《BS EN 10088-5-2009 Stainless Steels - Part 5 Technical Delivery Conditions.pdf》由会员分享，可在线阅读，更多相关《BS EN 10088-5-2009 Stainless Steels - Part 5 Technical Delivery Conditions.pdf（56页珍藏版）》请在三一文库上搜索。
1、? ? ICS 77.140.20; 77.140.60; 77.140.65; 77.140.70 ? ? ? ? ?!?“?#? ?#? $#?%? 77.140.50; 77.140.65 English Version Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes Aciers inoxydables - P
2、artie 5 : Conditions techniques des livraisons pour les barres, fils trfils, profils et produits transforms froid en acier rsistant la corrosion pour usage de construction Nichtrostende Sthle - Teil 5: Technische Lieferbedingungen fr Stbe, Walzdraht, gezogenen Draht, Profile und Blankstahlerzeugniss
3、e aus korrosionsbestndigen Sthlen fr das Bauwesen This European Standard was approved by CEN on 21 February 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any a
4、lteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by
5、translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, G
6、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORM
7、UNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10088-5:2009: E BS EN 10088-5:2009 EN 10088-5:2009 (E) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Ter
8、ms and definitions .6 4 Designation and ordering .6 4.1 Designation of steel grades 6 4.2 Order designation 6 5 Classification of grades 7 6 Requirements .8 6.1 Steelmaking process .8 6.2 Delivery condition 8 6.3 Chemical composition 8 6.4 Chemical corrosion properties .8 6.5 Mechanical properties .
9、8 6.6 Surface quality .9 6.7 Internal soundness 9 6.8 Formability at room temperature .9 6.9 Dimensions and tolerances on dimensions and shape 9 6.10 Calculation of mass and tolerances on mass 10 7 Inspection and testing 10 7.1 General . 10 7.2 Agreement on tests and inspection documents . 10 7.3 Sp
10、ecific inspection and testing . 11 7.4 Test methods . 11 7.5 Retests . 12 8 Evaluation of conformity 12 8.1 General . 12 8.2 Initial type testing . 12 8.3 Factory production control (FPC) . 13 9 Marking 15 10 Dangerous substances 15 Annex A (informative) Guidelines for further treatment (including h
11、eat treatment) in fabrication 42 Annex B (normative) Applicable dimensional standards . 46 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/106/EEC, EU Construction Products Directive . 47 Bibliography . 53 BS EN 10088-5:2009 EN 100
12、88-5:2009 (E) 3 Foreword This document (EN 10088-5:2009) has been prepared by Technical Committee ECISS/TC 23 “Steels for heat treatment, alloy steels and free-cutting steels - Qualities and dimensions”, the secretariat of which is held by DIN. This European Standard shall be given the status of a n
13、ational standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject o
14、f patent rights other than those identified above. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 10088, under the general title “Stainless steels“, consists of the following parts: Part 1: List of stainless steels (including a table of European St
15、andards, in which these stainless steels are further specified, see Annex D); Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes; Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright pr
16、oducts of corrosion resisting steels for general purposes; Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes; Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels f
17、or construction purposes. The European Organisation for Standardisation (CEN) draws attention to the fact that it is claimed that compliance with this document may involve the use of patents concerning two steel grades. CEN takes no position concerning the evidence, validity and scope of these paten
18、t rights. The holder of these patent rights has assured CEN that they are willing to negotiate licenses, under reasonable and non-discriminatory terms and conditions, with applicants throughout the world. In this respect, the statements of the holders of these patent rights are registered with CEN.
19、Information may be obtained from: Sandvik AB SE-811 81 SANDVIKEN Sweden for grade 1.4477 Outokumpu Stainless AB SE-77480 AVESTA Sweden for grade 1.4162 This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essent
20、ial requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annex ZA, which is an integral part of this document. BS EN 10088-5:2009 EN 10088-5:2009 (E) 4 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countrie
21、s are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
22、Sweden, Switzerland and the United Kingdom. BS EN 10088-5:2009 EN 10088-5:2009 (E) 5 1 Scope 1.1 The scope of this part of EN 10088 is to specify the technical delivery conditions for hot or cold formed bars, rods, wire, sections and bright products of standard and special grades of corrosion resist
23、ing stainless steels for construction purposes in addition to the general technical delivery conditions specified in EN 10021. 1.2 This European Standard does not apply to components manufactured by further processing of the product forms listed in 1.1 with quality characteristics altered as a resul
24、t of such further processing. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli
25、es. EN 10002-1, Metallic materials - Tensile testing - Part 1: Method of test at ambient temperature EN 10002-5, Metallic materials - Tensile testing - Part 5: Method of test at elevated temperature EN 10021, General technical delivery requirements for steel products EN 10027-1, Designation systems
26、for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10045-1, Metallic materials - Charpy impact test - Part 1: Test method EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:2007, Definition of steel products EN 10088
27、-1:2005, Stainless steels - Part 1: List of stainless steels EN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes EN 10163-3, Delivery requirements for surface
28、condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections EN 10168:2004, Steel products - Inspection documents - List of information and description EN 10204, Metallic products - Types of inspection documents EN 10221, Surface quality classes for hot-rolled bars and rods - Tec
