《【BS英国标准】BS EN 751-1-1997 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Part 1.doc》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 751-1-1997 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Part 1.doc（15页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARDSealing materials for metallic threaded joints in contact with1st, 2nd and 3rd family gases and hot waterPart 1. Anaerobic jointing compoundsThe European Standard EN 751-1 : 1996 has the status of aBritish StandardICS 91.140.40; 91.140.60| BS EN751-1 : 1997|NO COPYING WITHOUT BSI PER
2、MISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 751-1 : 1997Committees responsible for thisBritish StandardThe preparation of this British Standard was entrusted to Technical Committee PSE/2, Jointing materials and compounds, upon which the following bodies were represented:Asbestos Information Ce
3、ntre Ltd.British Adhesives and Sealants Association British Compressed Gases Association British Hydromechanics Research GroupChartered Institution of Water and Environmental ManagementEnergy Industries Council Industrial Water Society LP Gas AssociationWater Services Association of England and Wale
4、sThis British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on15 July 1997BSI 1997The following BSI references relate to the work on this standard:Committee reference PSE/2Draft for c
5、omment 94/708883 DCISBN 0 580 27656 2Amd. No.DateText affectedAmendments issued since publicationBS EN 751-1 : 1997ContentsPage Committees responsible Inside front cover National foreword ii Foreword 2Text of EN 751-13BSI 1997iBS EN 751-1 : 1997National forewordThis Part of BS EN 751 has been prepar
6、ed by Technical Committee PSE/2, and is the English language version of EN 751-1 : 1996, Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Part 1: Anaerobic jointing compounds, published by the European Committee for Standardization (CEN).It s
7、upersedes BS 6956 : Part 7 : 1992 which is withdrawn.Cross-referencesInternational standards Corresponding British StandardISO 7-1BS 21 Specification for pipe threads for tubes and fittings where pressure-tight joints are made on the threads (metric dimensions)ISO 228-1BS 2779 Specification for pipe
8、 threads for tubes and fittings where pressure-tight joints are not made on the threads (metric dimensions)BS 5380 Specification for hydraulic port and stud coupling using O-ring sealing and G series fastening threadsEN ISO 2160BS EN ISO 2160 Petroleum products, Corrosiveness to copper. Copper strip
9、 testEN 437BS EN 437 Specification for test gases, test pressure and categories of appliance, for gas appliancesEN 10242BS EN 10242 Threaded pipe fittings in malleable cast ironCompliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document
10、comprises a front cover, an inside front cover, pages i and ii, the ENtitle page, pages 2 to 8, an inside back cover and a back cover.iiBSI 1997EUROPEAN STANDARDEN 751-1NORME EUROPE ENNEEUROPA ISCHE NORMDecember 1996ICS: 21.140; 23.040.80Descriptors: Pipe fittings, gas pipes, water pipes, hot water,
11、 threaded fittings, sealing materials, definitions, specifications, tests, effectiveness, markingEnglish versionSealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Part 1: Anaerobic jointing compoundsMate riaux de tanche ite pour raccords filete
12、 s en contact des gaz de la 1e re, 2e me et 3e me famille et de leau chaude Partie 1: Composition de tanche ite anae robieDichtmittel fu r Gewindeverbindungen in Kontakt mit Gasen der 1., 2. und 3. Familie und Heiwasser Teil 1: Anaerobe DichtmittelThis European Standard was approved by CEN on 1996-1
13、1-24. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained
14、 on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretari
15、at has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Sta
16、ndardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels1996 Copyright reserved to CEN membersRef. No. 751-1 : 1996 EPage 7751-1 1996BSI 1997ForewordThis European Standard has been prepared byTechnical Committee CEN/TC
17、108, Sealing materialsContentsPageand lubricants for gas appliances and gas equipment, the secretariat of which is held by NNI.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1997, and confli
18、cting national standards shall be withdrawn atthe latest by June 1997.This European Standard consists of the followingParts: Part 1: Anaerobic jointing compounds Part 2: Non-hardening jointing compounds Part 3: Unsintered PTFE tapesThis European Standard has been prepared under a mandate given to CE
19、N by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s).According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belg
20、ium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Foreword 2Introduction 31 Scope 32 Normative references 33 Definitions 44 Classification of jointing compounds 45 Requirements 45.1 Re
21、quirements to be met by thejointing compound as received 45.2 Requirements to be met by thejointing compound after assembly 45.3 Re-test 46 Test material and documentation 56.1 Test material 56.2 Test documentation 57 Test methods 57.1 Tests of the jointing compound asreceived 57.2 Test of the joint
22、ing compound afterassembly 58 Marking and Instructions 78.1 Marking on packages 78.2 Instructions 7IntroductionThis European Standard specifies requirements and test methods for anaerobic jointing compounds for metallic threaded joints. These liquid, gellike or pasty sealants cure inside the gap of
23、the threaded joint by the absence of oxygen catalyzed by contact with the metal of the threaded joint. By the curing reaction, which is time and temperature dependent, a polymeric material is formed, which fills the gap andmicro-imperfections of the thread and binds strongly to the metal surfaces th
