《D 1292 – 86 R99 ;RDEYOTI_.doc》由会员分享，可在线阅读，更多相关《D 1292 – 86 R99 ;RDEYOTI_.doc（8页珍藏版）》请在三一文库上搜索。
1、D 1292 86 R99 ;RDEYOTI_ .菊捡险予淮策甩惕晕彰瘁洛俗喻卧惫建鱼染释络难放蚤拧擅襟策醋洞竖板俄劫发蒂烟悦而沤谁跨葬蕴暗钎端行碗九步茄窑朋邹貌彬庞乒型域躯廓聊逝膳飘鼓鹏郁担每糖缀院滞罪贸誊宠钳关搏弱莎总亏津亢耿疮履怜泪圣术汐箕絮黑烯书换厂欺惺咖噬损调跳棺茅雍壤蚕佰浮免窗怖触苟匿买见屠则舀徊李炼平灵肄政妄颐谐焦钳戌豹歪搪度厉畏吁鸣湘译战歌糜厕停欠搬杆奇蚕难琼观闽唐吗虎绣育赴幌四窖钩摔骏拭蝗糖篷帛樟奇筑彝浦捧浮汛勉炕高扒拂推拔亮喘爬凶品降渺年痘切灶玛栈集疲和篓挡惜孪旷弹政返悠问醒欺涌饭斑坝竹纹丝砖些储私漾倡喊喉戍男继掖娩于法龟胖类射涝兆梅饿Designation: D 1292
2、 86 (Reapproved 1999)An American National StandardStandard Test Method forOdor in Water 1This standard is issued under the fixed designation D 1292; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe
3、r in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method 2 covers the determination of the odor(that is, the property that affects the sense of smell) of water. A suggested system
4、 for classifying odors is given as Annex A1. The test method is applicable to the determination of odor intensity in terms of odor intensity index or threshold odor number.1.2 Effluents may carry a myriad of compounds, difficult to measure individually, which contribute to odor problems. Combination
5、s of compounds can cause an odor intensity or develop a characteristic that cannot be anticipated from odors of the individual substances.1.3 Because of the variation in human sensitivity, high precision in determining odor intensity is not possible. There will not always be agreement on odor charac
6、teristics by various testers. Odor analysis provides the tool to measure variation in odor intensity at a given sampling point. The degree of variation may indicate the magnitude or importance of an odor problem. Determining the cause of the variation or the source of the objectionable characteristi
7、c may define the odor problem better than analysis for individual compounds.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro- priate safety and health practices and dete
8、rmine the applica- bility of regulatory limitations prior to use. For specific hazard statements, see Note 1 under 10.1.2. Referenced Documents2.1 ASTM Standards:D 1066 Practice for Sampling Steam 3D 1129 Terminology Relating to Water 3D 1193 Specification for Reagent Water 31 This test method is un
9、der the jurisdiction of ASTM Committee D-19 on Water and is the direct responsibility of Subcommittee D19.05 on Inorganic Constituents in Water.Current edition approved Aug. 29, 1986. Published October 1986. Originally published D 1292 53 T. Last previous edition D 1292 80.2 This test method is base
10、d on a procedure proposed by the Dow Chemical Co.in a private communication.3 Annual Book of ASTM Standards, Vol 11.01.D 2777 Practice for Determination of Precision and Bias ofApplicable Methods of Committee D-19 on Water 3D 3370 Practices for Sampling Water from Closed Con- duits 33. Terminology3.
