《16x16led点阵滚动汉字显示设计.docx》由会员分享，可在线阅读，更多相关《16x16led点阵滚动汉字显示设计.docx（8页珍藏版）》请在三一文库上搜索。
1、F面给大家介绍下我制作的16*16led点阵设计，希望与各位电子爱好者共同讨论，共同进步。下图是电路图连接图EHl l.=磔最电F (tkxitca兄密控的嬲Gi- &任蜃-T为凝电平乐 热. G G1必漳群为低阳斗才能用ff芯片.国”策辑车岐小强:小 )任意电平徐二酰无玷据瓦莅费d引蚓说嗯M1 t3-l7.输出端.(outputs (active LOW) 2； Gn通源理 t ground (C . ) tf 使一曾，甫 低电平/咫(enable mpi/s auive LOW)20 2询址看入船(addrecs npurs)24：1CC电源正(f. jbiiivt sup.I, Ydia
2、gei鳍编推主隹地址全能输入对应输出表国”策辑率岐h -高电干(HIGH village亡1L = ,照户(lCA- vlia3e leveD1=可意电平(dont ca)兄要挽海精GK导任图一个为菽电干QK G您疯邯为你电平才能?t作芯片匚、口任意电斗箱、舐无滚动显示C程序如下#include #include #define uchar unsigned char#define uint unsigned intchar code YD=0x01,0x00,0x01,0x00,0x7F,0xFC,0x03,0x80,0x05,0x40,0x09,0x30,0x31,0x0E,0xDF,0x
3、E4,0x00,0x80,0x01,0x00,0x7F,0xFE,0x01,0x00,0x01,0x00,0x01,0x00,0x05,0x00,0x02,0x00,/*季*/0x20,0x40,0x30,0x40,0x24,0x4C,0x42,0x70,0xFF,0x44,0x42,0x46,0x00,0x7C,0x7E,0x00,0x42,0x40,0x7E,0x4C,0x42,0x70,0x7E,0x40,0x42,0x44,0x42,0x46,0x4A,0x3C,0x44,0x00，雄*/0x00,0x00,0x0F,0xF0,0x08,0x10,0x0F,0xF0,0x08,0x10
4、,0x0F,0xF0,0x00,0x00,0xFF,0xFE,0x01,0x00,0x09,0x00,0x09,0xF8,0x09,0x00,0x01,0x00,0x01,0x00,0x02,0x80,0x02,0x40,0x04,0x20,0x09,0x18,0x11,0x0E,0x61,0x04,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0X01,0X00,0X01,0X00,0X01,0X00,0X00,0X00,/*个*/0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0X01,0X00,0XFF,0XFE,0X01
5、,0X00,0X02,0X80,0X02,0X80,0X02,0X40,0X04,0X40,0X04,0X20,0x08,0x10,0x10,0x18,0x20,0x0E,0x40,0x04,/*状*/0X08,0X20,0X08,0X20,0X08,0X20,0X4B,0XFE,0X4A,0X22,0X4A,0X22,0X4A,0X22,0X4A,0X22,0X4A,0X22,0X4A,0X22,0X4A,0X22,0X12,0X2E, 0x12,0x24,0x20,0x20,0x40,0x20,0x80,0x20,/*帅*/0X00,0X00,0X7F,0XFC,0X00,0X10,0X1F,0X90,0x10,0x90,0x1F,0x90,0x10,0x90,0x00,0x04, 0xFF,0xFE,0x00,0x10,0x1F,0x90,0x10,0x90,0x1F,0x90,0x10,0x90,0x00,0x50,0x00,0x20,/*哥*/;void delay(uint z)uint x,y;for(x=z;x0;x-)for(y=110;y0;y-);main()int i,t,k=0;while(1)for(t=0;t5;t+)/t 的值越小，滚动的速度就越快for(i=0;i112) k=0;)有什么问题可能联系版主，关注微博即可联系。本人新浪微博地址: