《【AS澳大利亚标准】AS NZS 60745.2.16-2009 Hand-held motor-operated electric tools—Safety Part 2.16 Particular requirements for tackers.doc》由会员分享，可在线阅读，更多相关《【AS澳大利亚标准】AS NZS 60745.2.16-2009 Hand-held motor-operated electric tools—Safety Part 2.16 Particular requirements for tackers.doc（25页珍藏版）》请在三一文库上搜索。
1、AS/NZS 60745.2.16:2009AS/NZS 60745.2.16:2009IEC 60745-2-16 Ed 2, IDTAustralian/New Zealand StandardHand-held motor-operated electric toolsSafetyPart 2.16: Particular requirements for tackersThe Standard is downloaded from Standard SharingAS/NZS 60745.2.16:2009This Joint Australian/New Zealand Stand
2、ard was prepared by Joint Technical Committee EL-002, Safety of Household and Similar Electrical Appliances and Small Power Transformers. It was approved on behalf of the Council of Standards Australia on 17 March 2009 and on behalf of the Council of Standards New Zealand on 13 March 2009.This Stand
3、ard was published on 29 May 2009.The following are represented on Committee EL-002:Australian Industry GroupAustralian Retailers AssociationBusiness New ZealandConsumer Electronic Suppliers Association, AustraliaConsumers Federation of AustraliaElectrical regulatory authorities, Australia Electrical
4、 Compliance Testing Association Electrical consultantsEngineers AustraliaAssociation of Certification BodiesMinistry of Consumer Affairs, New ZealandNew Zealand Electric Fence Energizer Manufacturers Standards GroupKeeping Standards up-to-dateStandards are living documents which reflect progress in
5、science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which s
6、hould include any amendments which may have been published since the Standard was purchased.Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Web Shop at .au or Standards New Zealand web site at www.standards.co.nz and looking up the relevant St
7、andard in the on-line catalogue.Alternatively, both organizations publish an annual printed Catalogue with full details of all current Standards. For more frequent listings or notification of revisions, amendments and withdrawals, Standards Australia and Standards New Zealand offer a number of updat
8、e options. For information about these services, users should contact their respective national Standards organization.We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Please address y
9、our comments to the Chief Executive of either Standards Australia or Standards New Zealand at the address shown on the back cover.This Standard was issued in draft form for comment as DR 08927.AS/NZS 60745.2.16:2009Australian/New Zealand StandardHand-held motor-operated electric toolsSafetyPart 2.16
10、: Particular requirements for tackersOriginated in Australia as AS C1601959. Previous edition AS/NZS 3160:1996.Jointly revised and redesignated, in part, as AS/NZS 60745.2.16:2009.COPYRIGHT Standards Australia/Standards New ZealandAll rights are reserved. No part of this work may be reproduced or co
11、pied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.Jointly published by Standards Australia, GPO Box 476, Sydney, NSW 2001 and StandardsNew Zealand, Private Bag 2439, Wellington 6020ISBN 0 7337 9068 23The Standard is do
12、wnloaded from Standard SharingCONTENTSFOREWORD.41Scope .62Normative references .63Terms and definitions .64General requirements .75General conditions for the tests .76Void .77Classification .78Marking and instructions .79Protection against access to live parts .810 Starting .811 Input and current .
13、912 Heating .913 Leakage current .914 Moisture resistance .915 Electric strength .916 Overload protection of transformers and associated circuits .917 Endurance .918 Abnormal operation . 1019 Mechanical hazards . 1020 Mechanical strength . 1221 Construction . 1222 Internal wiring. 1223 Components .