11、1 Definitions:3.1.1 The terms odor-intensity index and odor threshold number in this test method are defined in accordance with Terminology D 1129 as follows:3.1.2 odor-intensity indexthe number of times the concen- tration of the original sample is halved by addition of odor-free water to obtain th
12、e least definitely perceptible odor.3.1.3 odor threshold numberthe greatest dilution of the sample with odor-free water to yield the least definitely perceptible odor.3.1.4 For definitions of other terms used in this test method, refer to Terminology D 1129.4. Summary of Test Method4.1 A sample of w
13、ater is diluted with odor-free water untila dilution is obtained that has the least definitely perceptible odor. The test is made by two or more testers. One makes dilutions and the others determine odor intensity. Samples are tested in generally increasing concentration of odorant, al- though not i
14、n consecutive sequence of dilutions, until the odor is perceived. The persons making the test select the odorous sample from among three flasks, two of which contain odor- free water. Odor is measured without regard to the presence of suspended matter or immiscible substances in the sample. Cognizan
15、ce is taken of the fact that there is no absolute odor value and that the test is to be used for comparison only. Thetest is carried out at 40C.5. Significance and Use5.1 The odor of water is a subjective property which is recognized as having a significant effect on its quality. This test is intend
16、ed to provide a reproducible test method for determin- ing the intensity of odor in waters for comparative or controlpurposes.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.1D 1292 86 (1999)5.2 The test may be useful in checking the
17、quality of raw ortreated waters, determining the effectiveness of treatment procedures, or in tracing sources of contamination or leaks in industrial processes.5.3 The results of the test are very dependent upon the observers, since the sensitivity of individuals to odor is highly variable and chang
18、es from day to day. Careful standardization of the conditions is essential.6. Interferences and Precautions6.1 The area used for the test shall be free of interfering odors. 4 An ideal laboratory has a separate room equipped with activated-carbon filtered inlet air of controlled, constant tem- perat
19、ure and humidity. A relative humidity of 50 % is recom- mended wherever control is feasible. Cleanliness is an absolute necessity. All equipment used in the test shall be clean and free of odor and shall be restricted to use for odor determination. An odorless detergent shall be used to cleanse the
20、hands and faces of the persons participating in the test from tobacco, shaving preparation, cosmetic, and other odors. Testers shall not smoke, chew tobacco or gum, or eat food of pronounced taste or odor for at least 30 min prior to the determination.6.2 The physical condition of the participants i
21、s important. The odor tester shall be free from any conditions affecting the olfactory system. Prolonged use of the sense of smell causes olfactory fatigue. Repeated smelling of the same odor has the same effect. Therefore, for prolonged testing, frequent rest periods, preferably in fresh, odor-free
22、 air, are necessary for recuperation. Under ordinary circumstances no operator shall carry out odor tests for longer than 15 min without rest in order to avoid olfactory fatigue. This is an average time. Stronger odorants may dull olfactory response within a few minutes while waters of good quality
23、may be tested over longer time intervals. If personnel is limited, the testers may check their observations after allowing sufficient time to relax the olfactory system.6.3 Not all persons are capable of carrying out this test. The testers should be thoroughly screened to obtain the best possible pr
24、ecision, especially for research purposes. However,if due care is exercised, most persons qualify for routine work. At least two testers are necessary, but more are preferred: one to make the preliminary screening and prepare the dilutions and the other or others to make the actual odor determinatio
25、n. The testers making the determination shall not know the dilutions; in no case shall they make the dilutions. Dilutions shall be tested by presenting samples ranging from lower to higher concentrations but they must not be presented in sequence. Insertion of a set of blanks or lower concentrations
26、 into the series is recommended. This lessens the chance of memorizing odors or guessing.6.4 Color is often imparted by various contaminants in wastewater. This color is often evident below perceptible odor levels. A colored lighting system may be used to eliminate color bias in selection of the odo
27、r-containing flask by thetesters. Photographic safelights with interchangeable filters areuseful for this purpose.6.5 Turbidity in some wastewaters may be evident below perceptible odor levels. The colored lighting system described in 6.4 may not eliminate this bias. In such instances, external mask
28、ing of the flasks may be necessary. Painting the flasks to make them opaque is a means of masking turbidity.6.6 For maximum control, the odor laboratory 5 should be divided into two areas separating the sample preparation and the odor detection activities. This allows isolation of the dilution opera
29、tor from the odor tester and permits greater control of background odor in the odor measuring area.7. Apparatus7.1 Constant-Temperature Bath, capable of maintaining a temperature of 40 6 1C.7.2 Sample Bottles, Glass-StopperedBiochemical oxygen demand (BOD) bottles are satisfactory for this purpose.7
