《【BS英国标准word原稿】BS EN 12808-5-2008 Grouts for tiles. Determination of water absorption.doc》由会员分享，可在线阅读，更多相关《【BS英国标准word原稿】BS EN 12808-5-2008 Grouts for tiles. Determination of water absorption.doc（13页珍藏版）》请在三一文库上搜索。
1、 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。BRITISH STANDARDBS EN12808-5:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIGrouts for tilesPart 5: Determination of water absorptionICS 91.100.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 12808-5:
2、2008National forewordThis British Standard is the UK implementation of EN 12808-5:2008. It supersedes BS EN 12808-5:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/539, Ceramic tiles and other rigid tiling.A list of organizations represented on t
3、his committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Licensed Copy: :FULLNA
4、ME, : DATE, Uncontrolled Copy, (c) BSIThis British Standard was published under the authority of the Standards Policy andStrategy Committee on 30November 2008 BSI 2008ISBN 978 0 580 61259 6Amendments/corrigenda issued since publicationDate CommentsBS EN 12808-5:2008EUROPEAN STANDARD NORME EUROPENNEE
5、UROPISCHE NORMEN 12808-5October 2008ICS 91.100.10Supersedes EN 12808-5:2001English VersionGrouts for tiles - Part 5: Determination of water absorptionMortiers de joints pour carrelage - Partie 5: Dtermination de labsorption deauMrtel und Klebstoffe fr Fliesen und Platten - Teil 5: Bestimmung der Was
6、seraufnahmeThis European Standard was approved by CEN on 29 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograp
7、hical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a C
8、EN member into its own language and notified to the CEN Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, I
9、taly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NOR M A L I S A TI ON EUR O P I S C H ES KOM I TEE F R NOR M UNG Management Cen
10、tre: rue de Stassart, 36 B-1050 BrusselsLicensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 12808-5:2008: ELicensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSICont
11、entsPageForeword.31Scope .42Normative references .43Sampling .44Test conditions .45Test materials .46Apparatus .47Mixing of grouts .58Preparation of test specimens .59Conditioning .610Test procedure .611Evaluation and expression of results .612Test report .65BS EN 12808-5:2008EN 12808-5:2008 (E)Lice
12、nsed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIForewordThis document (EN 12808-5:2008) has been prepared by Technical Committee CEN/TC 67 “Ceramic tiles”, the secretariat of which is held by UNI.This European Standard shall be given the status of a national standard, either by publication o
13、f an identical text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be
14、held responsible for identifying any or all such patent rights.This document supersedes EN 12808-5:2001.This document is one of a series of European Standards for ceramic tile adhesives including: EN 1308, Adhesives for tiles - Determination of slipEN 1323, Adhesives for tiles - Concrete slabs for t
15、estsEN 1324, Adhesives for tiles - Determination of shear adhesion strength of dispersion adhesivesEN 1346, Adhesives for tiles - Determination of open timeEN 1347, Adhesives for tiles - Determination of wetting capabilityEN 1348, Adhesives for tiles - Determination of tensile adhesion strength for
16、cementitious adhesivesEN 12002, Adhesives for tiles - Determination of transverse deformation for cementitious adhesives and groutsEN 12003, Adhesive for tiles - Determination of shear adhesion strength of reaction resin adhesives EN 12004, Adhesives for tiles Requirements, evaluation of conformity,
17、 classification and designation EN 12808-1, Grouts for tiles Part 1: Determination of chemical resistance of reaction resin mortars EN 12808-2, Grouts for tiles Part 2: Determination of resistance to abrasionEN 12808-3, Grouts for tiles Part 3: Determination of flexural and compressive strengthEN 12
18、808-4, Grouts for tiles Part 4: Determination of shrinkageEN 12808-5, Grouts for tiles Part 5: Determination of water absorptionAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, B
19、elgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.Licensed Copy: :
20、FULLNAME, : DATE, Uncontrolled Copy, (c) BSI1ScopeThis European Standard applies to all ceramic tile grouts for internal and external tile installations on walls and floors.This European Standard specifies the test method to be used to determine the water absorption coefficient due to capillary acti
21、on when the grout surface contacts the water without any additional pressure. The coefficient is measured by means of prisms.This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles.NOTECeramic tile grouts may also be used f
22、or other types of tiles (natural and agglomerated stones, etc.), where these do not adversely affect the stones.2Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references
23、, the latest edition of the referenced document (including any amendments) applies.EN 196-1:2005, Method of testing cement Part 1: Determination of strengthEN 1067, Adhesives - Examination and preparation of samples for testingEN ISO 15605, Adhesives Sampling (ISO 15605:2000)3SamplingTake a sample o
24、f at least 2 kg of the product to be tested in accordance with EN ISO 15605 and EN 1067.4Test conditionsStandard conditions shall be (23 2) C and (50 5) % R.H. and a speed of air in the working area less than0,2 m/s.5Test materialsCondition all test materials for at least 24 h under standard conditi
25、ons.6Apparatus6.1Three gang mould with ground surfaces, made of steel, used for the preparation of 40 mm x 40 mm x160 mm prisms, in accordance with Clause 4.5 of EN 196-1:2005.6.2Jolting apparatus or jolting table used for the compaction of 40 mm x 40 mm x 160 mm grout specimen, in accordance with C
26、lause 4.6 of EN 196-1:2005.6.3Tray with a flat base, large enough to contain three test specimens.Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI7Mixing of groutsThe amount of water and/or liquid admix required for preparing the cementitious grout shall be as stated by the manufacturer
27、in parts by weight, i.e. liquid to dry powder.Prepare at least 2 kg of the grout in a mixer of the type described in Clause 4.4 of EN 196-1:2005, using the slow speed settings, (140 5) r/min rotation and (62 5) r/min planetary movement.Carry out the following procedure: pour the liquid into the pan;
28、 scatter the dry powder over the liquid; mix for 30 s; take out the mixing paddle; scrape down the paddle and pan within 1 min; replace the paddle and mix for 1 min.Let the grout mature if and as specified in the manufacturers instructions, and then mix for a further 15 s. In the case of reaction re
29、sin grouts follow the manufacturers instructions.8Preparation of test specimensInsert a 1 mm thick, rigid, plastic (e.g. PTFE) or metal divider into each compartment of the mould, approximately in the middle, parallel to the ends.Mould the specimens immediately after the preparation of the grout, wi
30、th the mould firmly clamped to the jolting table.Introduce, using a suitable scoop, the first of two layers of grout into each of the compartments, directly from the mixing bowl. Spread the layer uniformly, then compact using 60 jolts.Introduce the second layer of grout, level and compact with a fur
31、ther 60 jolts.Lift the mould gently from the jolting table, strike off excess of material and smooth the surface with a flat trowel. Wipe off the grout left on the perimeter of the mould. Cover the mould with a glass plate according to EN 196-1.Place the mould, suitably identified, on a horizontal b
32、ase in standard conditions, (23 2) C and(50 5) % R.H.After 24 h carefully remove the specimen from the mould.Keep the demoulded prisms for 27 days in standard conditions leaving a clearance of at least 25 mm on all sides.Prepare six specimens for each grout.9ConditioningThe test units are conditione
33、d for 27 days in standard conditions, (23 2) C and (50 5) % R.H.10 Test procedureAfter 21 days from manufacture seal the side faces by means of a neutral curing silicone sealant so as to be water impermeable.After 28 days from manufacture, weigh, with 0,1 g precision, each test sample and then place
34、 them in the tray, with the upper surface down, immersed in water, 5 mm to 10 mm deep, taking care to prevent the prism faces from coming in contact with each other.Maintain the water level constant by adding water when necessary.After 30 min remove the test samples from water, quickly dry them by b
35、lotting with a dampened cloth and immediately weigh. Replace in the tray and repeat the procedure after 210 min.11 Evaluation and expression of resultsCalculate the water absorption, in grams, after 30 min and 240 min of each sample using the following formula:Wmt= m t - m dLicensed Copy: :FULLNAME,
36、 : DATE, Uncontrolled Copy, (c) BSIwhere:Wmtis the water absorption, in grams;mdis the mass of the dry specimen, in grams;mtis the mass of the specimen after immersion, in grams. Calculate the mean of at least three test samples.12 Test reportThe test report shall provide the following information:a
37、)number, title and issue of this European Standard;b)place and date of sampling;c)type of grout, commercial designation and manufacturer name;d)identification of the test sample;e)handling and storage of samples before testing;f)test conditions;g)date of testing;h)amount of water or liquid used for
38、preparing the grout;i)test results (water absorption, individual and mean values after 30 min and 240 min);j)any other factor that could have influenced the result.BS EN 12808-5:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIThis page has been intentionally left blankLicensed Copy:
39、:FULLNAME, : DATE, Uncontrolled Copy, (c) BSIBS EN12808-5:2008BSI GroupHeadquarters 389Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users