24、us sealing and bonding the threaded joint.Anaerobic jointing compounds can be formulated to harden to different strength levels. Users of such materials should therefore consult the manufacturers information to ensure that the grade is suitable for the application e.g. the size of the thread, the ma
25、terials of the joints, and whether the joint needs to be dismantled.Since not only the mechanical strength of the threaded joint but also the sealing properties of the anaerobic sealing material are influenced by the preparation of the threads and other factors, the application instructions provided
26、 by the manufacturer of thesealing material should be followed. It is important that only Competent Persons should be working on gas installations.For applications outside the scope of this Standard the manufacturer should be consulted prior to use.It is important to note that threaded joints once f
27、inally assembled should never be adjusted. Where it proves necessary to dismantle the joints, they should be unscrewed completely, cleaned and assembled once again using fresh jointing compound.A universally applicable jointing compound may be used for all gas, potable water, and hot water installat
28、ions.In respect of potential adverse effects of the jointing compounds covered by this European Standard on the quality of water intended for human consumption this Standard provides no information as to whether the jointing compounds may be used without restriction in any of the Member States of th
29、e EU or EFTA. The use and characteristics of the jointing compounds should comply with current regulations, where they exist, depending on the acceptance of verifiable European criteria.1 ScopeThis European Standard specifies requirements and test methods for anaerobic jointing compounds (hereafter
30、referred to as jointing compounds) suitable for sealing threaded metallic joints such as those specified in ISO 7-1. These jointing compounds are for use in contact with 1st family gases (town gas), 2nd family gases (natural gas) and 3rd family gases (liquefied petroleum gases (LPG) not including LP
31、G in the liquid form) and hot water of heating systems according to table 1.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are
32、 listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.ISO 7-1Pipe threads where
33、 pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designationISO 228-1Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designationEN ISO 2160 Petroleum products Corrosiveness to copper Copper strip test(ISO 2160 :
34、 1985, includingCorrigendum 1 : 1993)EN 437Test gases Test pressures Appliance categoriesEN 10242Threaded pipe fittings in malleable cast ironprEN 10255Carbon steel tubes suitable for welding or threadingprEN 12164Copper and copper alloys Rod for free machining purposesTable 1. Application of anaero
35、bic jointing compoundsFluidTemperature rangeCPressure-limit barTypical application1st, 2nd, 3rd family gases1)hot water2)220 to 125up to 13057gas appliances gas equipment installationheating systems1) Some jointing compounds can be used for other applications. For such applications, which are outsid
36、e the scope of this EuropeanStandard, the purchaser should consult the manufacturer.2) Sealing properties and mechanical strength are influenced by various factors such as nature of metal, form, roughness and size of thread, cleanness of the joint from cutting oil, etc. Non-hardening sealing materia
37、ls in the form of e.g. jointing compounds paste are covered by EN 751-2 and in the form of PTFE-tapes are covered by EN 751-3.3 DefinitionsFor the purposes of this European Standard the following definitions apply:3.1 anaerobic jointing compound (referred to hereafter as jointing compound)Sealing ma
38、terial applied as a liquid, gel or paste to the threads (without the addition of sealant supporting bases) which cures inside the gap of the threaded joint in the absence of oxygen and catalysed by metal ions.3.2 gas familyFor further information on types of gases see EN 437.3.3 batchAny quantity of
39、 jointing compound manufactured in a single mix at one time.4 Classification of jointing compoundsThere are two classes of anaerobic jointing compounds suitable for fine (I) and coarse (H) threads accordingto table 2.Table 2. Classification of anaerobic jointing compoundsClassThreadNominal SizeIHISO
40、 7-1 taper/parallel and taper/taperISO 7-1 taper/parallel and taper/taperDN # 10 1)10 DN # 501) Class I anaerobic jointing compounds may also be used for other dimensions when the number of turns of the threadis 7,5 cm-1.5 Requirements5.1 Requirements to be met by the jointing compound as received5.
41、1.1 Visual qualityThe jointing compound shall be of a homogenousliquid to pasty consistency easily applicable to threads. It shall also be free of lumps or other deleterious materials when tested in accordance with the method described in 7.1.1.5.1.2 Chemical stabilityThe jointing compound shall hav
42、e a gel time not less than 5 min at 100 C when tested in accordance with the method described in 7.1.2.5.1.3 Corrosive propertiesThe jointing compound shall not cause corrosion of aluminium, brass, copper, low carbon steel or zinc surfaces when tested in accordance with 7.1.3. The appearance of copp
43、er and brass test strips shall give a classification 3 or less in accordance with EN ISO 2160.5.1.4 Storage propertiesThe storage life of the jointing compound shall be at least one year in its original unopened container when stored at a temperature less than 25 C, indicated and declared by the manufacturer.5.2 Requirements to be met by the jointing compound after assembly5.2.1 Sealing propertiesWhen tested in accordance with the methods described in 7.2.1 the jointing compound shall not disintegrate or flow out of the joint and shall not permit