《Gold Series 17 Closed Cell Spray Foam Insulation：黄金系列17闭孔喷涂泡沫保温材料.docx》由会员分享，可在线阅读，更多相关《Gold Series 17 Closed Cell Spray Foam Insulation：黄金系列17闭孔喷涂泡沫保温材料.docx（3页珍藏版）》请在三一文库上搜索。
1、.(The Gold Series) Plural, 1.7 pound Insulating Spray Foam*;3 DESCRIPTION SPEC Technologies 1.7 GOLD is an HFC 245 fa blown, liquid spray system which cures to a low density rigid polyurethane insulation developed for application to sidewalls, cavity fill and tanks at substrate temperatures as low a
2、s minus 40°F (4°C). It is available in three reactivity variations to meet a broad range of surface temperature conditions. SPEC Technologies 1.7 GOLD has undergone preliminary testing and should meet a Class I Fire Rating standard. Polyurethane foam used on the interior of a structure int
3、ended for human occupation must be protected by an approved 15 minute thermal barrier. When used on the exterior of structures and on structures that are not intended for human occupation these restrictions do not apply. Please check local codes for further information. When exposed to open flame, c
4、ured polyurethane foam may present a serious fire hazard.Product DescriptionSPEC Technologies 1.7 GOLD is a fast set polyurethane spray insulation system. SPEC Technologies 1.7 GOLD is a premium construction product, and is environmentally friendly. It exhibits superior insulation properties compare
5、d to other conventional insulation materials. SPEC Technologies 1.7 GOLD meets the highest flame retardancy standards for construction materials. SPEC Technologies 1.7 GOLD is easy to apply and its fast reaction time allows the contractor to complete difficult jobs quickly. UsesSPEC Technologies 1.7
6、 GOLD is a superior insulation material designed specifically for residential and commercial construction projects. SPEC Technologies 1.7 GOLD is flexible, accommodating movement of the substrate. SPEC Technologies 1.7 GOLD is designed interior applications only. SPEC Technologies 1.7 GOLD is recomm
7、ended for new construction and retrofit of existing structures. AdvantagesFast set, allows quick job turn-around, contains no Ozone Depleting substances. Seamless, expands to fill voids and prevents air movement. Flexible, allows for some building movement. Excellent Thermal Stability, and dimension
8、al stability, will not shrink under adverse weather conditions. Odorless, No Toxic Vapors after application, Class I Fire Retardancy rating.LimitationsSPEC Technologies 1.7 GOLD should not be used for exterior applications as the sunlight will rapidly degrade foam. It should not be used where foam w
9、ill stay submerged in water. Applicable codes must be strictly adhered to. .Typical Liquid PropertiesPROPERTY TEST METHOD TYPICAL VALUEViscosity “A”ASTM D-2196200-250 cps 77ºFViscosity “B”ASTM D-2196350-400 cps 77ºFWeight Per Gallon “A”ASTM D-147510.20 LBS/GallonWeight Per Gallon “B”ASTM D
10、-1475 9.80 LBS/GallonTypical ReactivityCream time3-4 seconds 25ºCRise Time12-16 seconds 25ºCTypical Physical PropertiesPROPERTY TEST METHOD TYPICAL VALUEDensityASTM D-16221.70±0.10 Lbs/ft3k-FactorASTM C-177.219 BTU in/ºFR-ValueASTM C-5186.75 ºF/BTU inFlame Spread IndexASTM E
11、-84-1”<20Smoke Generation IndexASTM E-84-1<200Water Vapor TransmissionASTM E96-952.55 Perm InchDimensional StabilityASTM D-2126-9400.3 % 28 Day, 158ºF, 97% RHService Temp Range-40 to 200 degrees FWater Absorbtion Rate0.055 lbs/ sq ft, 2” headTensile StrengthASTM D-1623-7825 PSIParallel to
12、 riseC-273-9421 PSIClosed Cell ContentD-2856C-490% by volumeWinter regular and summer grades availablePackagingOne Thousand Pound Kit: 500 Pounds of 'A' side and 500 Pounds of 'B' side.One Hundred Pound Kit: 50 Pounds of 'A' side and 50 Pounds of 'B' side.MixingPrior
13、to designing and installing a spray polyurethane foam interior insulation system, code officials should be consulted for recommendations and approvals. Federal, local and state building codes vary. All require that spray applied polyurethane foam insulation be covered with an approved 15 minute fire
14、 rated thermal barrier. One typically approved material is ½" (1 cm) gypsum wallboard applied over the spray polyurethane foam insulation. However, always check with local officials for recommendations and approvals. It is recommended that the approved thermal barrier be installed the same
15、 day the foam is applied. All hot work, i.e., welding, torches and open flame work, must have been completed prior to commencing the installation of the polyurethane foam insulation. Smoking in the same area while the spray polyurethane foam insulation is being applied shall be strictly prohibited.S
16、PEC Technologies 1.7 GOLD cannot be applied when substrate temperatures are below 40°F (4°C). Ambient conditions, component temperatures, spray gun mix efficiency and foam thickness also influence reactivity. Technical Service Personnel should be consulted whenever conditions are marginal.
