《BS EN 10230-1-2000 Steel wire nails — Loose. nails for general applications..pdf》由会员分享，可在线阅读，更多相关《BS EN 10230-1-2000 Steel wire nails — Loose. nails for general applications..pdf（28页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 10230-1:2000 The Eu
2、ropean Standard EN 10230-1:1999 has the status of a British Standard ICS 21.060.50; 77.140.65 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Steel wire nails Part 1: Loose nails for general applications This British Standard, having been prepared under the direction of the En
3、gineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 BSI 01-2000 ISBN 0 580 35464 4 BS EN 10230-1:2000 Amendments issued since publication Amd. No.DateComments National foreword This British Standard is the English language
4、 version of EN 10230-1:1999. The UK participation in its preparation was entrusted to Technical Committee ISE/26, Steel wire, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for cha
5、nge, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or E
6、uropean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the neces
7、sary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pag
8、es 2 to 25 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. ? ? ? ? ? ? ? !“#$%?$#? ?#$?1?!=?-“?# b)?type of nail; c)?nominal characteristic dimension; d)?length; e)?type and surface of head; f)?type of shank; g)?type of point; h)?sur
9、face coatings. Unless otherwise specified, nails with flat smooth circular heads, plain shanks and diamond points shall be supplied. Page 11 EN 10230-1:1999 ?BSI 01-2000 6? Requirements 6.1? Materials and manufacture Nails shall be produced from wire drawn from rods produced in accordance with EN 10
10、016 Parts 1 to 4. Nails produced in accordance with this European Standard shall not be subjected to heat treatment after fabrication except for that incurred during surface coating. Where heat treatment is applied after fabrication the purchaser shall be informed. 6.2? Surface coating The surface o
11、f the wire nails shall comply with one of the following: a)?Uncoated. The surface of the nails shall be free from rust; b)?Zinc coated or zinc alloy coated, with a minimum zinc purity of 98,5 % in the outer surface of the coating, by one of the following alternatives: 1)?Hot dipped to provide a mini
12、mum coating of 300 g/m 2at an Acceptable Quality Level (AQL) of 10 %; 2)?Barrel coated to provide a minimum coating of 300 g/m 2 at an AQL of 10 % of nails with nominal characteristic dimensions greater than 2.6 mm; 3)?Electroplated zinc coatings in accordance with ISO 2081; 4)?Other zinc or zinc al
13、loy coating methods such as sheradizing or mechanical zinc plating as agreed between purchaser and supplier. c)?Lacquered, cement coated or phosphate coated. 6.3?Form and dimensions The form and preferred dimensions are given in tables 1 to 12. NOTE Other lengths having incremental steps usually of
14、5 mm are possible subject to agreement between purchaser and supplier. 6.3.1?Nail point The following types of nail points shall be used: ? diamond point; ? diamond point offset; ? round point; ? chisel point; ? cut point. 6.3.2?Nail shank The following forms of nail shank shall be used: ? plain sha
15、nk; ? indented shank; Page 12 EN 10230-1:1999 ?BSI 01-2000 ? spiral rolled shank; ? ring rolled shank; ? twisted shank; ? grooved shank. The cross-section of nail Tables 1 to 12. Nominal nail characteristic dimensions for indented, spiral rolled and ring rolled shanks are as for plain shank. 6.3.3?
16、Nail head The top surface of the nail head shall be smooth or chequered. NOTE The top surface of the head may be marked by using raised or sunken letters, signs or numbers. The following types of head shall be used: ? circular flat head; ? countersunk head; ? lost round head; ? lost oval head; ? bra
17、d oval head; ? flat countersunk; ? cup head; ? spring head; ? washer head; ? clout head 7? Tolerances 7.1?Length,l The tolerance on the nail length shall be 0,5 ?d. 7.2? Nominal characteristic dimension, d The tolerance on the nominal characteristic dimension applies to the nail shank before coating
18、. The nominal characteristic dimension tolerances on nails shall be T1 of EN 10218-2. 7.3? Head diameter, dh The tolerance on the head diameter of nails shall be 0,05 ?dhwith a minimum of 0,2 mm. Page 13 EN 10230-1:1999 ?BSI 01-2000 8? Sampling and testing The manufacturer, is responsible for the co
19、ntrol of product quality by the application of statistical methods of sampling and analysis of results with AQL values as agreed between purchaser and supplier. When required by the purchaser the coating weight of nails shall be tested in accordance with the gravimetric method in prEN 10244-1 and pr
20、EN 10244-2. The total area shall be taken as (total shank area + 2 (head area). 9? Inspection and documentation Unless otherwise agreed at the time of the order, non specific testing and inspection documentation shall be provided according to the requirements of EN 10021 and EN 10204. 10?Packaging a