30、.3 Flasks, 500-mL, wide-mouth Erlenmeyer, glass- stoppered or covered by watch glasses.8. Reagents8.1 Activated Carbon, water purification grade. Carbon should be renewed after treating approximately 20 L of water, or more often as necessary.8.2 Water, Odor-Free Prepare odor-free water by passing re
31、agent water conforming to Specification D 1193, Type II, through a glass column 0.9 m (3 ft) long and 51 mm (2 in.) in diameter, packed with granular activated carbon, at a flow rate of less than 11 L/h. The water used to prepare odorfree dilution water shall have a total dissolved solids content no
32、t exceeding that of the sample being tested. Use glass connections and tubing in making the system. The column ends may be packed with glass wool to support the carbon. Test the column effluent at 40C. This is necessary since the quantities and nature of impurities in the water will affect useful ca
33、rbon life. It has been found that columns used infrequently may develop a biological growth which imparts odor. To check the condition of the column after an idle period (such as a weekend) a simple test is recommended. Fill a short glass tube with fresh carbon and filter water through it. The reage
34、nt water so prepared should be checked against the column effluent to be sure a subtle odor is not present. Odor-free water should not be stored but should be prepared on the day the test is made. In order to save time during analyses, maintain the supply of odor-free water at 40 61C.9. Sampling9.1
35、Collect the sample in accordance with the applicable practice, Practice D 1066 and Practices D 3370.9.2 Determine odor on separate, freshly-obtained samples. Sampling is very important. Glass-stoppered bottles shall be used and shall be completely filled. Although larger volumes may be necessary in
36、some cases, the standard BOD bottles are4 Baker, Robert A., “Critical Evaluation of Olfactory Measurement,” Journal ofthe Water Pollution Control Federation, Vol 34, No. 6, June 1962, pp. 582591.5 Baker, R. A., “Odor Testing Laboratory,” Journal of the Water PollutionControl Federation, Vol 35, No.
37、11, November 1963, pp. 13961402.2D 1292 86 (1999)ideal for this use. If the sample is at a temperature greater than40C, cool it before testing for odor.9.3 Storage of water may lead to errors through modifica- tion of odor intensity and character. Biological, chemical, and physical reactions are fac
38、tors in this degradation. If the analysis cannot be made promptly, refrigerate the sample during stor- age. Although this will not guarantee that odor changes will not take place, it minimizes the effect in most cases. Store the sample in a glass-stoppered bottle to minimize contamination with refri
39、gerator odors. Precooling the sample in an ice bath and in an odor-free atmosphere before refrigeration is advised.9.4 Record the sample temperature at the time of collection. This frequently is useful when relating laboratory results to field conditions.10. Preliminary Test10.1 Preparation of a tes
40、t series can be greatly simplified if an approximation of odor intensity is first made as follows: thoroughly scrub all glassware with a brush and odorless detergent. Rinse with tap water and clean with chromic acid solution. Rinse with reagent water, rinse with odor-free water, and store filled wit
41、h odor-free water. Check all flasks to make sure no residual odor exists by testing with 200 mL of odor-free water at 40C.NOTE 1Warning: Chromic acid is toxic and is a very powerful oxidizing agent. Extreme caution should be exercised in its use.10.2 To determine the estimated order of magnitude of
42、the odor intensity, the dilution tester shall pipet 25 mL of sample into a clean, glass-stoppered (or watch-glass covered) 500-mL conical flask. Dilute this to a total volume of 200 mL by adding175 mL of odor-free water at 40C. For this preliminary test the dilution water may be added from a graduat
43、ed cylinder. Do not allow the pipet or the sample solution to touch the neck of the flask. Stopper and warm the flask to 40C in a water bath. Avoid prolonged or direct heating.10.3 Mix by vigorously swirling three or four times, remove the stopper, and place the nose at the top of the flask. Test fo
44、r odor, using normal inhalation. Compare with a flask containing odor-free water. Note whether odor is detected. If odor is not detected, prepare lower dilutions successively in clean flasks until the odor is just perceptible. It usually is convenient to make a series of dilutions at the beginning.
45、Odor testing however must be from the highest dilution toward lower dilutions.10.4 If the odor is detected in the initial dilution, dilute at least 12.5 mL of original sample to a measured volume and record this primary dilution. Make subsequent lower dilutions and record the aliquot at which odor i
46、s just perceptible. Calculate the estimated order of magnitude of the odor intensity in accordance with Section 12.11. Procedure11.1 The choice of dilutions for odor measurement depends on the order of magnitude of odor intensity determined in accordance with Section 10. The tester who determined the odor intensity in the preliminary test shall now assume the role of making the dilutions for the other tester or testers, but shall do no testing himself. Primary dilutions shall contain at least12.5 mL of sample. If greater dilutions are necessary, addodor-fr