《（BS英国标准）BS EN 50131-2-5-2008 Alarm systems – Intrusion and hold-up systems –– Part 2-5 Requirements for combined passive infrared and ultrasonic detectors.doc》由会员分享，可在线阅读，更多相关《（BS英国标准）BS EN 50131-2-5-2008 Alarm systems – Intrusion and hold-up systems –– Part 2-5 Requirements for combined passive infrared and ultrasonic detectors.doc（47页珍藏版）》请在三一文库上搜索。
1、BSI British StandardsNONO COPYINGCOPYING WITHOUTWITHOUT BSIBSI PERMISSIONPERMISSION EXCEPTEXCEPT ASAS PERMITTEDPERMITTED BYBY COPYRIGHTCOPYRIGHT LALAWWraisingraising standardsstandards worldwideworldwideBSI British StandardsBS EN 50131-2-5:2008BSI British StandardsAlarm systems Intrusion and hold-up
2、 systems Part 2-5: Requirements for combined passive infrared and ultrasonic detectorsNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWraising standards worldwideBS EN 50131-2-5:2008BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 50131-2-5:2
3、008. It supersedes DD CLC/TS 50131-2-5:2004 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee GW/1, Electronic security systems, to Subcommittee GW/1/1, Alarm components.A list of organizations represented on this committee can be obtained on request to
4、its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2008ISBN 978 0 580 58456 5ICS 13.320Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was
5、 published under the authority of the StandardsPolicy and Strategy Committee on 31 December 2008.Amendments issued since publicationDate Text affectedBS EN 50131-2-5:2008EUROPEAN STANDARDEN 50131-2-5NORME EUROPENNEEUROPISCHE NORM September 2008 ICS 13.320Supersedes CLC/TS 50131-2-5:2004English versi
6、onAlarm systems - Intrusion and hold-up systems -Part 2-5: Requirements for combined passive infrared and ultrasonic detectorsSystmes dalarme -Systmes dalarme contre lintrusion et les hold-up -Partie 2-5: Exigences pour dtecteurs combins infrarouges passifset ultrasoniquesAlarmanlagen -Einbruch- und
7、 berfallmeldeanlagen - Teil 2-5: Anforderungen an kombinierte Passsiv-Infrarot- und UltraschallmelderThis European Standard was approved by CENELEC on 2008-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Sta
8、ndard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, Fren
9、ch, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, B
10、ulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.CENELECEuropean C
11、ommittee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELE
12、C members.Ref. No. EN 50131-2-5:2008 EForewordThis European Standard was prepared by the Technical Committee CENELEC TC 79, Alarm systems. The text of the draft was submitted to the Unique Acceptance Procedure and was approved byCENELEC as EN 50131-2-5 on 2008-05-01.This European Standard supersedes
13、 CLC/TS 50131-2-5:2004. The following dates were fixed:national standard or by endorsement(dop)2009-05-01latest date by which the national standards conflicting with the EN have to be withdrawn(dow)2011-05-01latest date by which the EN has to be implemented at national level by publication of an ide
14、nticalEN 50131 will consist of the following parts, under the general title Alarm systems Intrusion and hold-up systems:Part 1System requirementsPart 2-2Intrusion detectors Passive infrared detectorsPart 2-3Requirements for microwave detectorsPart 2-4Requirements for combined passive infrared and mi
15、crowave detectors Part 2-5 Requirements for combined passive infrared and ultrasonic detectors Part 2-6 Intrusion detectors Opening contacts (magnetic)Part 2-7-1Intrusion detectors Glass break detectors Acoustic Part 2-7-2Intrusion detectors Glass break detectors Passive Part 2-7-3Intrusion detector
16、s Glass break detectors Active Part 3Control and indicating equipmentPart 4Warning devicesPart 5-3Requirements for interconnections equipment using radio frequency techniquesPart 6Power suppliesPart 7Application guidelinesPart 8Security fog devicesBS EN 50131-2-5:2008EN 50131-2-5:2008 19 ContentsPag
17、eIntroduction. 51Scope . 62Normative references . 63Definitions and abbreviations . 63.1Definitions . 63.2Abbreviations . 74Functional requirements . 74.1Event processing . 74.2Detection . 94.3Operational requirements . 104.4Immunity of the individual technologies to incorrect operation . 104.5Tampe
