《BS EN 13277-3-2000 Protective equipment for martial arts D Part 3 Additional requirements and test methods for trunk protectors.pdf》由会员分享，可在线阅读，更多相关《BS EN 13277-3-2000 Protective equipment for martial arts D Part 3 Additional requirements and test methods for trunk protectors.pdf（12页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 13277-3:2000 The Eu
2、ropean Standard EN 13277-3:2000 has the status of a British Standard ICS 13.340.10; 97.220.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Protective equipment for martial arts Part 3: Additional requirements and test methods for trunk protectors This British Standard, havi
3、ng been prepared under the direction of the Health and Environment Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 October 2000 BSI 10-2000 ISBN 0 580 36562 X BS EN 13277-3:2000 Amendments issued since publication Amd. No.DateComments Nation
4、al foreword This British Standard is the official English language version of EN 13277-3:2000. The UK participation in its preparation was entrusted by Technical Committee PH/3, Protective clothing, to Subcommittee PH/3/11, Protective equipment for sports players, which has the responsibility to: ai
5、d enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represent
6、ed on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondenc
7、e Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself
8、 confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. EUROPEAN STANDARD NORME EUROPENNE
9、 EUROPISCHE NORM EN 13277-3 August 2000 ICS 13.340.10 English version Protective equipment for martial arts - Part 3: Additional requirements and test methods for trunk protectors Equipement de protection pour les arts martiaux - Partie 3: Exigences et mthodes dessai complmentaires relatives aux pro
10、tge-torses Schutzausrstung fr den Kampfsport - Teil 3: Zustzliche Anforderungen und Prfverfahren fr den Oberkrperschutz This European Standard was approved by CEN on 5 August 2000. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thi
11、s European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (E
12、nglish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech R
13、epublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stas
14、sart, 36 B-1050 Brussels 2000 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13277-3:2000 E Page 2 EN 13277-3:2000 Contents Page Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15、 . .2 1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 2 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 3 Terms and definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16、 . . . . . .3 4 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 5 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 6 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17、 . . . . . . . . . . . . . .7 7 Information supplied by the manufacturer . . . . . . . . . . . . . . . . . . . . . . . .7 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU directives . . . . . . . . . . . . . . . . . . . .8 Foreword
18、This European Standard has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical
19、text or by endorsement, at the latest by February 2001, and conflicting national standards shall be withdrawn at the latest by February 2001. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essenti
20、al requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Sta
21、ndard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. It is one of a series covering requirements and test methods for protective equipment used in mar
22、tial arts. Page 3 EN 13277-3:2000 1 Scope This European Standard specifies additional requirements and test methods for trunk protectors used in unarmed martial arts such as taekwondo, karate, kick-boxing and similar disciplines. It also applies to breast protectors for men. For general requirements
23、 and test methods for protective equipment for matial arts see EN 13277-1. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications ar
24、e listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies (including amendments)
25、. EN 13277-1 : 2000 Protective equipment for martial arts Part 1: General requirements and test methods 3 Terms and definitions For the purposes of this European Standard the terms and definitions given in EN 13277-1 apply. 4 Requirements 4.1 Sizing The manufacturer shall indicate in centimetres the
26、 range of the wearers height and chest girth for which this protector is designed. 4.2 Combinations Trunk protectors can be used in combination with other protectors for martial arts. In the case of combined use, the requirements specified for the individual protectors are also to apply. Possible co
27、mbinations shall be indicated in the information supplied by the manufacturer. If combined use is not permitted by the manufacturer, this restriction shall be indicated in the information supplied by the manufacturer. 4.3 Restraint A restraint system shall be supplied by the manufacturer which enabl
28、es the user to attach trunk protectors with the support of no more than one assistant. 4.4 Zone of protection Location and dimensions of the zone of protection see Figure 1 and Table 1. 标准分享网 The manufacturer shall indicate in centimetres the range of the wearers height and chest girth for which thi
29、s 标准分享网 The manufacturer shall indicate in centimetres the range of the wearers height and chest girth for which this 4.2 Combinations 标准分享网 4.2 Combinations Trunk protectors can be used in combination with other protectors for martial arts. 标准分享网 Trunk protectors can be used in combination with oth
30、er protectors for martial arts. For the purposes of this European Standard the terms and definitions given in EN 13277-1 apply. For the purposes of this European Standard the terms and definitions given in EN 13277-1 apply. The manufacturer shall indicate in centimetres the range of the wearers he
