《【BS英国标准word原稿】BS EN 1360-2005 Rubber and plastic hoses and hoseassemblies for measured fuel dispensing systems — Specification.doc》由会员分享，可在线阅读，更多相关《【BS英国标准word原稿】BS EN 1360-2005 Rubber and plastic hoses and hoseassemblies for measured fuel dispensing systems — Specification.doc（35页珍藏版）》请在三一文库上搜索。
1、 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。BRITISH STANDARDBS EN1360:2005Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems SpecificationThe European Standard EN 1360:2005 has the status of aBritish StandardICS 75.200; 23.040.70 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模
2、糊、乱码等情况，请大家通过论坛消息与我联系。BS EN 1360:2005National forewordThis British Standard is the official English language version of EN 1360:2005. It supersedes BS EN 1360:1997 which will be withdrawn on 11 November2005.The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber a
3、nd plastic tubing, hoses and hose assemblies, which has the responsibility to:aid enquirers to understand the text;present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed;monitor related international an
4、d European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Ca
5、talogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its c
6、orrect application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 28, an inside back cover and a back cover.The BSI copyright notice displayed in
7、this document indicates when the document was last issued.Amd. No.DateCommentsThis British Standard was published under the authority of the Standards Policy and Strategy Committeeon 29 September 2005 BSI 29 September 2005ISBN 0 580 46187 4Amendments issued since publicationEUROPEAN STANDARD NORME E
8、UROPENNEEUROPISCHE NORMEN 1360May 2005ICS 75.200; 23.040.70Supersedes EN 1360:1996English versionRubber and plastic hoses and hose assemblies for measured fuel dispensing systems - SpecificationTuyaux et flexibles en caoutchouc pour distribution mesure de carburants - SpcificationZapfstellenschluche
9、 und -schlauchleitungen aus Gummi und Kunststoff - AnforderungenThis European Standard was approved by CEN on 15 March 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard wit
10、hout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language m
11、ade by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany
12、, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMI T EUROP EN DE NORM AL IS AT ION EU RO PISCHE S KOM I T EE FR NO RMUN G
13、Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 1360:2005: EEN 1360:2005 (E)ContentspageForeword.41Scope .52Normative references .53Terms and definitions .64Classification.6
14、5Materials and construction .66Pressure requirements.67Dimensions and tolerances .77.1Internal diameters and bend radii .77.2Minimum thickness of lining and cover .77.3Concentricity .77.4Tolerance on cut lengths .78Physical properties.78.1Compounds .78.2Finished hose .98.3Hose assembly .109End fitti
15、ngs .1010Type tests .1111Frequency of testing .1112Marking .1112.1Hoses .1112.2End fittings .1212.3Hose assemblies .12Annex A (normative) Test method for determination of low temperature resistance at 30 C (for normal temperature class) and 40 C (for low temperature class) .13A.1Test piece .13A.2App
16、aratus .13A.3Test method.13Annex B (normative) Method for the determination of adhesion between components .15B.1Dry adhesion .15B.2Adhesion after contact with fuel .15Annex C (normative) Test method for the determination of low temperature flexibility .16C.1Test piece .16C.2Apparatus .16C.3Test met
17、hod.16Annex D (normative) Test method for the determination of fuel permeation.18D.1Test piece .18D.2Apparatus .1827D.3Test method . 18Annex E (normative) Test method for flammability . 19E.1Test pieces . 19E.2Apparatus . 19E.3Test method . 19Annex F (normative) End-fitting pull-off test . 21F.1Test
18、 piece . 21F.2Apparatus . 21F.3Test method . 21Annex G (normative) Test method for the determination of leakage (leak test) . 22Annex H (normative) Test method for fatigue strength under reversed bending stress (flex test). 23H.1Apparatus and test pieces. 23H.2Test method . 24H.3Test observations an
19、d report . 24Annex I (normative) Test frequency for type tests and routine tests . 25Annex J (informative) Test frequency for production acceptance tests . 27ForewordThis document (EN 1360:2005) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies”, the
20、secretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2005, and conflicting national standards shall be withdrawn at the latest by November 2005.This documen
21、t supersedes EN 1360:1996.WARNING Persons using this European Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any associated with its use. It is the responsibility of the user to establish appropriate safety and he
22、alth practices and to ensure compliance with any national regulatory conditions.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia
23、, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.1ScopeThis European Standard specifies minimum requirements for three types of hoses in
24、 two categories and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of15 % oxygenated compounds).The assemblies are intended for use at ambient temperatures between 30 C and +55 C for normal temperature class and 40 C and +55 C for low te
25、mperature class at a working pressure 16 bar1).2Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any am
26、endments) applies.EN 26801, Rubber or plastics hoses Determination of volumetric expansion (ISO 6801:1983).EN 27326, Rubber and plastics hoses Assessment of ozone resistance under static conditions(ISO 7326:1991).EN 28033, Rubber and plastics hose Determination of adhesion between components (ISO 8033:1991).EN ISO 1307, Rubber and plastics hoses for general-purpose industrial applications Bore diameter