《不锈钢焊接工艺评定报告及指导书PQR&WPS FOR STAINLESS STEEL WELDING.doc》由会员分享，可在线阅读，更多相关《不锈钢焊接工艺评定报告及指导书PQR&WPS FOR STAINLESS STEEL WELDING.doc（5页珍藏版）》请在三一文库上搜索。
1、不锈钢焊接工艺评定报告及指导书PQR&WPS FOR STAINLESS STEEL WELDING目 录1概述 General22储罐一览表Basic Date Sheet of The Steel Plate23焊接工艺评定报告PQR24焊接工艺指导书WPS35附表Attachments4 1 概述 General本程序制定了所有AA罐区不锈钢储罐的焊接工艺评定报告及焊接工艺指导书。适用于t 12mm。This procedure covers Welding Procedure Specification(WPS) and Procedure Qualification Reports(
2、PQR) applied in AA Petrochemical Intermediate and Product Stainless Steel Tank Project. It is applicable for stainless steel plates with thickness t12mm.本程序适用于AA罐区不锈钢储罐焊接。The procedure is applicably adopted to conduct the welding of AA Petrochemical Intermediate and Product Tank.2 储罐一览表Basic Date Sh
3、eet of The Steel Plate 序号Serial No.储罐编号Storage tank item No.储罐名称Storage tank name储罐直径与高度（m）Storage tank Diameter and Height(m)材质Material 底板 Bottom Plate顶板Roof Plate(mm)壁板 Shell Plate边缘板Annular Plate(mm)中幅板 Medium Plate(mm)SS304(mm)SS316(mm)1404环氧丙烷储罐Finished PO12.5x11SS304T=10SS304T=8SS304T=4.5SS304
4、T=6162405环氧丙烷储罐Finished PO12.5x11SS304T=10SS304T=8SS304T=4.5SS304T=6163416DNPB储罐DNPB storage 4x7SS316T=6SS316T=6SS316T=5SS316T=6414环氧丙烷储罐Propylene Oxide22.5x18SS316T=10SS316T=6SS316T=4.5SS316T=618515环氧丙烷储罐Propylene Oxide22.5x18SS316T=10SS316T=6SS316T=4.5SS316T=6182 焊接工艺评定报告 Procedure Qualification R
5、eport (PQR)2.1 焊接工艺评定报告编号 Welding procedure qualification report numbering2.1.1 CC-PQR-007材质SS304 =6mmMaterial焊接材料：A102Welding material焊接方法：SMAW Welding method 2.1.2 CC-PQR-008材质SS316 =6mmMaterial焊接材料：A202Welding material焊接方法：SMAW3 焊接工艺指导书WPS Welding Procedure Specification3.1 焊接工艺评定指导书编号Welding pro
6、cedure specification numbering3.1.1 XXX-P8-A-Lh-07XXXXXX注：以下的WPS编号与上述内容相同。Note: undering method of following WPS is same as description above.材质SS304 Material适用厚度范围1.5t12mmApplicable range焊接材料：A102Welding material焊接方法：SMAWWelding method支持此焊接工艺指导书的焊接工艺评定报告为CC-PQR-001 This WPS is supported by PQR CC-P
7、QR-001.3.1.2 CC-P8-A-Lh-08材质SS316 Material适用厚度范围1.5t12mmApplicable range焊接材料：A202Welding Material焊接方法：SMAWWelding method支持此焊接工艺指导书的焊接工艺评定报告为CC-PQR-0024 附表 Attachments4.1 焊接工艺评定报告及焊接工艺指导书PQR&WPSWelding Procedure Specification and Welding Procedure Quailfication Report4.2 试板材质质量证明书Qualification certificate of test pieces4.3 焊材质量证明书Qualification cerficates of welding material Page 5 of 4 PQR&WPS FOR STAINLESS STEEL WELDING