《【英国标准word原稿】BS EN 1320-1997 金属材料焊接的破坏试验.断裂试验.doc》由会员分享，可在线阅读，更多相关《【英国标准word原稿】BS EN 1320-1997 金属材料焊接的破坏试验.断裂试验.doc（23页珍藏版）》请在三一文库上搜索。
1、豆丁网：http:/ STANDARDDestructive tests on welds in metallic materials Fracture testsThe European Standard EN 1320 : 1996 has the status of aBritish Standard| BS EN1320 : 1997|第 15 页 共 23 页豆丁网：http:/ Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI|NO COPYING WITHOUT B
2、SI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 1320 : 1997Committees responsible for thisBritish StandardThe preparation of this British Standard was entrusted to Technical CommitteeWEE/2, upon which the following bodies were represented:Association of Consulting ScientistsBritish Construct
3、ional Steelwork Association Ltd. British Iron and Steel Producers Association Electricity AssociationHealth and Safety Executive Institution of Structural Engineers Lloyds Register of Shipping Ministry of DefencePower Generation Contractors Association (PGCA) (BEAMA Ltd.) Welding InstituteWelding Ma
4、nufacturers Association (BEAMA Ltd.)This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1997Licensed Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontr
5、olled Copy, (c) BSIBSI 1997The following BSI references relate to the work on this standard:Committee reference WEE/2Draft for comment 94/702552 DCISBN 0 580 27082 3Amd. No.DateText affectedAmendments issued since publicationLicensed Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontroll
6、ed Copy, (c) BSIBS EN 1320 : 1997ContentsPage Committees responsible Inside front cover National foreword ii Foreword 2Text of EN 13203BSI 1997iBS EN 1320 : 1997Licensed Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSINational forewordThis British Standard has been
7、prepared by Technical Committee WEE/2 and is the English language version of EN 1320 : 1996 Destructive tests on welds in metallic materials Fracture test, published by the European Committee for Standardization (CEN).EN 1320 : 1996 was produced as a result of international discussions in which theU
8、nited Kingdom took an active part.BS EN 1320 : 1996 supersedes tests detailed in BS 709 : 1983, BS 4206 : 1987 andBS 3451 : 1973 which have been withdrawn by amendment.Cross-referencesPublication referred to Corresponding British StandardEN 970BS EN 970 Welding Visual examination of fusion welded jo
9、intsEN 25817BS EN 25817 : 1992 Arc-welded joints in steel Guidance on quality levels for imperfectionsEN 30042BS EN 30042 : 1994 Arc-welded joints in aluminium and its weldable alloys Guidance on quality levels for imperfectionsCompliance with a British Standard does not of itself confer immunity fr
10、om legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, the ENtitle page, pages 2 to 12 an inside back cover and a back cover.iiBSI 1997EUROPEAN STANDARDEN 1320NORME EUROPE ENNEEUROPA ISCHE NORMOctober 1996ICS 25.160.40Descriptors: Welded jo
11、ints, metals, fusion welding, butt welds, fillet welds, tests, texture, defects, visual examination, test specimen, designationEnglish versionDestructive tests on welds in metallic materials Fracture testEssais destructifs des soudures sur mate riaux me talliques Essai de textureZersto rende Pru fun
12、g von Schweiverbindungen an metallischen Werkstoffen Bruchpru fungThis European Standard was approved by CEN on 1996-09-27. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard wit
13、hout any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language ma
14、de by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
15、 Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 BrusselsLicensed Copy: AUB User, na, Wed Feb 28 10:4
16、0:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI1996 Copyright reserved to CEN membersRef. No. EN 1320 : 1996 EPage 9EN 1320 : 1996ForewordThis European Standard has been prepared byTechnical Committee CEN/TC 121, Welding, the Secretariat of which is held by DS.ContentsForewordPageLicensed Copy: AUB
17、User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSIThis European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 1997, and conflicting national standards shall be withdrawn atthe late
18、st by April 1997.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Po
19、rtugal, Spain, Sweden, Switzerland and the United Kingdom.1 Scope 32 Normative references 33 Definitions 34 Principle 45 Denominations and symbols 46 Dimensions of test pieces 67 Removal of test specimens 98 Test procedure 129 Test result 1510 Test report 15AnnexA (informative) Test report 16License
20、d Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI1 ScopeThis European Standard specifies the sizes of test specimen and the procedures for carrying out fracture tests in order to obtain information about types, sizes and distribution of internal imperfections such
21、as porosity, cracks, lack of fusion, lack of penetration and solid inclusions on the fracture surface.This European Standard applies to metallic materials in all forms of product, with joints made by any fusion welding process with a thickness greater than or equal to 2 mm.This European Standard is
22、used if required by the application standard, or by the agreement between the contracting parties.2 Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text a
23、nd the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.pr
24、EN 970Non-destructive examination of fusion welds Visual examinationEN 25817Arc-welded joints in steel Guidance on quality levels for imperfections (ISO 5817 : 1992)EN 30042Arc-welded joints in aluminium and its weldable alloys Guidance on quality levels for imperfections (ISO 10042 : 1992)3 Definit
