《1039高速外齿圈样件检验报告.doc》由会员分享，可在线阅读，更多相关《1039高速外齿圈样件检验报告.doc（4页珍藏版）》请在三一文库上搜索。
1、DABG-ZB-91注：粗线框内由东安动力填写，本报告一式四联。区 分样品种类送检日期： 年 月 日判定日期： 年 月 日样件检验报告新开发件半 成 品设计变更件成 品工程变更件改进产品关键重要一般 更改单日期： ；更改单编号： ；图面版本号：供方：重庆市江汇机械有限责任公司 (第 1 次送样)样品数量：件 试生产产量：机型：DABS10-4 件号：BS10-4-1701039 件名：高速外齿圈 样品重量： 170 g报告内容：尺寸检验 材质报告 性能试验 耐久试验 统计资料 外观件报告 其它送审理由：新开发件样件标识方法及编号使用材料核准审核填表20CrMnTi-GB/T3077-1999东
2、安综合判定核准审核填表合格判定内容：条件合格不合格简图及说明：按规范要求项目所作成之材料、成分、物性、性能试验等报告难以记载本报告以任意格式附纸于后。粗线框内由DA填写。检 验 报 告（续页）DABG-ZB-91注：粗线框内由东安动力填写机型：DABS10-4 件号：BS10-4-1701039 名称：高速外齿圈序号检验项目规 格12345678910判定垂直度0.150.130.140.130.120.140.130.130.140.130.130.1320.000042长度6.950.076.906.926.966.946.926.926.966.986.926.946.9360.0005
3、43平行度0.10.360.580.610.340.330.470.490.440.510.390.4520.08644平行度0.050.040.030.040.030.040.040.030.040.020.040.0350.000055厚度2222.0621.9621.9222.0422.0421.9221.9821.9622.0622.0421.9980.002846槽宽8.10.18.168.068.028.048.18.168.088.048.128.108.0880.002187深度1.80.071.821.761.801.841.781.841.841.781.801.821.8
4、080.000748倒角C0.81.20.921.060.940.820.960.981.101.121.120.880.990.010029滑块槽深度28.1828.2628.3428.2028.3028.3428.2228.3628.3228.2828.3028.2920.002510孔径57.857.9057.7257.8657.7857.9457.8657.7457.9257.6857.7857.8180.0073211孔径6262.1861.9061.9862.0862.0462.1662.0661.9461.9662.0862.0380.0077212外径66.266.1666.0
5、866.0666.0866.1466.0466.1866.1266.1066.0666.1020.0019613同轴度1.00.970.930.940.850.900.940.970.900.950.910.9260.0012214圆弧R32.953.153.043.032.972.953.053.143.022.913.0210.0057115倒角1010.39.5109.710.110.710.210.19.710.310.060.112416厚度30.43.23.122.82.763.063.362.842.662.962.902.9660.0462417倒角C44.063.924.16
6、4.004.163.963.984.064.084.084.0460.0058418内花键小径540.254.0254.0653.8653.9854.0254.1853.9454.1654.0253.8854.0120.0099419圆度0.10.960.920.940.940.980.940.960.900.880.920.9340.0008检 验 报 告（续页）DABG-ZB-91注：粗线框内由东安动力填写机型：DABS10-4 件号：BS10-4-1701039 名称：高速外齿圈序号检验项目规 格12345678910判定20粗糙度Ra1.61.31.370.91.00.951.41.3
7、81.521.21.361.2380.0471421拨叉槽直径6261.9661.8461.8861.9461.9261.8661.8661.9061.9461.8861.8980.0014822外径7272.0671.9471.8671.2271.8871.9272.1872.1271.9672.0871.9920.06523滑块槽长度5.25.165.285.225.065.245.185.185.245.165.265.1980.0037224滑块槽过度圆弧R0.51（两处）0.830.610.730.780.900.570.660.610.850.930.7470.0152225滑块槽
8、过度圆弧R0.51（两处）0.690.730.790.950.680.640.630.840.910.650.7510.0120726滑块槽粗糙度Ra3.22.583.102.032.462.873.112.972.732.672.142.6660.1254627滑块槽斜度1202120.1119.3121.3118.8120.7121.3119.6120.4119.8121.5120.280.763628拨叉槽倒角C0.3（两处）0.320.280.280.320.280.30.30.320.320.280.30.0003229拨叉槽宽粗糙度Ra0.8（两侧）0.720.650.780.51
9、0.630.680.540.710.670.520.6410.0074930拨叉槽底部粗糙度Ra6.35.14.73.86.15.94.35.94.35.64.75.040.578431倒锥角度313.12.72.93.62.33.13.42.92.82.72.950.124532倒锥角粗超度Ra3.22.52.11.72.62.53.13.03.12.82.82.620.181633过度值00.50.320.260.280.340.300.300.260.280.280.320.2940.0006434倒锥底部角度6059.260.3859.460.3260.0860.159.8659.66
10、60.3660.2859.9640.1593435锁止角角度610.560.5561.0861.0560.8661.3061.3561.4060.7860.8661.3961.0620.0785236锁止角粗超度Ra6.35.85.66.16.24.26.05.25.86.14.75.570.402137倒锥长度50.55.14.84.85.15.04.95.05.35.34.85.010.032938锁止角深度0.2max0.080.120.080.140.120.100.120.080.100.120.1060.0004检 验 报 告（续页）DABG-ZB-91注：粗线框内由东安动力填写机
11、型：DABS10-4 件号：BS10-4-1701039 名称：高速外齿圈序号检验项目规 格12345678910判定39锁止角圆弧2.5max2.12.42.12.22.32.02.42.12.02.22.180.019640锁止角夹角22.52.292.362.332.402.182.242.392.452.242.262.3140.0066441锁止角深度0.50.420.380.310.450.420.370.360.410.400.450.3970.016842两锁止角交线宽0.3max0.250.240.280.260.240.160.280.180.200.210.230.001
12、5243标识处定位尺寸55.15.125.145.05.105.125.125.105.125.105.1020.0012344标识处宽度0.80.760.720.740.720.720.700.740.760.700.720.7280.004245标识处深度0.20.220.180.200.220.180.220.220.180.180.180.1980.0003646内花键大径58.20.258.2458.0858.3658.1258.1058.2858.3258.3058.0858.2458.2120.0103447内花键棒间距50.31550.16550.23550.29550.3050.21550.2550.30550.17550.1650.24550.23450.0027648内花键综合公差0.050.0420.0310.0350.0360.0350.0450.0400.0470.0390.0340.03840.0000249渗碳深度0.30.850硬度HRA80845120CrMnTi组成成分C:0.170.23Cr:11.3Mn:0.81.1Ti:0.040.1