《【AS澳大利亚标准】AS NZS 61347.2.3-2004 Lamp controlgear Part 2.3 Particular requirements for a.c.bn supplied electronic ballasts for fluorescent lamps.doc》由会员分享，可在线阅读，更多相关《【AS澳大利亚标准】AS NZS 61347.2.3-2004 Lamp controlgear Part 2.3 Particular requirements for a.c.bn supplied electronic ballasts for fluorescent lamps.doc（29页珍藏版）》请在三一文库上搜索。
1、AS/NZS 61347.2.3:2004AS/NZS 61347.2.3Australian/New Zealand StandardLamp controlgearPart 2.3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps(IEC 61347-2-3:2000, MOD)The Standard is downloaded from Standard SharingAS/NZS 61347.2.3:2004This Joint Australian/New Ze
2、aland Standard was prepared by Joint Technical Committee EL-041, Lamps and Related Equipment. It was approved on behalf of the Council of Standards Australia on 22 March 2004 and on behalf of the Council of Standards New Zealand on 30 April 2004. It was published on 17 May 2004.The following are rep
3、resented on Committee EL-041:Association of Consulting Engineers, AustraliaAustralian Chamber of Commerce and IndustryAustralian Electrical and Electronic Manufacturers AssociationConsumer Federation of AustraliaElectrical Compliance Testing Association of AustraliaElectrical Regulatory authorities
4、council (Australia)Energy Efficiency and Conservation Authority of New ZealandIlluminating Engineering Society of Australia and New ZealandInternational Accreditation of NZ (IANZ)Ministry of Economic Development, New ZealandKeeping Standards up-to-dateStandards are living documents which reflect pro
5、gress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard
6、, which should include any amendments which may have been published since the Standard was purchased.Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Web Shop at .au or Standards New Zealand web site at www.standards.co.nz and looking up the re
7、levant Standard in the on-line catalogue.Alternatively, both organizations publish an annual printed Catalogue with full details of all current Standards. For more frequent listings or notification of revisions, amendments and withdrawals, Standards Australia and Standards New Zealand offer a number
8、 of update options. For information about these services, users should contact their respective national Standards organization.We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Please
9、address your comments to the Chief Executive of either Standards Australia International or Standards New Zealand at the address shown on the back cover.This Standard was issued in draft form for comment as DR 03556.AS/NZS 61347.2.3:2004Australian/New Zealand StandardLamp controlgearPart 2.3: Partic
10、ular requirements for a.c. supplied electronic ballasts for fluorescent lamps(IEC 61347-2-3:2000, MOD)Originated as AS 3134(Int)1991. Previous edition AS/NZS 60928:2000.Jointly revised and redesignated as AS/NZS 61347.2.3:2004.COPYRIGHT Standards Australia/Standards New ZealandAll rights are reserve
11、d. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.Jointly published by Standards Australia International Ltd, GPO Box 5420, Sydney, NSW 2001 and Standards New Zealand, Pri
12、vate Bag 2439, Wellington 6020ISBN 0 7337 5966 1iiiThe Standard is downloaded from Standard SharingPREFACEThis Standard was prepared by the Joint Standards Australia/Standards New Zealand CommitteeEL-041,LampsandRelated Equipmentto supersedeAS/NZS 60928:2000, Auxiliaries for lampsA.C. supplied elec
13、tronic ballasts for tubular fluorescent lampsGeneral and safety requirements. In Australia, this Standard will co-exist with AS/NZS 60928 until 30December 2006, on which date AS/NZS 60928 will be withdrawn.The objective of this Standard is to specify particular safety requirements for electronic bal
14、lasts associated with fluorescent lamps.This Standard is an adoption with national modifications and has been reproduced from IEC 61347-2-3:2000, Lamp controlgear Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps, and has been varied as indicated to take a
15、ccount of Australian/New Zealand conditions.Variations to IEC 61347-2-3:2000 are indicated at the appropriate places throughout this standard. Strikethrough (example) identifies IEC text, tables and figures which, for the purposes of this Australian/New Zealand Standard, are deleted. Where text, tab
16、les or figures are added, each is set in its proper place and identified by shading (example). Added figures are not themselves shaded, but are identified by a shaded border.This Standard is a section of Part 2 of AS/NZS 61347 Lamp controlgear. Currently this Series consists of the following parts.
