《BS EN 12502-5-2004 金属材料防腐蚀保护.配水和蓄水系统中腐蚀可能性的评价指南.第5部分铸铁、非合金和低合金钢的影响因素1.pdf》由会员分享，可在线阅读，更多相关《BS EN 12502-5-2004 金属材料防腐蚀保护.配水和蓄水系统中腐蚀可能性的评价指南.第5部分铸铁、非合金和低合金钢的影响因素1.pdf（16页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 12502-5:2004 Protection of metallic materials against corrosion Guidance on the assessment of corrosion likelihood in water distribution and storage systems Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels The European Standard EN 12502-5:2004 has th
2、e status of a British Standard ICS 23.040.99; 77.060; 91.140.60 ? BS EN 12502-5:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 20 January 2005 BSI 20 January 2005 ISBN 0 580 45295 6 National foreword This British Standard is the officia
3、l English language version of EN 12502-5:2004. The UK participation in its preparation was entrusted to Technical Committee ISE/NFE/8, Corrosion of metals and alloys, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. C
4、ross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or
5、of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text;
6、 present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover
7、, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NO
8、RM EN 12502-5 December 2004 ICS 77.060; 23.040.99; 91.140.60 English version Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels
9、 Protection des matriaux mtalliques contre la corrosion - Recommandations pour lvaluation du risque de corrosion dans les installations de distribution et stockage deau - Partie 5 : Facteurs considrer pour la fonte, les aciers non allis et faiblement allis Korrosionsschutz metallischer Werkstoffe -
10、Hinweise zur Abschtzung der Korrosionswahrscheinlichkeit in Wasserverteilungs- und speichersystemen - Teil 5: Einflussfaktoren fr Gusseisen, unlegierte und niedriglegierte Sthle This European Standard was approved by CEN on 22 November 2004. CEN members are bound to comply with the CEN/CENELEC Inter
11、nal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member
12、. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members a
13、re the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United K
14、ingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12502-5:2004: E
15、 EN 12502-5:2004 (E) 2 Contents Page Foreword3 Introduction.4 1 Scope 5 2 Normative references5 3 Terms, definitions, and symbols5 3.1 Terms and definitions .5 3.2 Symbols5 4 Types of corrosion.5 4.1 General5 4.2 Uniform corrosion6 4.3 Pitting corrosion7 4.4 Selective corrosion8 4.5 Bimetallic corro
16、sion 9 4.6 Erosion corrosion10 5 Assessment of corrosion likelihood11 Bibliography12 w w w . b z f x w . c o m EN 12502-5:2004 (E) 3 Foreword This document (EN 12502-5:2004) has been prepared by Technical Committee CEN/TC 262 “Metallic and other inorganic coatings”, the secretariat of which is held
17、by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. This standard is in five parts: Part 1: General
18、 Part 2: Influencing factors for copper and copper alloys Part 3: Influencing factors for hot dip galvanised ferrous materials Part 4: Influencing factors for stainless steels Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels Together these five parts constitute a package o
19、f interrelated European Standards with a common date of withdrawal (dow) of 2005-06. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Es
20、tonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. w w w . b z f x w . c o m EN 12502-5:2004 (E) 4 Introduction This document mainly
21、 results from investigations into and experiences gained of the corrosion of unalloyed and low alloyed ferrous materials (steels and cast irons) in contact with supply waters and raw waters in once- through flow systems. The corrosion likelihood of unalloyed and low alloy ferrous materials (steels a
22、nd cast irons) in contact with water depends on the layers built up from corrosion products that might or might not be protective. When layers are present that are not protective, tuberculation can appear on the walls of the components and can lead to corrosion effects such as: sludge in water, colo
23、uring (red or black water), reduction of free section of pipes or even wall perforation. As a result of the complex interactions between the various influencing factors, the extent of corrosion can only be expressed in terms of likelihood. This document is a guidance document and does not set explic
24、it rules for the use of unalloyed and low alloy ferrous materials in water systems. It can be used to minimize the likelihood of corrosion damages occurring by: assisting in designing, installing and operating systems from an anti-corrosion point of view; evaluating the need for additional corrosion
25、 protection methods for a new or existing system; assisting in failure analysis, when failures occur in order to prevent repeat failures occurring. However, a corrosion expert, or at least a person with technical training and experience in the corrosion field is required to give an accurate assessme
26、nt of corrosion likelihood or failure analysis. w w w . b z f x w . c o m EN 12502-5:2004 (E) 5 1 Scope This document reviews the influencing factors for the corrosion likelihood of bare unalloyed or low alloyed ferrous materials (mild steels and cast irons) used as tubes, tanks and equipment in wat
27、er distribution and storage systems, except for water intended for human consumption. NOTE See EN 12502-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, t
28、he latest edition of the referenced document (including any amendments) applies. EN 12502-1:2004, Protection of metallic materials against corrosion Guidance on the assessment of corrosion likelihood in water distribution and storage systems Part 1: General. EN ISO 8044:1999, Corrosion of metals and
29、 alloys Basic terms and definitions (ISO 8044:1999). 3 Terms, definitions, and symbols 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 8044:1999 and EN 12502- 1:2004 apply. 3.2 Symbols c(O2) concentration of oxygen in mmol/l c(HCO3-) concentrati