29、hnical delivery conditions CEN/TR 10261, Iron and steel - Review of available methods of chemical analysis EN 10306, Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams EN 10308, Non destructive testing - Ultrasonic testing of steel bars EN ISO 377, Steel and steel pro
30、ducts - Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) BS EN 10088-5:2009 EN 10088-5:2009 (E) 6 EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels - Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainle
31、ss steels - Corrosion test in media containing sulphuric acid (ISO 3651-2:1998) EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2005) EN ISO 9001, Quality management systems - Requirements (ISO 9001:2008) EN ISO 14284, Steel and iron - Sampling and prepara
32、tion of samples for the determination of chemical composition (ISO 14284:1996) ISO 286-1, ISO system of limits and fits Part 1: Bases of tolerances, deviations and fits 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 stainless steels the defi
33、nition in EN 10088-1:2005 applies 3.2 corrosion resisting steels steels with at least 10,5 % Cr and max. 1,20 % C if their resistance to corrosion is of primary importance 3.3 product forms the definitions in EN 10079:2007 apply 3.4 types of heat treatment the definitions in EN 10052:1993 apply 3.5
34、standard grades grades with a relatively good availability and a wider range of application 3.6 special grades grades for special use and/or with limited availability 4 Designation and ordering 4.1 Designation of steel grades The steel names and steel numbers (see Tables 2 to 5) are allocated in acc
35、ordance with EN 10027-1 and EN 10027-2 respectively. 4.2 Order designation The complete designation for ordering a product according to this European Standard shall contain the following information: a) the desired quantity; BS EN 10088-5:2009 EN 10088-5:2009 (E) 7 b) the product form (e. g. round b
36、ars, square bars or rod); c) the nominal dimensions and, where an appropriate dimensional standard is available, (see Table 7 and Annex B) the number of the standard plus any choice of requirements; d) if there is no dimensional standard, the nominal dimensions and tolerances required; e) the type o
37、f material (steel); f) the number of this European Standard; g) the steel name or steel number; h) the symbol for the desired heat treatment or cold worked condition, if for the relevant steel in the tables for the mechanical properties more than one treatment condition is covered; i) the desired co
38、ndition (see symbols in Table 7); j) verification of internal soundness, if required; k) the type of inspection certificate (3.1 or 3.2) according to EN 10204; l) regulatory marking requirements (see Annex ZA). EXAMPLE 10 t round bars of a steel grade with the name X5CrNi18-10 and the number 1.4301
39、as specified in EN 10088-5 of 50 mm diameter, dimensional tolerances as specified in EN 10060, in condition 1D (see Table 7), inspection certificate 3.1 as specified in EN 10204 and declaration of conformity: 10 t round bars EN 10060-50 Steel EN 10088-5-X5CrNi18-10+1D Inspection certificate 3.1, CE
40、or 10 t round bars EN 10060-50 Steel EN 10088-5-1.4301+1D Inspection certificate 3.1, CE 5 Classification of grades Steels covered in this European Standard are classified according to their structure into a) ferritic steels; b) martensitic steels; c) precipitation hardening steels; d) austenitic st
41、eels; e) austenitic-ferritic steels. See also Annex B to EN 10088-1:2005. BS EN 10088-5:2009 EN 10088-5:2009 (E) 8 6 Requirements 6.1 Steelmaking process Unless otherwise agreed at the time of enquiry and order, the steelmaking and manufacturing process for steels conforming to this European Standar
42、d shall be at the discretion of the manufacturer. 6.2 Delivery condition The products shall be supplied by reference to the process route given in Table 7 and, where different alternatives exist, to the treatment conditions given in Tables 8 to 18 and 20 (see also Annex A). 6.3 Chemical composition
43、6.3.1 The requirements given in Tables 2 to 5 shall apply in respect of the chemical composition according to the cast analysis. If grades other than those included in this European Standard are required for construction purposes, they shall comply with EN 10088-3 and be in conjunction with the requ
44、irements of this European Standard. 6.3.2 The product analysis may deviate from the limiting values for the cast analysis given in Tables 2 to 5 by the values listed in Table 6. 6.4 Chemical corrosion properties Referring to resistance to intergranular corrosion as defined in EN ISO 3651-2, for ferr
45、itic, austenitic and austenitic-ferritic stainless steels the specifications in Tables 8, 11 and 12 apply. EN ISO 3651-2 shall not be not applicable for testing martensitic and precipitation hardening steels. NOTE The corrosion resistance of stainless steels is very dependent on the type of environm
46、ent and can therefore not always be clearly ascertained through laboratory tests. It is therefore advisable to draw on the available experience of the use of the steels. 6.5 Mechanical properties 6.5.1 The mechanical properties at room temperature as specified in Tables 8 to 12 shall apply for hot w
47、orked products of every condition, condition 1U excluded, for cold processed products in condition 2D (excluding wire), and for each specified heat treatment condition. For cold processed products of every specified condition, condition 2D and wire excluded, and each specified heat treatment conditi
48、on, the mechanical properties at room temperature as specified in Tables 13 to 17 shall apply. For these products, the condition is the prime property with the mechanical properties secondary. If the products are to be supplied in a non-heat-treated condition, the mechanical properties specified in
49、Tables 8 to 17 shall be obtained from reference test pieces which have received the appropriate heat treatment (simulated heat treatment). For wire, the properties as specified in Table 18 shall apply. For bars which are intentionally cold work hardened in order to increase their tensile strength to a specified level, the mechanical properties at room temperature as specified in Table 20 shall apply. For these products, th