《BS EN 1335-2-2009 Office furniture-Office work chair Part2 Safety requirements.pdf》由会员分享，可在线阅读，更多相关《BS EN 1335-2-2009 Office furniture-Office work chair Part2 Safety requirements.pdf（12页珍藏版）》请在三一文库上搜索。
1、BS EN 1335-2:2009 ICS 13.180; 97.140 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Office furniture Office work chair Part 2: Safety requirements This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 Apr
2、il 2009 BSI 2009 ISBN 978 0 580 58648 4 Amendments/corrigenda issued since publication DateComments BS EN 1335-2:2009 National foreword This British Standard is the UK implementation of EN 1335-2:2009. It supersedes BS EN 1335-2:2000 which is withdrawn. The UK participation in its preparation was en
3、trusted to Technical Committee FW/0/3, Office. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance wit
4、h a British Standard cannot confer immunity from legal obligations. BS EN 1335-2:2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1335-2 April 2009 ICS 97.140Supersedes EN 1335-2:2000 English Version Office furniture - Office work chair - Part 2: Safety requirements Mobilier de bureau - Sig
5、es de travail de bureau - Partie 2: Exigences de scurit Brombel - Bro-Arbeitsstuhl - Teil 2: Sicherheitsanforderungen This European Standard was approved by CEN on 28 February 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving th
6、is European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions
7、 (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bu
8、lgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDA
9、RDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1335-2:2009: E BS EN 1335-2:2009 EN 1335-2:2009 (E) 2
10、Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Safety requirements 4 4.1 General design requirements .4 4.1.1 Corners and edges, trapping, pinching and shearing .4 4.1.2 Adjusting devices 5 4.1.3 Connections .5 4.1.4 Avoidance of soiling 5 4.2 Test sequence
11、5 4.3 Stability during use6 4.4 Rolling resistance of the unloaded chair 6 4.5 Strength and durability .6 5 Information for use 7 Annex A (normative) Loads, masses and cycles for safety tests 8 w w w . b z f x w . c o m BS EN 1335-2:2009 EN 1335-2:2009 (E) 3 Foreword This document (EN 1335-2:2009) h
12、as been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national stan
13、dards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13
14、35-2:2000. This series consist of following parts: EN 1335-1, Office furniture Office work chair Part 1: Dimensions Determination of dimensions; EN 1335-2, Office furniture Office work chair Part 2: Safety requirements; EN 1335-3, Office furniture Office work chair Part 3: Test methods. The main cha
15、nges with respect to the previous edition are listed below: a) castor durability (former 6.2) has been defined as functional test; b) foot rest stability and foot rest static load have been defined as safety test. According to the CEN/CENELEC Internal Regulations, the national standards organization
16、s of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
17、Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. w w w . b z f x w . c o m BS EN 1335-2:2009 EN 1335-2:2009 (E) 4 1 Scope This part of EN 1335 specifies the mechanical safety requirements for office work chairs. The requirements are based upon use for 8 h a day by persons weigh
18、ing up to 110 kg. For more severe conditions of use, increased requirements will be necessary. Annex A (normative) includes loads, masses and cycles for safety tests. Additional loads, masses and cycles for functional tests can be found in EN 1335-3:2009, Annex C. 2 Normative references The followin
19、g referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1335-1:2000, Office furniture Office work chair Part 1: Di
20、mensions Determination of dimensions EN 1335-3:2009, Office furniture Office work chair Part 3: Test methods EN 12529:1998, Castors and wheels Castors for furniture Castors for swivel chairs Requirements 3 Terms and definitions For the purposes of this document, the following terms and definitions a
21、pply. 3.1 castor assembly comprising a housing, one or more wheels, an axle and, if required, accessories EN 12529:1998 4 Safety requirements 4.1 General design requirements 4.1.1 Corners and edges, trapping, pinching and shearing The chair shall be so designed as to minimise the risk of injury to t
22、he user. All parts of the chair with which the user comes into contact during intended use, shall be so designed that physical injury and damage to property are avoided. These requirements are met when: a) the safety distance of accessible movable parts is either 8 mm or 25 mm in any position during
23、 movement; b) accessible corners are rounded with minimum 2 mm radius; w w w . b z f x w . c o m BS EN 1335-2:2009 EN 1335-2:2009 (E) 5 c) the edges of the seat, back rest and arm rests which are in contact with the user when sitting in the chair are rounded with minimum 2 mm radius; d) the edges of
24、 handles are rounded with minimum 2 mm radius in the direction of the force applied; e) all other edges are free from burrs and rounded or chamfered; f) the ends of accessible hollow components are closed or capped. 4.1.2 Adjusting devices Movable and adjustable parts shall be designed so that injur
25、ies and inadvertent operation are avoided. It shall be possible to operate the adjusting devices from sitting position in the chair. 4.1.3 Connections It shall not be possible for any load bearing part of the chair to come loose unintentionally. 4.1.4 Avoidance of soiling All parts which are lubrica
