performance.8.2耐湿试验Anti-humid test在温度为40 土 2 C ,相对湿度为91%-95%RH 的环境中放置96小时，再放在正常环境中60 分钟后进行测试。Putting at 40 土 2 C , 91%95%RH for 96 hours. Test after keeping in normal condition for 60 minutes.8.3耐低温试验A
14、nti-low temperature test在-25均C的环境中放置16小时，再放在正 常环境中60分钟后进行测试。Putting at -25 =3 C for 16 hours. Test after keeping in normal condition for 60 minutes.8.4温度交变试验Temperaturecycling test在如图示之环境中，循环5次后，再置丁正常 环境中，30分钟后进行测试。In FIG. For 5 cycles, test after kept in normal condition for 30 minutes.+125 C-25 C:21 One cycle21Hours