25、ionsFor the purposes of this standard, the following definitions apply.3.1 examination length (Lf)Length of the test specimen measured along the weld axis between any side notches (see figure 6).3.2 total examination length (SLf)Sum of the lengths of all the test specimens composing the test piece,
26、measured along the weld axis, of the fracture faces between the side notches of the test specimens (see figure 6).3.3 examination thickness (af)Thickness of the fracture area for each test specimen(see figures 7 and 8).3.4 examination area (Af)Product of the examination length and the examination th
27、ickness for each test specimen.3.5 total examination area ( Af)Sum of all examination areas.4 PrincipleFracture the joint through the weld metal in order to examine the fracture surface. The fracture can be induced by bending or tension, static or dynamic loading. Furthermore, notch dimensions and t
28、emperature can be varied to induce the fracture.Unless otherwise specified, the test shall be carried out at ambient temperature (23 5) C.5 Denominations and symbolsThe denominations and symbols to be used forfracture tests are specified in table 1 and represented in figures 5 to 8.Normally, it is s
29、ufficient to give the basic denomination, but for special application, additional denominations about the notching and test method can be requested.Licensed Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSITable 1 Denominations and symbolsDenominationSymbolUnitButt w
30、eldFillet weldBW FW Test specimen and test piece- Examination length- Examination thickness- Examination area- Area of imperfectionsLf af Af Aimm mm mm2 mm2Side notch- square (q)- round (r)- sharp (s)S Sq Sr Ss Longitudinal notch- Face notch- square (q)- round (r)- sharp (s)- Root notch- square (q)-
31、 round (r)- sharp (s)F Fq Fr Fs R Rq Rr Rs EXAMPLE 1: Test specimen taken from a fillet weld with an examination length of 40 mm and examination thickness of 10 mm. without any requirement about notching and test method:Basic denomination: FW / Lf 3 af; EXAMPLE: FW / 40 3 10. with additional require
32、ment (square face notching and test method):Comprehensive denomination: FW / Lf 3 af / Fq / Figure 8;EXAMPLE: FW / 40 3 10 / Fq / Figure 8. EXAMPLE 2: Test specimen taken from a butt weld with an examination length of 40 mm and examination thickness of 10 mm. without any requirement about notching a
33、nd test method:Basic denomination: BW / Lf 3 af; EXAMPLE: BW / 40 3 10. with additional requirement (round side notching and test method):Comprehensive denomination: BW / Lf 3 af / Sr / Figure 6;EXAMPLE: BW / 40 3 10 / Sr / Figure 6.6 Dimensions of test piecesUnless otherwise specified by the applic
34、ation standard or by agreement between the contracting parties, test piece dimensions shall be in accordance withfigures 1 to 4. The test piece shall provide sufficient test specimens for the required total examination length (SLf) and area (SAf).NOTE. *$ 150 mm for materials of high thermal conduct
35、ivity (e.g. aluminium and copper).t is the thickness of the test piece. All dimensions are in millimetresFigure 1. Test piece for butt welds in plateLicensed Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSINOTE. * $ 150 mm for materials of high thermal conductivity(
36、e.g. aluminium and copper).t is the thickness of the test piece. All dimensions are in millimetresFigure 2. Test piece for butt welds in pipel1l2l1 $ (D + 100)l2 $ (D + 100)NOTE. * $ 150 mm for materials of high thermal conductivity (e.g. aluminium and copper).t1, t2 are the thicknesses of the test
37、piece. All dimensions are in millimetresFigure 3. Test piece for fillet welds on plateNOTE. * $ 150 mm for materials of high thermal conductivity(e.g. aluminium and copper).t1, t2 are the thicknesses of the test piece.l1, l2 are the lengths of the test piece. All dimensions are in millimetresFigure
38、4. Test piece for fillet welds on pipeLicensed Copy: AUB User, na, Wed Feb 28 10:40:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI7 Removal of test specimens7.1 GeneralThe examination length (Lf) and area (Af), and the number of test specimens shall be specified by the application standard or by agre
39、ement between the contracting parties. Welded joints in plates shall be cut transversely to the welded joint into test specimens including approximately equal weld length. The weld axis shall remain in the middle of the test specimen for butt welds.Unless otherwise specified in the application stand
40、ard for welded joints in pipe or by agreement between the contracting parties, the test piece shall provide at least two test specimens.When testing in bending, equal numbers of specimens shall be tested with the root in tension and the face in tension. If the pipe diameter is too small for removing
41、 the required number of test specimens, additional test pieces shall be welded.7.2 MarkingEach test piece shall be marked to identify its exact location in the manufactured product or in the joints from which it has been removed.When removed from the test piece, each test specimen shall be marked.7.
42、3 Extraction7.3.1 GeneralThe extraction method shall avoid the introduction of detrimental thermal or mechanical effects.In general, 25 mm from both ends of the test welds shall be discarded, unless information about the ends of the welds is required (e.g. start/stop imperfections).7.3.2 SteelsThe test specimens shall be cut by thermal cutting or by mechanical means.7.3.3 Other metallic materialsOther metallic materials shall only be cut mechanically.7.4 PreparationFracture of welds in plates or pipes may be assisted by one or more of