26、ted to assist sliding (greasing, lubricating, etc.) shall be designed to protect users from lubricant stains when in normal use. 4.2 Test sequence The same chair shall be tested in the following sequence: a) stability tests (optional); b) rolling resistance test (optional); c) seat and back rest tes
27、ts; d) foot rest static load test; e) arm rests durability test; f) arm rest downward static load test - central (see Table A.2, Footnote a); g) stability tests; h) arm rest downward static load test - central (see Table A.2, Footnote b); i) rolling resistance test. w w w . b z f x w . c o m BS EN 1
28、335-2:2009 EN 1335-2:2009 (E) 6 4.3 Stability during use The chair shall not overbalance under the following conditions: a) by pressing down on the front edge of the seat surface in the most adverse position; b) by leaning out over the arm rests; c) by leaning against the back rest; d) by sitting on
29、 the front edge. Requirement a) is fulfilled if the chair does not overbalance when tested according to 7.1.1 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard. Requirements b) and d) are fulfilled if the chair does not overbalance when tested according
30、to 7.1.2, 7.1.3, 7.1.4 and 7.1.5 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard. Requirement c) is fulfilled if the chair does not overbalance when tested according to 7.1.6 or 7.1.7 of EN 1335-3:2009 with the forces and numbers of cycles according to
31、 Table A.1 of this standard. 4.4 Rolling resistance of the unloaded chair The unloaded chair shall not roll unintentionally. This requirement is met when: a) the castors are of identical construction; b) the rolling resistance is 12 N when tested according to EN 1335-3:2009, 7.4. 4.5 Strength and du
32、rability The chair shall be constructed to ensure that it does not create a risk of injury to the user of the chair under the following conditions: a) sitting on the seat, both centrally and off-centre; b) moving forward, backwards, and sideways while sitting in the chair; c) leaning over the arm re
33、sts; d) pressing down on the arm rests while getting up from the chair. These requirements are fulfilled when after the tests specified in 7.2.1, 7.2.2, 7.2.6, 7.3.1 and 7.3.2 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard: e) there are no fractures o
34、f any member, joint or component, and f) there is no loosening of joints intended to be rigid, and g) no major structural element is significantly deformed and the chair fulfils its functions after removal of the test loads and when: w w w . b z f x w . c o m BS EN 1335-2:2009 EN 1335-2:2009 (E) 7 h
35、) after the test in 7.2.3 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard, the arm rests show no fracture. 5 Information for use Each chair shall be accompanied by information for use in the language of the country in which it will be delivered to the
36、end user. It shall contain at least the following details: a) information regarding the intended use; b) information regarding possible adjustments and chair type (see EN 1335-1:2000); c) instruction for operating the adjusting mechanisms; d) instruction for the care and maintenance of the chair; e)
37、 information regarding all adjustments; f) information for chairs with seat height adjustments with energy accumulators that only trained personnel may replace or repair seat height adjustment components with energy accumulators; g) information on the choice of castors in relation to the floor surfa
38、ce. w w w . b z f x w . c o m BS EN 1335-2:2009 EN 1335-2:2009 (E) 8 Annex A (normative) Loads, masses and cycles for safety tests Table A.1 Loads, masses and cycles for stability tests Clauses given in EN 1335-3:2009 Test Loads Cycle 7.1.1 Front edge overturning M1 27 kg 1 7.1.2 Forward overturning
39、 F1 F2 600 N 20 N 1 7.1.3 Forward overturning for chairs with foot rests F1 F2 1 100 N 20 N 1 7.1.4 Sideways overturning for chairs without arm rests F1 F2 600 N 20 N 1 7.1.5 Sideways overturning for chairs with arm rests F1 F2 F3 250 N 350 N 20 N 1 7.1.6 Rearwards overturning of chairs without back
40、 rest inclination F1 F2 600 N 192 N 1 7.1.7 Rearwards overturning of chairs with back rest inclination Number of discs: 13 1 BS EN 1335-2:2009 EN 1335-2:2009 (E) 9 Table A.2 Loads and cycles for strength and durability tests Clauses given in EN 1335-3:2009 Test Loads Cycles 7.2.1 Seat front edge sta
41、tic load test F1 1 600 N 10 7.2.2 Combined seat and back static load test F1 F2 1 600 N 560 N 10 7.2.6 Foot rest static load test F 1 300 N 10 7.3.1 Seat and back durability Step 1 Loading Point A F 1 500 N 120 000 Step 2 Loading Point C F 1 200 N 80 000 Loading Point B F 320 N Step 3 Loading Point
42、J F 1 200 N 20 000 Loading Point E F 320 N Step 4 Loading Point F F 1 200 N 20 000 Loading Point H F 320 N Step 5 Loading Point D and G (alternating) F 1 100 N 20 000 7.3.2 Arm rest durability F 400 N 60 000 7.2.3 Arm rest downward static load test central F 750 N a 5 F 900 N b 5 a This test shall b
43、e carried out before the stability tests b This test shall be carried out after the stability tests BS EN 1335-2:2009 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independen
44、t national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they pos
45、sess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identi
46、ty of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, internatio
47、nal and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ In response to orders for international standards, it is BSI policy
48、to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Va
49、rious BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7