AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf

上传人:韩长文 文档编号:3641847 上传时间:2019-09-19 格式:PDF 页数:14 大小:77.70KB
返回 下载 相关 举报
AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf_第1页
第1页 / 共14页
AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf_第2页
第2页 / 共14页
AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf_第3页
第3页 / 共14页
AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf_第4页
第4页 / 共14页
AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf_第5页
第5页 / 共14页
亲,该文档总共14页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf》由会员分享,可在线阅读,更多相关《AS 4057-1992 Powered walk-behind and handheld lawn trimmers and lawn edge trimmers-Mechanical safety requirements and test methods1.pdf(14页珍藏版)》请在三一文库上搜索。

1、AS 40571992 ISO 10518:1991 Australian Standard Powered walk-behind and hand- held lawn trimmers and lawn edge trimmersMechanical safety requirements and test methods Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 03 Aug 2007 This Australian Standard was prepared by Committee CS/33, Power Lawnmowers an

2、d Edge Trimmers. It was approved on behalf of the Council of Standards Australia on 21 July 1992 and published on 16 November 1992. The following interests are represented on Committee CS/33: Australian Federation of Consumer Organizations Business and Consumer Affairs, N.S.W. Confederation of Austr

3、alian Industry Department of Public and Consumer Affairs, S.A. Federal Bureau of Consumer Affairs Local Government Association of New South Wales Metal Trades Industry Association of Australia Mower Specialists Association of Australia National Safety Council of Australia (Federal Secretariat) Outdo

4、or Power Equipment Association The WorkCover Authority, N.S.W. Review of Australian Standards. To keep abreast of progress in industry, Australian Standards are subject to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important therefore that

5、Standards users ensure that they are in possession of the latest edition, and any amendments thereto. Full details of all Australian Standards and related publications will be found in the Standards Australia Catalogue of Publications; this information is supplemented each month by the magazine The

6、Australian Standard, which subscribing members receive, and which gives details of new publications, new editions and amendments, and of withdrawn Standards. Suggestions for improvements to Australian Standards, addressed to the head office of Standards Australia, are welcomed. Notificationof any in

7、accuracy or ambiguity found in an Australian Standard should be made without delay in order that the matter may be investigated and appropriate action taken. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 03 Aug 2007 AS 40571992 Australian Standard Powered walk-behind and hand- held lawn trimmers and

8、lawn edge trimmersMechanical safety requirements and test methods First published as AS 40571992. PUBLISHED BY STANDARDS AUSTRALIA (STANDARDS ASSOCIATION OF AUSTRALIA) 1 THE CRESCENT, HOMEBUSH, NSW 2140 ISBN 0 7262 7729 0 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 03 Aug 2007 2 PREFACE This Standa

9、rd was prepared by the Standards Australia Committee on Power Lawnmowers and Edge Trimmers. It is identicalwith andhas been reproduced from ISO 10518:1991,Poweredwalk- behind and hand-held lawn trimmers and lawn edge trimmersMechanical safety requirements and test methods. Of the organizations repre

10、sented on the Committee, the Australian Federation of Consumer Organizations did not agree to the publication of this Standard. The Australian Federation of Consumer Organizations had concerns about the battery stowage requirements, the marking of controls and the determinationof the permissible kin

11、etic energy of the cutting element. Under arrangements made between Standards Australia and the InternationalStandards bodies, ISO and IEC, as well as certain other Standardsorganizations, users of this Australian Standard are advised of the following: (a) Copyright is vested in Standards Australia.

12、 (b) The numberof this Standard is not reproduced on each page;its identityis shown only on the cover and title pages. (c)There may be occasionaldual languagesections, but English is always one of the languages reproduced. (d) Where any cross-references to page numbers appear within the test, these

13、relate to page numbering in the InternationalStandard and are to be disregarded. For the purpose of this Australian Standard, the ISO text should be modified as follows: (i)Substitute a full point for a comma as a decimal point. (ii) Replace the reference to another publication with reference to an

14、Australian Standard as follows: Reference to International StandardAustralian Standard IEC 335Safetyofhouseholdandsimilar electrical appliances AS 335.1Part 1: General requirements3100Approvalandtestspecification General requirementsforelectrical equipment 3156Approval andtest specifications Electri

15、c lawnmowers 3300Approvalandtestspecification General requirements for household and similar electrical appliances ISO 5395Powerlawnmowers,lawntractors, lawn and garden tractors, professional mowers, and lawn and garden tractors, withmovingattachmentsDefinitions, safety requirements and list procedu