14、1224 Supply connection and external flexible cords . 1225 Terminals for external conductors . 1226 Provision for earthing. 1227 Screws and connections . 1228 Creepage distances, clearances and distances through insulation . 1229 Resistance to heat, fire and tracking . 1230 Resistance to rusting . 12
15、31 Radiation, toxicity and similar hazards . 13Annexes . 14Annex K (normative) Battery tools and battery packs . 14Annex L (normative) Battery tools and battery packs provided with mains connectionor non-isolated sources . 15Annex ZZ (informative) Variations to IEC 60745-2-16 Ed 2 for application in
16、 Australiaand New Zealand . 16Bibliography . 175The Standard is downloaded from Standard SharingAUSTRALIA/NEW ZEALAND STANDARDHAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2.16: Particular requirements for tackersFOREWORDThis standard was prepared by the Joint Standards Australia/Standards Ne
17、w Zealand Committee EL-002- Safety of Household and Similar Electrical Appliances and Small Power Transformers to supersede in part AS/NZS 3160:2001, Approval and test specification Hand-held portable tools, 3 years from publication. During this period it is anticipated that regulatory authorities w
18、ill approve tackers to either standard.The objective of this Standard is to provide manufacturers, designers, regulatory authorities, testing laboratories and similar organizations with safety requirements designed to give the user protection against hazards that might occur during normal operation
19、and abnormal operation of the tool and which may be used as the basis for approval for sale or for connection to the electricity supply mains in Australia and New ZealandThis Standard is an adoption with national modifications and contains the full text of the second edition of IEC 60745-2-16, Hand-
20、held motor-operated electric tools Safety Part 2-16: Particular requirements for tackers and has been varied as indicated to take account ofAustralian and New Zealand conditions.This part is to be used in conjunction with AS/NZS 60745.1:2009 and its amendments. The Parts 2 contain clauses to supplem
21、ent or modify the corresponding clauses in this part to provide the relevant requirements for each type of tool.NOTE 1 The following print types are used:requirements: in roman type;test specifications: in italic type;notes: in small roman type.The numbering of clauses, subclauses, notes, tables, fi
22、gures and annexes follows that of IEC60745-2-16 Ed 2.0. To allow for the introduction of additional material by the IEC, the numbers 201 to 300 have been reserved. To allow for additional material to be introduced by Australia and New Zealand, the numbers 301 to 400 are used to number further clause
23、s, subclauses, notes, tables and figures in part 1. Additional annexes are lettered ZA, ZB and so on.This scheme has been introduced to reduce the likelihood of the IEC and Australia and NewZealand using the same identifier for different purposes.The use of the word VOID indicates that the IEC text
24、is not used in Australia or New Zealand. The use of this word also avoids the need to renumber, clauses, notes, tables and figure if an earlier clause, note, table or figure is not used.As this Standard is reproduced from an International Standard, the following applies:(a) Its number does not appea
25、r on each page of text and its identity is shown on the cover and title page only.(b) In the source text this International Standard should read this Australian/New ZealandStandard.(c) A full point substitutes for a comma when referring to a decimal marker.Variations to IEC 60745-2-16 Ed 2.0 are ind
26、icated at the appropriate places throughout this standard. Strikethrough (example) identifies IEC tables, figures and passages of text which, for the purposes of this Australian/New Zealand standard are deleted. Where Australian/New Zealand tables, figures or passages of text are added, each is set
27、in its proper place and identified by shading (example). Added figures are not themselves shaded, but are identified by a shaded border.Variations made to IEC 60745-2-16 Ed 2.0 form the New Zealand variations for the purposes of the IECEE scheme for recognition of testing to standards for safety of
28、electrical equipment (the CB scheme). These variations have been incorporated in the body of the standard. They are listed in Annex ZZ for easy reference.The essential safety requirements in AS/NZS 3820 that could be applicable to tackers are covered by this standard.17The Standard is downloaded fro
29、m Standard SharingHAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2.16: Particular requirements for tackers1 ScopeThis clause of Part 1 is applicable, except as follows:Addition:This standard applies to tackers intended for general use. This standard does not apply to tackers intended for indus
30、trial production applications.2 Normative referencesThis clause of Part 1 is applicable.3 Terms and definitionsThis clause of Part 1 is applicable, except as follows:3.101 tackertool in which energy is applied to loaded fasteners, e.g. metal pins, nails or staples, for the purpose of driving the lat
31、ter into wood, plastic, fabric or similar material3.102actuation systemuse of a trigger, workpiece contact and/or other operating control, separately or in some combination or sequence, to actuate the tool3.103single sequential actuationactuation system in which there is more than one operating cont
32、rol to be activated in a specific sequence to actuate the tool. Additional actuation is possible, when a specific operating control, other than a workpiece contact, is released and re-activated3.104full sequential actuationactuation system in which there is more than one operating control to be acti
33、vated in a specific sequence to actuate the tool. Additional actuation is only possible, when all operating controls are released and re-activated in the same sequence3.105contact actuationactuation system in which there is more than one operating control and the operating controls can be activated in any sequence to actuate the tool. Additional actuation is possible, whenany operating control is released and re-activatedCOPYRIGHT3.106selective actuationactuation system that allows discrete selection of two or