17、Additional parts will be added from time to time.AS/NZS61347.1Part 1: General and safety requirements61347.2.1Part 2.1: Particular requirements for starting devices (other than glow starters)61347.2.2Part 2.2: Particular requirements for d.c. or a.c. supplied electronic step- down convertors for fil
18、ament lamps61347.2.3Part 2.3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps (this Standard)61347.2.4Part 2.4: Particular requirements for d.c. electronic ballasts for general lighting61347.2.5Part 2.5: Particular requirements for d.c. supplied electronic ballast
19、s for public transport lighting61347.2.6Part 2.6: Particular requirements for d.c. supplied electronic ballasts for aircraft lighting61347.2.8Part 2.8: Particular requirements for ballasts for fluorescent lamps61347.2.9Part 2.9: Particular requirements for ballasts for discharge lamps (excluding flu
20、orescent lamps)61347.2.10Part 2.10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes)61347.2.11Part 2.11: Particular requirements for miscellaneous electronic circuits used with luminairesThis Standard is t
21、o be read in conjunction with AS/NZS 61347.1.It is to be noted that AS/NZS 61347.1 has variations from IEC and hence product complying with IEC 61347-1 may not comply with AS/NZS 61347.1.As this Standard is reproduced from an International Standard, the following applies:(a) Its number does not appe
22、ar on each page of text and its identity is shown only on the cover and title page.(b) In the source text this international standard should read this Australian/New ZealandStandard.(c) A full point should be substituted for a comma when referring to a decimal marker. (d)Any French text on figures s
23、hould be ignored.The terms normative and informative are used to define the application of the annex to which they apply. A normative annex is an integral part of a standard, whereas an informative annex is only for information and guidance.vThe Standard is downloaded from Standard SharingCONTENTSP
24、ageIntroduction . v1 Scope . 12 Normative references . 13 Definitions . 14 General requirements . 25 General notes on tests . 26 Classification . 37 Marking . 37.1Mandatory markings. 37.2Information to be provided, if applicable . 38 Protection against accidental contact with live parts . 39 Termina
25、ls, cords and cables . 310 Provisions for earthing . 411 Moisture resistance and insulation . 412 Electric strength .4 13 Thermal endurance test for windings . 414 Fault conditions.4 15 Protection of associated components . 416 Abnormal conditions. 517 Construction .6 18 Creepage distances and clear
26、ances . 619 Screws, current-carrying parts and connections . 620 Resistance to heat, fire and tracking . 621 Resistance to corrosion . 6Annexes . 9Figure 1 Circuit for testing rectifying effect . 7Figure 2 Limits for capacitive leakage current in r.m.s. of HF-operated tubularfluorescent lamps depend
27、ing on duration . 8Figure I.1 Test arrangement . 11Table 1 Relation between r.m.s. working voltage and maximum peak voltage . 4Table J.1 Pulse voltages . 15INTRODUCTIONThis first edition of AS/NZS 61347.2.3, published in conjunction with AS/NZS 61347.1, represents an editorial review of AS/NZS 60928
28、. The formatting into separately published parts provides for ease of future amendments and revisions. Additional requirements will be added as and when a need for them is recognized.This standard, and the parts which make up AS/NZS 61347.2, in referring to any of the clauses of AS/NZS 61347.1, spec
29、ify the extent to which such a clause is applicable and the order in which the tests are to be performed; they also include additional requirements, as necessary. All parts which make up AS/NZS 61347.2 are intended to be self-contained and, therefore, do not include references to each other. However
30、, for the case of emergency lighting lamp controlgear, some cross-referencing has been necessary.Where the requirements of any of the clauses of AS/NZS 61347.1 are referred to in this standard by the phrase ”The requirements of clause n of AS/NZS 61347.1 apply”, this phrase is interpreted as meaning
31、 that all requirements of the clause in question of part 1 apply, except any which are clearly inapplicable to the specific type of lamp controlgear covered by this particular part of AS/NZS 61347.2.viiThe Standard is downloaded from Standard SharingNOTESCOPYRIGHTSTANDARDS AUSTRALIA/STANDARDS NEW Z
32、EALANDAustralian/New Zealand StandardLamp controlgearPart 2.3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps(IEC 61347-2-3:2000, MOD)1 ScopeThis part of AS/NZS 61347 specifies particular safety requirements for electronic ballasts for use on a.c. supplies up to
33、1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in AS/NZS 4782.1 and AS/NZS 60901, and other fluorescent lamps for high-frequency operation.Particular requirements for electronic ballasts with means of protectio
34、n against overheating are given in annex C.Particular requirements for a.c./d.c. supplied electronic ballasts for maintained emergency lighting are given in annex J.Performance requirements are the subject of AS/NZS 60929.2 Normative referencesFor the purpose of this part of AS/NZS 61347, the normat
35、ive references given in clause 2 of AS/NZS 61347.1 which are mentioned in this standard apply, together with the following normative references.IEC 60598-2-22, Luminaires Part 2-22: Particular requirements Luminaires for emergency lightingAS/NZS 61347.1, Lamp controlgear Part 1: General and safety r
36、equirementsIEC 61347-2-7, Lamp controlgear Part 2-7: Particular requirements for d.c. supplied electronic ballasts for emergency lighting*)3 DefinitionsFor the purpose of this part of AS/NZS 61347, the definitions of clause 3 of AS/NZS 61347.1 apply, together with the following:3.1a.c. supplied electronic ballastmains-supplied a.