16、res 2657Powered rotary lawnmowers CopyrightSTANDARDS AUSTRALIA Users of Standards are reminded that copyright subsists in all Standards Australia publications and software. Except where the Copyright Act allows and except where provided for below no publications or software produced by Standards Aus

17、tralia may be reproduced, stored in a retrieval system in any form or transmitted by any means without prior permission in writing from Standards Australia. Permission may be conditional on an appropriate royalty payment. Requests for permission and information on commercial software royalties shoul

18、d be directed to the head office of Standards Australia. Standards Australia will permit up to 10 percent of the technical content pages of a Standard to be copied for use exclusively in-house by purchasers of the Standard without payment of a royalty or advice to Standards Australia. Standards Aust

19、ralia will also permit the inclusion of its copyright material in computer software programs for no royalty payment provided such programs are used exclusively in-house by the creators of the programs. Care should be taken to ensure that material used is from the current edition of the Standard and

20、that it is updated whenever the Standard is amended or revised. The number and date of the Standard should therefore be clearly identified. The use of material in print form or in computer software programs to be used commercially, with or without payment, or in commercial contracts is subject to th

21、e payment of a royalty. This policy may be varied by Standards Australia at any time. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 03 Aug 2007 3 CONTENTS Page 1Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2Normative references . .

22、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 3Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 4General construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23、 . . . .4 5Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 6Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 7Cutting means . . . . . . . . . . . . . . . . . . . . . . .

24、 . . . . . . . . . . . . . . . . . . . . . . . . .7 8Guarding of cutting means. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 9Mechanical strength and rigidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 ANNEX ASafety instructions for walk-beh

25、ind and hand-held lawn trimmers and lawn edge trimmers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 03 Aug 2007 AUSTRALIAN STANDARD4 Powered walk-behind and hand-held lawn trimmers and lawn edge trimmersMecha

26、nical safety requirements and test methods 1Scope ThisInternationalStandardspecifiesmechanical safety requirements and test methods applicable to powered walk-behind and hand-held lawn trimmers and lawn edge trimmers, with cutting element(s) of non-metallicfilamentlineorfreelypivotingnon- metallic c

27、utter(s) with a kinetic energy of not more than 10 J each, used by a standing operator primarily for cutting grass. It does not apply to scissor-type or rigid-bladed lawn trimmers or lawn edge trimmers. The electrical aspects of electricallypowered lawn trimmers and lawn edge trimmers having a volta

28、ge exceeding42 V d.c. or mains-connectedare not covered by this International Standard. 2Normative references The followingstandardscontainprovisionswhich, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the editions indicated were

29、valid. All stan- dardsaresubjecttorevision,andpartiesto agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Stan

30、dards. ISO 5395:1990,Power lawn-mowers, lawn tractors, lawn and garden tractors, professional mowers, and lawn and garden tractors with mowing attachments Definitions, safety requirements and test procedures. IEC 335-1:1976,Safetyof householdand similar electrical appliances Part 1: General requirem

31、ents. 3Definitions For the purposes of this International Standard, the following definitions apply. 3.1hand-held:Supportedbyhand,possibly assisted by wheel(s), skids or harness, etc. 3.2walk-behind:Normallycontrolledbyan operator walking behind a ground-supported unit. 3.3lawn trimmer: Grass-cuttin

32、gmachinewhere the cutting means operates in a plane approximately parallel to the ground. 3.4lawn edge trimmer: Grass-cutting machine for trimminglawnedgeswherethecuttingmeans operates in a plane approximately perpendicularto the ground. 3.5cutting means: Mechanism used to provide the cutting action

33、 in which one or more cutting elements, cutting by impact, rotate about an axis normal to the cutting plane. 3.6cuttIng element: Single non-metallic filament line or freely pivoting non-metallic cutter. 3.7drive unit: System which supports and powers the cutting means. 4General construction 4.1Handl

34、ing The machine shall be capable of normal use by an operator wearing gloves. Any harness provided shall be of the quick-release type to ensure that the equipment can be quickly detached by the operator in an emergency. COPYRIGHT Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 03 Aug 2007 5 Hand-held l

35、awn trimmers and lawn edge trimmers, or the hand-heldpartsof suchmachines,with a mass of more than 5 kg shall have two handles. The distance between the centre of the two handles shall beatleast250mm, when measuredalongthe length of the handle supportshaft. This measure- ment does not apply to two-h

