《【BS英国标准】BS EN 975-1-2009 Sawn timber — Appearance grading of hardwoods Part 1 Oak and beech.doc》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 975-1-2009 Sawn timber — Appearance grading of hardwoods Part 1 Oak and beech.doc（39页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARDBS EN 975-1:2009Sawn timber Appearance grading of hardwoodsPart 1: Oak and beechICS 79.040NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 975-1:2009National forewordThis British Standard is the UK implementation of EN 975-1:2009. It supersedes BS EN 975-1:
2、1996 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/543, Round and sawn timber.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions
3、 of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April2009 BSI 2009ISBN 978 0 580 60399 0Amen
4、dments/corrigenda issued since publicationDate CommentsBS EN 975-1:2009EUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 975-1March 2009ICS 79.040Supersedes EN 975-1:1995English VersionSawn timber - Appearance grading of hardwoods - Part 1: Oak and beechBois scis - Classement daspect des bois feuil
5、lus - Partie1: Chne et htreSchnittholz - Sortierung nach dem Aussehen von Laubholz- Teil 1: Eiche und BucheThis European Standard was approved by CEN on 24 January 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European S
6、tandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, Fre
7、nch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus,
8、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C OM I
9、 T EUR OP EN DE NOR M AL I S ATI ON EUR OP I S C HES KOM I TEE F R NOR M UNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 975-1:2009: EContentsPageForeword.3 1 Scope .4 2 N
10、ormative references .4 3 Terms and definitions .5 4 Method of determination of sawn timber quality.5 4.1 Rules for grading .5 4.2 Grading principles .6 4.2.1 Assessment of the quality .6 4.2.2 Cases of un-edged boards.6 4.3 Criteria to be taken into account .6 4.3.1 General.6 4.3.2 Criteria linked t
11、o the structure of the timber .7 4.3.3 Sawing characteristics .7 4.3.4 Warp .7 4.3.5 Fungal and insect attacks .7 4.3.6 Stains .7 4.3.7 Other characteristics .8 5 Denomination of grades.8 5.1 General.8 5.2 Oak (Q) .8 5.3 Beech (F).9 6 Acceptance of batches.9 6.1 Un-edged boards .9 6.2 Square edged t
12、imber .9 7 Grading rules.9 7.1 Grading face .9 7.2 Un-edged boards .9 7.2.1 Grading area .9 7.2.2 Presence of a solitary feature (only one) . 10 7.3 Strips and square edged timber . 10 7.3.1 Knots . 10 7.3.2 Other features . 10 7.4 Baulks . 10 7.5 Appearance grading Tables. 11 Bibliography . 35 9BS
13、EN 975-1:2009EN 975-1:2009 (E)ForewordThis document (EN 975-1:2009) has been prepared by Technical Committee CEN/TC 175 “Round and sawn timber”, the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical te
14、xt or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by September 2009.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held resp
15、onsible for identifying any or all such patent rights.This document supersedes EN 975-1:1995.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Rep
16、ublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.1ScopeThis European Standard specifies the rules de
17、termining the quality of appearance graded sawn timber. It describes various grades of temperate hardwood rough sawn timber and regularized timber for which it lays down denominations and definitions. It also gives rules for composition and acceptance of batches.This standard gives minimum requireme
18、nts for each grade classification. Sawn timber not included within limits given in this standard may be defined, if necessary, by contract specifications established on the basis of this standard.This standard applies to grading of green and dried timber. Characteristics apply at the time of grading
19、. This standard does not apply to the strength grading of structural timber or to sawn timber for pallets. This standard is applicable to the following products:a) Oak sawn timber, in the following categories:1)Un-edged boards: individual selected pieces and boules;2)Square edged timber and strips (
20、not exceeding 41 mm thickness);3)Baulks (sum of thickness + width 200 mm and thickness 80 mm). b) Beech sawn timber, in the following categories:1)Un-edged boards: individual selected pieces and boules;2)Square edged timber and strips;3)Prepared timber (dried timber).2Normative referencesThe followi
21、ng referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 844-1:1995, Round and sawn timber Terminology Part 1: Gene
22、ral terms common to round timber and sawn timberEN 844-3:1995, Round and sawn timber Terminology Part 3: General terms relating to sawn timberEN 844-4:1997, Round and sawn timber Terminology Part 4: Terms relating to moisture contentEN 844-6:1997, Round and sawn timber Terminology Part 6: Terms rela
23、ting to dimensions of sawn timberEN 844-7:1997, Round and sawn timber Terminology Part 7: Terms relating to anatomical structure of timberEN 844-9:1997, Round and sawn timber Terminology Part 9: Terms relating to features of sawn timber EN 844-10:1998, Round and sawn timber Terminology Part 10: Term
24、s relating to stain and fungal attack EN 844-11:1998, Round and sawn timber Terminology Part 11: Terms relating to degrade by insectsEN 844-12:2000, Round and sawn timber Terminology Part 12: Additional terms and general indexEN 1310, Round and sawn timber Method of measurement of featuresEN 1311, R
25、ound and sawn timber Method of measurement of biological degradeEN 1313-2, Round and sawn timber Permitted deviations and preferred sizes Part 2: Hardwood sawn timber3Terms and definitionsFor the purposes of this document, the terms and definitions given in EN 844-1:1995, EN 844-3:1995, EN 844-4:199
26、7, EN 844-6:1997, EN 844-7:1997, EN 844-9:1997, EN 844-10:1998, EN 844-11:1998 and EN 844-12:2000 and the following apply.3.1dried timbertimber with a stipulated reduced moisture content3.2green timbertimber that has not been dried to or below the fibre saturation point NOTEGreen timber has a moistu
27、re content normally above 30 %. EN 844-4:19973.3width or length reductionnotional decrease in the actual dimensions of a board to exclude features that may subsequently be removed4Method of determination of sawn timber quality4.1 Rules for gradingHardwood (oak and beech) can be put into grades using
28、 the principles laid down in 4.2, the criteria defined in4.3 and the following tables: Table 2 gives rules for grading oak un-edged boards; Table 3 gives rules for grading oak strips and square edged timber; Table 4 gives rules for grading oak baulks; Table 5 gives rules for grading beech un-edged b
29、oards; Table 6 gives rules for grading beech strips and square edged timber; Table 7 gives rules for grading beech prepared timber.4.2 Grading principles4.2.1Assessment of the qualityFor individual selected boards and boules grading is made on the faces. For other pieces grading is made on faces and
30、 edges. The size, position and frequency of features, sawing defects and deteriorations are taken into account. Non-conformity with the conditions applicable to any one of these elements is sufficient to downgrade the piece.Dimensional variation is not taken into account for quality grading of the p
31、ieces. It is already covered byEN 1313-2 or by any specific requirements defined contractually. Only the following categories can be reduced in width and/or length: Individual selected boards, boules.4.2.2Cases of un-edged boards4.2.2.1Individual selected boardsNo more than 10% of pieces one grade lower than the lowest one stated for the batch is allowed. For mixed grade batches the minimum proportion of each grade shall be identified.4.2.2.2BoulesRecognising the characteristics inherent in a growing tree, a boule