18、r security . 114.6Electrical requirements . 124.7Environmental classification and conditions . 135Marking, identification and documentation . 135.1Marking and/or identification. 135.2Documentation . 136Testing . 146.1Generalities . 146.2General test conditions . 146.3Basic detection test . 156.4W al
19、k testing . 166.5Switch-on delay, time interval between signals and indication of detection . 196.6Self tests . 196.7Immunity of individual technologies to incorrect operation . 206.8Tamper security . 216.9Electrical tests . 236.10 Environmental classification and conditions . 256.11 Marking, identi
20、fication and documentation . 26Annex A (normative)Dimensions & requirements of the standardised test magnets . 27Annex B (normative)General testing matrix . 30Annex C (informative) W alk test diagrams . 31Annex D (normative)Procedure for calculation of average temperature difference . 34Annex E (inf
21、ormative) Basic detection target for the basic test of detection capability . 35Annex F (informative) Equipment for walk test velocity control . 36Annex G (informative) Immunity to visible and near infrared radiation Notes oncalibration of the light source . 37Annex H (informative) Example list of s
22、mall tools . 38Annex I (informative)Test for resistance to re-orientation of adjustable mountings . 39Bibliography. 40FiguresFigure A.1 Test magnet - Magnet Type 1 . 28Figure A.2 Test magnet - Magnet Type 2 . 29Figure C.1 Detection across the boundary . 31Figure C.2 Detection within the boundary. 31
23、Figure C.3 High velocity and intermittent movement. 32Figure C.4 Close-in detection . 32Figure C.5 Significant range reduction . 33Figure I.1 Re-orientation test . 39TablesTable 1 Events to be processed by grade . 8Table 2 Generation of signals or messages . 8Table 3 General walk test velocity and a
24、ttitude requirements . 9Table 4 Tamper security requirements . 12Table 5 Grade dependencies for electrical requirements . 12Table 6 Range of materials for masking tests . 23Table 7 Operational tests . 25Table 8 Endurance tests . 26Table D.1 Measurement and calculation of the real average temperature
25、 differencebetween the SW T and the background . 34IntroductionThis European Standard is for combined passive infrared and ultrasonic detectors (to be referred to as the detector) used as part of intrusion alarm systems installed in buildings. It includes four security grades and four environmental
26、classes.The purpose of a detector is to detect the broad spectrum infrared radiation emitted by an intruder and, at the same time, to emit ultrasonic radiation over the area being protected, and analyse signals that are returned, to provide the necessary range of signals or messages to be used by th
27、e rest of the intrusion alarm system.The number and scope of these signals or messages will be more comprehensive for systems that are specified at the higher grades.This European Standard is only concerned with the requirements and tests for the detector. Other types of detector are covered by othe
28、r documents identified as EN 50131-2 series.1 ScopeThis European Standard is for combined passive infrared and ultrasonic detectors installed in buildings and provides for security grades 1 to 4 (see EN 50131-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I
29、 to IV (see EN 50130-5). This standard does not include requirements for combined passive infra red and ultrasonic detectors intended for use outdoors.A detector shall fulfil all the requirements of the specified grade.Functions additional to the mandatory functions specified in this standard may be
30、 included in the detector, providing they do not influence the correct operation of the mandatory functions.The European Standard does not apply to system interconnections.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated refer
31、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 50130-4Alarm systems Part 4: Electromagnetic compatibility Product family standard: Immunity requirements for components of fire, intruder and social ala
32、rm systemsEN 50130-5Alarm systems Part 5: Environmental test methodsEN 50131-1Alarm systems Intrusion and hold-up systems Part 1: System requirementsEN 50131-6Alarm systems Intrusion and hold-up systems Part 6: Power suppliesEN 60068 seriesEnvironmental testing (IEC 60068 series)EN 60068-1Environmental testing Part 1: Gen