36、andled lawn trimmers weighing 5 kg or less. The machine mass is deter- mined with all accessories fitted and either with any tanks needed for operation half-full, or with 1 m of supply cable, as appropriate. The gripping width of any handle required by this International Standard shall be at least 1

37、00 mm. 4.2Power-driven components (other than cutting means) Power-driven gears, chains, sprockets, belts, friction drives, pulleys, fans, fan wheels and other moving parts whenever they create a pinch point capable of causing injury, during normal starting and operating of the machine, shall be so

38、positioned or guarded by shieldsorsimilarattachmentsastoprevent accidentalcontactwiththesecomponents. Drive-shafts shall be fully guarded. The principles set out in annex A of ISO 5395:1990 shallbefollowedwhendevelopingaguarding system. The requirements of 4.2 do not apply to any part of a component

39、 functioning in contact with the soil; any axle of a ground wheel. 4.3Heat protection 4.3.1Temperature limits of exposed parts A guard or shield shall be provided to prevent inad- vertentcontactwith any exposedengineexhaust component,greaterthan10cm2and with a hot surface greater than 80C, during no

40、rmal starting and operation of the machine. Handlesandpermanentlyheldcontrolsshallnot exceed 45 C: other controls and surfaces which may be touched during normal operation shall not exceed 55 C. 4.3.2Test method The test shall be conducted in the shade. The engine shall be operatedat its maximum no-

41、loadspeed until thetemperaturesstabilize.All measurements shallbereferredtoanambienttemperatureof 20C 3C. Temperaturesshall be determined by correctingthe observedtemperatureby the differ- ence between the specifiedambient and the test ambient temperature. 4.3.3Test acceptance for exhaust surfaces T

42、he tip or conicalsurfaceof the cone shown in figure 1 shall not make contact with a hot surface of the exhaust system greater than 10 cm2with a tem- perature greater than 80C. Dimensions in millimetres Figure 1 Test cone (see 4.3.3) 4.4Guard attachment All guardsor shieldsrequiredunder 4.2 and 4.3 s

43、hall be either permanently attached, or secured to preventremovalwithout the use of tools, or the constructionof the machine shall be such that it cannot be used without the guard in its guarding position. 4.5Protection from exhaust fumes Engine exhaustsshall be directedaway from the operator. 4.6El

44、ectrical requirements 4.6.1Battery circuits These electrical requirements apply only to battery circuits of less than 42 V. For the electrical require- mentsformains-connectedelectricallydriven machines, reference shall be made to IEC 335-1. 4.6.1.1Electrical cables Electrical cables shall be protec

45、ted, or not located nearanyhotsurfacesorinpotentiallyabrasive contact with metal surfaces. COPYRIGHT Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 03 Aug 2007 6 Thewiringassemblyshall,wherepossible,be groupedtogether,beproperlysupportedandbe located so that no portion is near the exhaust system or in

46、 contact with the carburettor, metallic fuel lines, moving parts or sharp edges. Any edges of metal members likely to be in contact with the cables shall be rounded or protected to prevent possible damage to the cables by cutting or abrasion. 4.6.1.2Battery installation The compartment for a vented

47、storage battery shall have openings to provide ventilation and drainage. Whenthebatteryisintheoperatingposition, electrolyte shall not leak onto parts that would be critically affected to the extent that a hazard would be created from corrosion. 4.6.1.3Overload protection All circuits,exceptstarter-

48、motorandhigh-voltage ignitioncircuits,shallbeprovidedwithoverload protection devices in the ungrounded line near the batteryterminalorstartercable.Theoverload protection may be located in either wire of a two-wire system. Thisrequirementshallnot,however,applyto battery-poweredmachinescapableof passi

49、ngthe following test. Withthemotorshaftlockedtopreventrotation, connect it to its fully charged integral battery and leaveitinthatconditionuntilthebatteryis discharged or failure of any component takes place. The machine shall not emit flames or molten metal. Any internal explosion shall be contained so as not to cause any material to be ejected from the machine. 4.6.1.4Terminalsanduninsulatedelectrical parts Terminals and uninsulated electrical parts and two- wirenon-groundedsystemsshallbeprotected againstshort-circuitingby thefuelcan,or tools, during normal re

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 其他


经营许可证编号:宁ICP备18001539号-1