《BS EN 1335-2-2009 Office furniture — Office work chair Part 2 Safety requirements.pdf》由会员分享，可在线阅读，更多相关《BS EN 1335-2-2009 Office furniture — Office work chair Part 2 Safety requirements.pdf（12页珍藏版）》请在三一文库上搜索。
1、? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? BS EN 1335-2:2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1335-2 April 2009 ICS 97.140Supersedes EN 1335-2:2000 English Version Office furniture - Office work chair - Part 2: Safety requirements Mobilier de bureau - Siges de tr
2、avail de bureau - Partie 2: Exigences de scurit Brombel - Bro-Arbeitsstuhl - Teil 2: Sicherheitsanforderungen This European Standard was approved by CEN on 28 February 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europ
3、ean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (Englis
4、h, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,
5、Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATIO
6、N COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1335-2:2009: E BS EN 1335-2:2009 EN 1335-2:2009 (E) 2 Contents
7、 Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Safety requirements 4 4.1 General design requirements .4 4.1.1 Corners and edges, trapping, pinching and shearing .4 4.1.2 Adjusting devices 5 4.1.3 Connections .5 4.1.4 Avoidance of soiling 5 4.2 Test sequence 5 4.3 St
8、ability during use6 4.4 Rolling resistance of the unloaded chair 6 4.5 Strength and durability .6 5 Information for use 7 Annex A (normative) Loads, masses and cycles for safety tests 8 ? BS EN 1335-2:2009 EN 1335-2:2009 (E) 3 Foreword This document (EN 1335-2:2009) has been prepared by Technical Co
9、mmittee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the
10、latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1335-2:2000. This series consist o
11、f following parts: EN 1335-1, Office furniture Office work chair Part 1: Dimensions Determination of dimensions; EN 1335-2, Office furniture Office work chair Part 2: Safety requirements; EN 1335-3, Office furniture Office work chair Part 3: Test methods. The main changes with respect to the previou
12、s edition are listed below: a) castor durability (former 6.2) has been defined as functional test; b) foot rest stability and foot rest static load have been defined as safety test. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are
13、 bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swede
14、n, Switzerland and the United Kingdom. ? BS EN 1335-2:2009 EN 1335-2:2009 (E) 4 1 Scope This part of EN 1335 specifies the mechanical safety requirements for office work chairs. The requirements are based upon use for 8 h a day by persons weighing up to 110 kg. For more severe conditions of use, inc
15、reased requirements will be necessary. Annex A (normative) includes loads, masses and cycles for safety tests. Additional loads, masses and cycles for functional tests can be found in EN 1335-3:2009, Annex C. 2 Normative references The following referenced documents are indispensable for the applica
16、tion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1335-1:2000, Office furniture Office work chair Part 1: Dimensions Determination of dimensions EN 1335-3:2009, Off
17、ice furniture Office work chair Part 3: Test methods EN 12529:1998, Castors and wheels Castors for furniture Castors for swivel chairs Requirements 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 castor assembly comprising a housing, one or m
18、ore wheels, an axle and, if required, accessories EN 12529:1998 4 Safety requirements 4.1 General design requirements 4.1.1 Corners and edges, trapping, pinching and shearing The chair shall be so designed as to minimise the risk of injury to the user. All parts of the chair with which the user come
19、s into contact during intended use, shall be so designed that physical injury and damage to property are avoided. These requirements are met when: a) the safety distance of accessible movable parts is either 8 mm or 25 mm in any position during movement; b) accessible corners are rounded with minimu
20、m 2 mm radius; ? BS EN 1335-2:2009 EN 1335-2:2009 (E) 5 c) the edges of the seat, back rest and arm rests which are in contact with the user when sitting in the chair are rounded with minimum 2 mm radius; d) the edges of handles are rounded with minimum 2 mm radius in the direction of the force appl
21、ied; e) all other edges are free from burrs and rounded or chamfered; f) the ends of accessible hollow components are closed or capped. 4.1.2 Adjusting devices Movable and adjustable parts shall be designed so that injuries and inadvertent operation are avoided. It shall be possible to operate the a
22、djusting devices from sitting position in the chair. 4.1.3 Connections It shall not be possible for any load bearing part of the chair to come loose unintentionally. 4.1.4 Avoidance of soiling All parts which are lubricated to assist sliding (greasing, lubricating, etc.) shall be designed to protect
