《STD3100橡胶剪切模量及判定.docx》由会员分享,可在线阅读,更多相关《STD3100橡胶剪切模量及判定.docx(4页珍藏版)》请在三一文库上搜索。
1、.STANDARDSTD 3100Utgåva/IssueSida/Page24Bestämning av skjuvmodul. Gummi.Determination of shear modulus. Rubber. 橡胶剪切模量的判定ProvningsmetodTesting methodOrienteringIntroductionDenna standard avser bestämning av skjuvmodul (kvadrupelmetoden) och överensstämmer i ska med ISO 1827-
2、1976.This standard refers to determination of the shear modulus (guadruple shear method) and essentially agrees with ISO 1827-1976.1Provkropp1Test specimenStandardprovkroppen består av fyra identiska gummielement: tjocklek 4 ± 0,1 mm, bredd 20 ± 0,1 mm och längd 25 ± 0,1 mm.
3、 De fastvulkas mellan styva stålplattor, tjocklek 5 + 0, -0,1 mm enligt figur 1. Tre provkroppar används för varje prov.The standard test psecimen consists of four identical rubber elements: thickness 4 ± 0,1 mm, width 20 ± 0,1 mm and length 25 ± 0,1 mm. They are bonded
4、 to stiff sheet metal plates, thickness 5 + 0, -0,1 mm as per fig 1. Three test pieces are used for each test.1.1Tillverkning1.1ManufacturingStålplattorna behandlas på normalt sätt med bindemedel. Ovulkat gummimaterial utstansas tillräckligt stort så att skägg erhå
5、lls vid vulkningen.The sheet metal plates are treated in the usual way with a bonding agent. Unvulcanized rubber material is punched big enough for flash to be achieved when vulcanized.Denna utförs antingen genom formpressning av den sammansatta provkroppen, eller genom sprutpressning.This is e
6、ither made through compression moulding of the composite test specimen or through transfer moulding.Vulkningen sker vid lämplig temperatur under bestämd tid.The vulcanization is carried out at an adequate temperature for a fixed time.Vid uttag av provkropp ur formen får provkroppen ej
7、 utsättas för onödig dragpåkänning.When taking the test specimen out of the form it must not be exposed to any unnecessary tensile stress.2Konditionering2ConditioningProvkropparna ska efter framställning förvaras minst 16 timmar och max 4 månader i normal labo
8、ratorieatmosfär innan provning sker.The test specimens must be kept in normal laboratory conditions for min. 16 hours and max. 4 months before testing.3Provning3TestingProvkroppen fastsätts i en dragprovmaskin och utsätts för minst fem dragningar i följd till samma distans s
9、om beräknat prov för att reducera Mullineffekten. Därefter nollställs kraftmätaren medan provkroppen är utsatt för en svag dragkraft, exempelvis 10 N.The test specimen is fixed in a tensile test apparatus and is exposed to at least 5 pulls in a row to the same dist
10、nace as for a calculated test to reduce the Mullin-effect. Then the strength indicator is set to zero while the test specimen is exposed to a slight traction force, e.g. 10 N.Dragning utförs sedan med en hastighet av 25 ± 5 mm/min till önskad skjuvning.Pulling is then carried out at a
11、 rate of 25 ± 5 mm/min till the shear required is obtained.4Beräkning och angivande av resultat4Calculation and reporting of resultsSkjuvspänningen uttryckt i Pascal (1 Pa = 1 N/m2) beräknas genom att dividera pålagd kraft med bunden yta (2x20x25x10-6 m2).Shear stress expres
12、sed in Pascal (1 Pa = 1 N/m2) is calculated through division of the force put on by the bonded area (2x20x25x10-6 m2).Skjuvtöjningen beräknas genom att dividera halva den aktuella deformationen av provkroppen med gummielementens tjocklek, 8 mm (samma längdenhet).The shear strain is ca
13、lculated through division of half the deformation in question of the test sepcimen by the sheared thickness of the rubber part, 8 mm (the same length unit).Skjuvmodulen är kvoten mellan skjuvspänning och skjuvtöjning.The shear modulus is equal to the quotient between shear stress and
14、shear strain.I provningsrapporten anges skjuvspänningen i kPa.The shear stress is stated in kPa in the test report.5Rapport5ReportProvningsrapport ska innehålla uppgift om:The test report shall include information about:a.materialbeteckning och -ursprunga. material designation and its orig
15、inb.betingelser vid provkroppstillverkningenb.process stipulations of the test piecesc.tillverknings och provningsdatumc.manufacturing and testing datesd.konditionerings- och provningsklimatd.conditioning and testing climatee.resultat och kommentarere.results and commentsf.avvikelser från stand
16、ardenf.divergences from standardÄndringar från föregående utgåvaChanges from previous issueStandarden är, för nykonstruktion, ersatt av ISO 1827.This standard is, for new design, replaced by ISO 1827.Dimensioner i mmDimensions in millimetersFig 1ProvkroppTest piece*;