31、ight and chest girth for which this The manufacturer shall indicate in centimetres the range of the wearers height and chest girth for which this Page 4 EN 13277-3:2000 Figure 1 - Location of the zone of protection of trunk protectors Table 1 - Zone of protection of trunk protectors Dimensions in m
32、illimetres Wearers height l1l2l3l4l5 min.min.min.min.min. 1 880810200250210150 4.5 Impact performance Trunk protectors comply with this standard if the worst result after testing in accordance with 5.5 meets the following requirements: Impact energy: 12 J; Peak force: max. 3 kN; Positions to be test
33、ed: min. 3. 5 Testing 5.1 Sampling See EN 13277-1 : 2000, 5.1 标准分享网 标准分享网 660 标准分享网 660 标准分享网 from 1 520 to 1700 标准分享网 from 1 520 to 1700 标准分享网 标准分享网 710 标准分享网 710 标准分享网 标准分享网 标准分享网 from 1 700 to 1 880 标准分享网 from 1 700 to 1 880 标准分享网 标准分享网 标准分享网 标准分享网 1 880 标准分享网 1 880 Dimensions in millimetres Di
34、mensions in millimetres 3 3 l l min. min. 140 140 150 150 Page 5 EN 13277-3:2000 5.2 Conditioning See EN 13277-1 : 2000, 5.2 5.3 Restraint Restraint testing shall be carried out as defined in EN 13277-1 : 2000, 5.4. When testing the restraint the protector shall be attached to the trunk of
35、 a test person of an appropriate height in accordance with the information supplied by the manufacturer. A test force of 50 N shall be applied at the edge of the zone of protection, in the directions and in the order shown on Figure 2, tangential to the surface of the body of the test person. Key 1
36、to 6 Directions and order of the tests Figure 2 - Restraint test of trunk protectors 5.4 Zone of protection When testing according to EN 13277-1 : 2000, 5.5, the protector shall be attached to a test person of an appropriate height in accordance with the information supplied by the manufacturer. The
37、 gauge shall be placed onto the surface of the zone of protection. When the position of best coverage of the gauge is found, the outline of the gauge shall be marked on the protector. 标准分享网 1 to 6 Directions and order of the tests 标准分享网 1 to 6 Directions and order of the tests Page 6 EN 13277-3:200
38、0 5.5 Impact performance 5.5.1 Apparatus The principle of impact testing is shown in Figure 3. A flat horizontal steel plate with a width of at least 300 mm, a length of at least 350 mm and a thickness of at least 20 mm shall be used as a support of the sample. In the centre of the flat plate there
39、shall be a cylindrical hole with a diameter of (106 2) mm. A cylindrical anvil with a diameter of (100 2) mm, a thickness of at least 20 mm with a flat upper surface shall be mounted on a load cell. The surface of the anvil facing the striker shall be in level with the surface of the flat plate with
40、 a tolerance of 1 mm. A compression ring made of steel with a mass of (10 0,1) kg, (140 0,1) mm internal and (260 4) mm external diameter shall be used to fix the sample to the support. The striker shall be able to fall free in the vertical axis of the anvil with a tolerance of 2 mm. The striker sha
41、ll be guided in such a way, that it will always reach at least 95 % of the freefall velocity. A means of measuring the velocity of the striker at the point of impact shall be provided. To measure the maximum peak force an electronic measurement device with the following characteristics shall be used
42、: Measurement frequency: min. 2 000 Hz; Accuracy class of the load cell: 0,2; Maximum load: 10 kN. 5.5.2 Procedure The trunk protector shall be placed on the flat support so that the test positions to be tested shall be above the centre of the anvil and shall be fixed with the compression ring. The
43、compression ring shall be placed so that the anvil is situated in the centre of the ring with a tolerance of 5 mm. The trunk protector shall be moved on the support in order to reach every test position to be tested. If it is not possible to press the trunk protector flat with the compression ring,
44、the protector shall be cut, until it is possible to place it flat. The test positions shall be selected so that they are not closer than 20 mm to the limit of the zone of protection. If the test position is closer to the edge of the zone of protection than 70 mm, and there is a gap between the prote
45、ctor and the compression ring, a part of the same protector or of another protector of the same construction shall be cut and placed in the gap. The test positions shall be selected to include the positions on the protector where the worst test results are assumed to be likely. Three impacts of the
46、same energy level shall be carried out on each test position with an interval of (60 10) s. No other test position previously tested shall be within a circle of 80 mm around the test position to be tested. If positions are selected to be impacted less than 80 mm distant from each other, at least two
47、 protectors of the same type shall be selected for impact testing. 标准分享网 The trunk protector shall be placed on the flat support so that the test positions to be tested shall be above the 标准分享网 The trunk protector shall be placed on the flat support so that the test positions to be tested shall be a
48、bove the centre of the anvil and shall be fixed with the compression ring. 标准分享网 centre of the anvil and shall be fixed with the compression ring. The compression ring shall be placed so that the anvil is situated in the centre of the ring with a tolerance of 标准分享网 The compression ring shall be placed so that the anvil is situated in the centre of the ring with a tolerance of To measure the maximum peak force an electronic measurement device with the followi