模具DFM常用中英文对照.docx

上传人:scccc 文档编号:14020820 上传时间:2022-01-30 格式:DOCX 页数:3 大小:16.33KB
返回 下载 相关 举报
模具DFM常用中英文对照.docx_第1页
第1页 / 共3页
模具DFM常用中英文对照.docx_第2页
第2页 / 共3页
模具DFM常用中英文对照.docx_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

《模具DFM常用中英文对照.docx》由会员分享,可在线阅读,更多相关《模具DFM常用中英文对照.docx(3页珍藏版)》请在三一文库上搜索。

1、DFM常用中英文对照1、这个红色面在前模方向/后模方向/行位方向有倒扣.This red surface is undercut at cavity side / core side / slider side.2、这些红色面在前模方向/后模方向/行位方向有倒扣.These red surfaces are undercut at cavity side / core side / slider side.3、产品的这个位置太小,导致模具在前模方向/后模方向/行位方向有薄钢位.This position is too small and it will bring the thin steel

2、 at cavity side / core 万I河一 . , side / slider side. % I: y f j4、这些红色线是前后模/镶件/行位/斜顶分型线. , /|二.IThese red lines are the parting line of cavity and core / insert / slider / lifter.5、此产品使用推板/推块顶出.Use the stripper plate / ejector block to eject this part.6、前模/后模斜内行位.Inner angle slider at cavity / core si

3、de.7、为了简化模具结构建议改变此处出模方向.Suggest to change the draft direction of this position to make the moldstructure simply.8、最终的进胶位置根据模流分析.Finally gate position according the mold flow analysis.9、斜顶与后面的柱位空间太小,斜顶在运动时会干预到柱子,请考虑移动这个柱 子的位置.This lifter intervene with the pole during ejection, please consider changi

4、ng the position of the pole.10、此处有薄钢位,强度缺乏而且不容易冷却.The strength of this area is too weak and it is hard to cool because the thin steel.11、此处有尖角,填充困难.Ej JIt is hard to fill for this area because the sharp feature.二二- .12、此处料位太厚,会有缩水,建议减胶改善.J P J We suggest to reduce some wall thickness to avoid the si

5、nk mark for this position.X J jr ;-i II13、此处的行位夹线在外观面上,请确认是否接受?Please confirm whether it is acceptable to have a slider line on the visible surface?14、建议加大拔模角,以便脱模顺利.We suggest to enlarge the draft angle to help release the tool.15、如果分型面此处,模具上会有尖角和刀口,对模具寿命有影响.There are sharp edges if we set the part

6、ing line here, it will reduce the tool life.16、此处料厚段差很大,成品外表会有应力痕,建议修改如图示.The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown.17、此大行位上有小行位,开模时小行位需先退,大行位做延时,合模时那么相反The small slider is inside the big slider, when the mold open,

7、 the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary.18、此处需做强顶.This position need to force ejection.19、由于此处没有足够空间下热咀,所以需做一个柱子进胶.丁 J 1This position need to make a pole for gating because there have no enoughP space for hot sprue.J?20、沾模,stick

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 社会民生


经营许可证编号:宁ICP备18001539号-1