17、 The aforementioned information on this product is to be used as a guide and is subject to change without notice. They are offered in good faith, but without guarantee, as conditions and methods and use of our products are beyond our control. Any obligation of the seller or manufacturer shall have n
18、o force or effect unless it is in writing and signed by officers of the manufacturer.SPEC Technologies 1.7 GOLD must be spray applied using approved equipment. Use 1:1 ratio pump, with appropriate material heaters, as required for individual application. Minimum Parameters for Processing SPEC Techno
19、logies 1.7 GOLDWorking Pressure1000-1500 psiWorking Temperature 120-140 ºFTYPICAL PHYSICAL PROPERTIES Properties shown are for materials sprayed onto a surface at room temperature and removed for physical testing. The values presented were derived from polyurethane foam, which was adequately mi
20、xed and properly metered at the specific ratio. If the polyurethane foam is not adequately mixed and properly metered at the specified ratio, the resulting values will not conform to the listed specifications.Prior to designing and installing a spray polyurethane foam interior insulation system, cod
21、e officials should be consulted for recommendations and approvals. Federal, local and state building codes vary. All require that spray applied polyurethane foam insulation be covered with an approved 15 minute fire rated thermal barrier. One typically approved material is ½" (1 cm) gypsum
22、 wallboard applied over the spray polyurethane foam insulation. However, always check with local officials for recommendations and approvals. It is recommended that the approved thermal barrier be installed the same day the foam is applied. All hot work, i.e., welding, torches and open flame work, m
23、ust have been completed prior to commencing the installation of the polyurethane foam insulation. Smoking in the same area while the spray polyurethane foam insulation is being applied shall be strictly prohibited.SPEC Technologies 1.7 GOLD cannot be applied when substrate temperatures are below 40&
24、#176;F (4°C). Ambient conditions, component temperatures, spray gun mix efficiency and foam thickness also influence reactivity. Technical Service Personnel should be consulted whenever conditions are marginal. The aforementioned information on this product is to be used as a guide and is subje
25、ct to change without notice. They are offered in good faith, but without guarantee, as conditions and methods and use of our products are beyond our control. Any obligation of the seller or manufacturer shall have no force or effect unless it is in writing and signed by officers of the manufacturer.
26、The information herein is believed to be reliable but unknown risks may be present. ALL WARRANTIES OF ANY KIND, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND THAT GOODS ARE OF MERCHANTABLE QUALITY, ARE SPECIFICALLY DISCLAIMED. Contact SPEC Technologies for inform
27、ation concerning its limited warranty and its availability. Disclaimer: The data presented herein is not intended for use by nonprofessional applicators, or those who do not purchase or utilize this product in the normal course of their business. The potential user must perform any pertinent tests i
28、n order to determine the products performance and suitability in the intended application, since final determination of fitness of the product for any particular use is the responsibility of the buyer.This information and technical advice provided herein are believed to be reliable and accurate to t
29、he best knowledge of SPEC Technologies Inc. as based on tests and should serve only as recommendation. As the seller, SPEC Technologies Inc. makes no representation or warranties of any kind, expressed, implied or statutory, including but not limited to all implied warranties of merchantability or f
30、itness for use or a particular purpose for the product. SPEC Technologies Ilc. makes no representations or warranties as to the result of the use of the product and assumes no obligation or liability in the connection therewith. SPEC Technologies Ilc. is not liable for any incidental or consequentia
31、l damages of any sort from the use of this product. The information provided herein is subject to change ant any time without notice. Information changes may include, but are not limited to, commercial and technical changes, changes in pricing, Physical characteristics and packaging.All guarantees a
32、nd warranties as to the products supplied by SPEC Technologies Ilc. shall have only those guarantees and warranties expressed by the manufacturer. The buyers sole remedy as to the material claims will be against the manufacturer of the product. The aforementioned data on this product is to be used a
33、s a guide and is subject to change without notice. The information herein is believed to be reliable, but unknown risks may be present. NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING PATENT WARRANTIES OR WARRANTIES OF MERCHANTABILITY OR FITNESS FOR USE, ARE MADE BY manufacturer. WITH RESPECT TO PROD
34、UCTS OR INFORMATION SET FORTH HEREIN. Nothing contained herein shall constitute a permit or recommendation to practice any invention covered by a patent without a license form the owner of the patent. Accordingly, buyer assumes all risks whatsoever as to the use of these materials, and buyers exclus
35、ive remedy as to any breach of warranty, negligence, or other claim shall be limited to the purchase price of the materials. Failure to adhere to any recommended procedures shall relieve SPEC Technologies Ilc. and the manufacturer of all liability with respect to the materials and their use thereof.