30、on of hydrogen carbonate ions in mmol/l c(Ca2+) concentration of calcium ions in mmol/l 4 Types of corrosion 4.1 General The most common types of corrosion are described in EN 12502-1:2004, Clause 4. The types of corrosion considered for steels and cast irons are the following: uniform corrosion; pi
31、tting corrosion; selective corrosion; bimetallic corrosion; erosion corrosion. w w w . b z f x w . c o m EN 12502-5:2004 (E) 6 For each type of corrosion, the following influencing factors (described in EN 12502-1:2004, Table 1 and Clause 5) are considered: characteristics of the metallic material;
32、characteristics of the water; design and construction; pressure testing and commissioning; operating conditions. 4.2 Uniform corrosion 4.2.1 General Uniform corrosion of steel and cast iron is associated with the transfer of iron (II) ions into the water (metal loss). These ions dissolved in the wat
33、er can react with oxygen to form less soluble iron (II)-(III)-hydroxy compounds leading to turbidity and sludge formation. These corrosion effects usually do not lead to corrosion damages. Under flowing conditions with waters containing sufficient amounts of calcium carbonate, protective layers cons
34、isting of calcium carbonate and hydrated iron oxides can be formed if the intensity of localized corrosion is low enough. With similar waters under stagnant conditions, localized corrosion always occurs. 4.2.2 Influence of the characteristics of the metallic material The chemical composition and mic
35、rostructure of these materials as well as the cold deformation have virtually no influence on uniform corrosion. 4.2.3 Influence of the characteristics of the water In oxygen containing waters, corrosion damage because of uniform corrosion only occurs when protective layers cannot form. The precondi
36、tion for the formation of a protective layer is a water composition with: c(O2) 3 mg/l and pH 7,0 and c(HCO3-) 2 mmol/l and c(Ca2+) 1 mmol/l The type and concentration of natural components (e.g. phosphates, aluminosilicates) dissolved in the water can play an important part in the formation of prot
37、ective layers. In the absence of protective layers, the corrosion rate is determined by the concentration of oxidizing agents and/or acidic agents, e.g. carbon dioxide. The uniform corrosion rate is very low if: c(O2) 8,5 w w w . b z f x w . c o m EN 12502-5:2004 (E) 7 4.2.4 Influence of design and
38、construction In water lines designed for water under mainly stagnant conditions, e.g. sprinkler systems, the oxygen concentration rapidly drops under 1 mg/l as a consequence of corrosion. At the same time the pH value increases above 8. The rate of uniform corrosion is insignificant under these cond
39、itions. However, if fresh oxygenated water is brought into the system during testing, then blockage of sprinkler heads with corrosion debris can result. 4.2.5 Influence of pressure testing and commissioning Pressure testing and commissioning have no influence on uniform corrosion. 4.2.6 Influence of
40、 operating conditions Significant variations of operating conditions can modify uniform corrosion. If no protective scale is formed the rate of uniform corrosion increases with increasing flow rate and/or temperature. For the effect of stagnant conditions, see 4.2.4. 4.3 Pitting corrosion 4.3.1 Gene
41、ral Pitting corrosion is the most frequent corrosion effect on steels and cast irons in water distribution and storage systems. It develops from galvanic cells depending on surface conditions of materials, water parameters and service conditions. Anodic areas always form in metallic regions, when th
42、e entry of oxygen is hindered by geometrical factors, e.g. in crevices. The bare metallic areas with non-restricted oxygen access form the cathodic area. The corrosion manifests itself in either shallow or steep-sided pits. Pitting corrosion can be enhanced by microbial activity, which can take plac
43、e in anaerobic conditions, especially under debris. Generally, corrosion rates are high and can rapidly lead to wall perforation of the system. The outer manifestation of corrosion is the formation of tubercles under which anodic areas are to be found, cathodic areas being characterized by relativel
44、y thin surface layers. 4.3.2 Influence of the characteristics of the metallic material Pitting corrosion is influenced by the fact that steels and cast irons are iron-carbon alloys with additional elements, intentionally present or as impurities. For materials with compositions given in EN 545, the
45、influence of alloying elements is usually less important than that of other heterogeneities. The surface quality influences the formation of galvanic cells. Anodic areas are favoured by deposits of all types, e.g. oxide scales, residues of oil and paint, corrosion products. w w w . b z f x w . c o m
46、 EN 12502-5:2004 (E) 8 4.3.3 Influence of the characteristics of the water The likelihood of pitting corrosion decreases with increasing concentration of hydrogen carbonate ions because they are part of a buffering system that is able to neutralize the acidity caused by hydrolysis of the iron ions w
47、ithin the pit. The likelihood of pitting corrosion increases with increasing concentrations of chloride, sulfate and nitrate ions because they replace hydrogen carbonate ions and are not able to buffer the acidity formed within in the pit. Surface waters that contain higher amounts of organic matter
48、 increase the likelihood of microbially enhanced pitting corrosion. 4.3.4 Influence of design and construction Stagnant conditions, which favour the onset of pitting corrosion, predominantly occur in dead legs in iron and steel pipes. Crevices formed by hidden recesses, lap joints, badly executed jo
49、ints and other geometrical factors can induce anodic spots of corrosion elements. The introduction of organic materials, e.g. oil, grease, which can be a source of nutrient for micro-organisms, favour the occurrence of microbial corrosion. In sprinkler systems a very high risk of pitting corrosion exists in the tubes coming from storage vessels with pressurized air, because of the high oxygen content of this water. 4.3.5 Influence of pressure testin