23、 users from lubricant stains when in normal use. 4.2 Test sequence The same chair shall be tested in the following sequence: a) stability tests (optional); b) rolling resistance test (optional); c) seat and back rest tests; d) foot rest static load test; e) arm rests durability test; f) arm rest dow
24、nward static load test - central (see Table A.2, Footnote a); g) stability tests; h) arm rest downward static load test - central (see Table A.2, Footnote b); i) rolling resistance test. ? BS EN 1335-2:2009 EN 1335-2:2009 (E) 6 4.3 Stability during use The chair shall not overbalance under the follo
25、wing conditions: a) by pressing down on the front edge of the seat surface in the most adverse position; b) by leaning out over the arm rests; c) by leaning against the back rest; d) by sitting on the front edge. Requirement a) is fulfilled if the chair does not overbalance when tested according to
26、7.1.1 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard. Requirements b) and d) are fulfilled if the chair does not overbalance when tested according to 7.1.2, 7.1.3, 7.1.4 and 7.1.5 of EN 1335-3:2009 with the forces and numbers of cycles according to Ta
27、ble A.1 of this standard. Requirement c) is fulfilled if the chair does not overbalance when tested according to 7.1.6 or 7.1.7 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard. 4.4 Rolling resistance of the unloaded chair The unloaded chair shall not r
28、oll unintentionally. This requirement is met when: a) the castors are of identical construction; b) the rolling resistance is ? 12 N when tested according to EN 1335-3:2009, 7.4. 4.5 Strength and durability The chair shall be constructed to ensure that it does not create a risk of injury to the user
29、 of the chair under the following conditions: a) sitting on the seat, both centrally and off-centre; b) moving forward, backwards, and sideways while sitting in the chair; c) leaning over the arm rests; d) pressing down on the arm rests while getting up from the chair. These requirements are fulfill
30、ed when after the tests specified in 7.2.1, 7.2.2, 7.2.6, 7.3.1 and 7.3.2 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard: e) there are no fractures of any member, joint or component, and f) there is no loosening of joints intended to be rigid, and g)
31、no major structural element is significantly deformed and the chair fulfils its functions after removal of the test loads and when: ? BS EN 1335-2:2009 EN 1335-2:2009 (E) 7 h) after the test in 7.2.3 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard, the
32、 arm rests show no fracture. 5 Information for use Each chair shall be accompanied by information for use in the language of the country in which it will be delivered to the end user. It shall contain at least the following details: a) information regarding the intended use; b) information regarding
33、 possible adjustments and chair type (see EN 1335-1:2000); c) instruction for operating the adjusting mechanisms; d) instruction for the care and maintenance of the chair; e) information regarding all adjustments; f) information for chairs with seat height adjustments with energy accumulators that o
34、nly trained personnel may replace or repair seat height adjustment components with energy accumulators; g) information on the choice of castors in relation to the floor surface. ? BS EN 1335-2:2009 EN 1335-2:2009 (E) 8 Annex A (normative) Loads, masses and cycles for safety tests Table A.1 Loads, ma
35、sses and cycles for stability tests Clauses given in EN 1335-3:2009 Test Loads Cycle 7.1.1 Front edge overturning M1 27 kg 1 7.1.2 Forward overturning F1 F2 600 N 20 N 1 7.1.3 Forward overturning for chairs with foot rests F1 F2 1 100 N 20 N 1 7.1.4 Sideways overturning for chairs without arm rests
36、F1 F2 600 N 20 N 1 7.1.5 Sideways overturning for chairs with arm rests F1 F2 F3 250 N 350 N 20 N 1 7.1.6 Rearwards overturning of chairs without back rest inclination F1 F2 600 N 192 N 1 7.1.7 Rearwards overturning of chairs with back rest inclination Number of discs: 13 1 BS EN 1335-2:2009 EN 1335
37、-2:2009 (E) 9 Table A.2 Loads and cycles for strength and durability tests Clauses given in EN 1335-3:2009 Test Loads Cycles 7.2.1 Seat front edge static load test F11 600 N 10 7.2.2 Combined seat and back static load test F1 F2 1 600 N 560 N 10 7.2.6 Foot rest static load test F 1 300 N 10 7.3.1 Se
38、at and back durability Step 1 Loading Point A F 1 500 N 120 000 Step 2 Loading Point C F 1 200 N 80 000 Loading Point B F 320 N Step 3 Loading Point J F 1 200 N 20 000 Loading Point E F 320 N Step 4 Loading Point F F 1 200 N 20 000 Loading Point H F 320 N Step 5 Loading Point D and G (alternating) F
39、 1 100 N 20 000 7.3.2 Arm rest durability F 400 N 60 000 7.2.3 Arm rest downward static load test central F 750 N a5 F 900 N b5 a This test shall be carried out before the stability tests b This test shall be carried out after the stability tests ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?