21、nd labelling Nails are usually supplied packaged in cartons by net weight or by an approximate number of nails. The label or text on the package shall give the following: ? number of this European Standard i.e. EN 10230-1; ? type; ? length and nominal characteristic dimension; ? surface coating; ? w
22、eight or approximate number of nails; ? manufacturer. Page 14 EN 10230-1:1999 ?BSI 01-2000 Table 1 Dimensions for circular, flat, flat countersunk and cup head, plain shank nails Dimensions in mm Nominal 1,01,21,41,61,82,02,22,42,73,03,43,84,24,65,05,56,07,08,0 characteristic dimension D Nail10 Leng
23、th15 L20 2525 3030303030 4040 45404040 50505050 606060 707070 808080 90909090 100100100100 110 120120 140140 150 160 180 200 280 Head2.83.33.94.04.55 ,05.55.96.16.87.77.68.49.21011121416 diameter dh Page 15 EN 10230-1:1999 ?BSI 01-2000 Table 2 Dimensions for circular, flat and flat countersunk head,
24、 grooved shank nails Dimensions in mm Nominal1,41,61,82,02,22,42,73,03,43,84,24,65,05,56,07,08,0 characteristic dimension D Nail20 Length25 L303030 3535 404040 505050 6060606060 70707070 80808080 9090909090 100100100100100 110110 120120120120 130 140140140 150150 160 170 180 200200 220 250 280 300 H
25、ead3,23,64,04,55,05,55,96,87,77,78,49,21011121416 diameter dh Page 16 EN 10230-1:1999 ?BSI 01-2000 Table 3 Dimensions for circular, flat and flat countersunk head, square shank nails Dimensions in mm Nominal 1,01,21,41,61,71,82,02,22,52,83,13,43,84,24,64,85,56,07,0 characteristic dimension d Nail152
26、025253035404555658090100125130150160180210 length353535405050607595125175190260 l40556590100200 Head2,53,03,54,04,34,55,05,56,37,07,88,59,510,511,512,013,815,017,5 diameter dh Page 17 EN 10230-1:1999 ?BSI 01-2000 Table 4 Dimensions for lost round head, plain shank nails Dimensions in mm Nominal1,01,
27、21,41,61,82,02,22,42,73,03,43,84,24,65,0 characteristic dimension d Nail length10 l1520 2525 3030303030 4040 45404040 50505050 606060 707070 808080 90909090 100100100100 110 120120 140 Head 1,41,72,02,22,52,83,13,43,84,24,85,35,96,47,0 diameter dh Page 18 EN 10230-1:1999 ?BSI 01-2000 Table 5 Dimensi
28、ons for lost round head, grooved shank nails Dimensions in mm Nominal1,41,61,82,02,22,42,73,03,43,84,24,65,0 characteristic dimension d Nail length20 l25 303030 3535 404040 505050 6060606060 70707070 80808080 9090909090 100100100100100 110110 120120120120 130 140140 150 Head2,02,22,52,83,13,43,84,24
29、,85,35,96,4 7,0 diameter dh Page 19 EN 10230-1:1999 ?BSI 01-2000 Table 6 Dimensions for lost round head, plain shank nails Dimensions in mm Nominal hti ti 1,01,21,41,61,71,82,02,22,52,83,13,43.84,2 dimension d Nail length152025253035404555658090100125 l353535405050607595125 40556590100 Head2,53,03,5
30、4,04,34,55,05,56,37,07,88,59,510,5 diameter dh Page 20 EN 10230-1:1999 ?BSI 01-2000 Table 7 Dimensions for clout head, plain shank nails Dimensions in mm Nominal characteristic dimension2,22,42,73,03,43,84,6 d Nail length20 2520 l302525 303030 4035 40404040 4545 5050505050 6565 75 100 Head diameter7
31、,37,98,99,911,211,813,1 dh Page 21 EN 10230-1:1999 ?BSI 01-2000 Table 8 Dimensions for extra large clout head nails Dimensions in mm Nominal characteristic dimension2,02,22,42,73,0 d Nail length15 l2020202020 25252525 303030 3535 4040 5050 60 Head diameter? 7,5 ? 7,7 ? 8,4? 9,4? 11 dh Page 22 EN 102
32、30-1:1999 ?BSI 01-2000 Table 9 Dimensions for countersunk panel pin head, plain shank nails 1. 32 included angle Dimensions in mm Nominal characteristic dimension1,01,41,61,8 d Nail length15 l202020 2525 303030 4040 Head1,42,02,22,5 diameter dh Page 23 EN 10230-1:1999 ?BSI 01-2000 Table 10 Dimension
33、s for springhead, square twisted shank nails 1)d Measured over the diagonals Dimensions in mm Nominal characteristic dimension d3,43,8 Nail length l5050 6060 7070 7575 8080 90 100100 Head diameter dh? 18 ? 18 NOTE. The nail length is measured under the head. Page 24 EN 10230-1:1999 ?BSI 01-2000 Tabl
34、e 11 Dimensions for washer head plain shank nails Dimensions in mm Nominal characteristic dimension d3,03,4 Nail length l40 50 6070 80 90 100 Head diameter dh? 18? 18 NOTE. The heads are usually manufactured by using plain washers but other shapes are permitted. Page 25 EN 10230-1:1999 ?BSI 01-2000
35、Table 12 Dimensions for lost oval head and brad oval head oval plain shank nails Lost oval head Brad oval head Dimensions in mm Nominald1,21,62,02,42,73,43,84,24,65,0 characteristic dimensions D2,02,73,43,84,25,05,56,06,57,0 Nail length20 l25 30 40 45 50 60 65 75 90 100 125 150 Head diameter dh 1,6d
36、1,92,63,23,84,35,46,16,77,48,0 Dh 1,4D2,83,84,85,35,87,07,78,49,19,8 BS EN 10230-1:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
37、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by
38、Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding
39、an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which en
40、sures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it
41、 is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Export
42、ers Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial
43、discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international sta
44、ndardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not p
45、reclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.