《BS EN 10016-3 1995 拉制和（或）冷轧用的非合金钢棒.沸腾和沸腾代用低碳钢棒的特殊要求.pdf》由会员分享，可在线阅读，更多相关《BS EN 10016-3 1995 拉制和（或）冷轧用的非合金钢棒.沸腾和沸腾代用低碳钢棒的特殊要求.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10016-3:1995 Non-alloy steel rod for drawing and/or cold rolling Part 3: Specific requirements for rimmed and rimmed substitute low carbon steel rod The European Standard EN 10016-3:1994 has the status of a British Standard BS EN 10016-3:1995 This British Standard, having been
2、 prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 December 1995 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference ISE/71 Draft for comment 92/45129 DC ISB
3、N 0 580 24527 6 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ISE/71, Steel rod for wire drawing, upon which the following bodies were represented: British Steel Industry British Steel Industry (Wire Section) Process Pl
4、ant Association Welding Manufacturers Association (BEAMA) Ltd. Amendments issued since publication Amd. No.DateComments BS EN 10016-3:1995 BSI 07-1999i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 10016-33 List of referencesInside back cover BS EN 1
5、0016-3:1995 ii BSI 07-1999 National foreword This British Standard has been prepared under the direction of the Engineering Sector Board and is the English language version of EN 10016-3:1994 Non-alloy steel rod for drawing and/or cold rolling Part 3: Specific requirements for rimmed and rimmed subs
6、titute low carbon steel rod published by the European Committee for Standardization (CEN). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not
7、of itself confer immunity from legal obligations. Cross-reference Publication referred toCorresponding British Standard EN 10020:1988BS EN 10020:1991 Definition and classification of grades of steel Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN
8、 title page, pages 2 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. EUROPEAN STANDARD NORME EUROPENNEE EUROPISCHE NORM EN 10016-3 Decem
9、ber 1994 ICS 77.140.70 Descriptors: Iron and steel products, unalloyed steels, wire drawing, cold rolling, wire rod, low carbon steels, rimming steels, chemical composition, grades: quality, defects, inspection, mechanical properties English version Non-alloy steel rod for drawing and/or cold rollin
10、g Part 3: Specific requirements for rimmed and rimmed substitute low carbon steel rod Fil machine en acier non alli destin au trfilage et/ou au laminage froid Partie 3: Prescriptions spcifiques au fil machine en acier effervescent ou pseudoeffervescent bas carbone Walzdraht aus unlegiertem Stahl zum
11、 Ziehen und/oder Kaltwalzen Teil 3: Besondere Anfonderungen an Walzdraht aus unberuhigtem und ersatzunberuhigtem Stahl mit niedrigem Kohlenstoffgehalt This European Standard was approved by CEN on 1994-11-10. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate t
12、he conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists i
13、n three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies
14、of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretar
15、iat: rue de Stassart 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No. EN 10016-3:1994 E EN 10016-3:1994 BSI 07-1999 2 Foreword This European Standard EN 10016 is subdivided as follows: Part 1: General requirements; Part 2: Specific requirements for general purpose rod; Part 3: Spe
16、cific requirements for rimmed and rimmed substitute low carbon steel rod; Part 4: Specific requirements for rod for special applications. This European Standard has been drawn up by ECISS/TC 15, Wire-rod Qualities, dimensions, tolerances and specific tests, whose Secretariat is held by UNI/UNSIDER.
17、Parts 1, 2, 3 and 4 of this European Standard replace: This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1995, and conflicting national standards shall be withdrawn at the latest by June 1995.
18、According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Conte
19、nts Page Foreword2 1Scope3 2Normative references3 3Requirements3 3.1Chemical composition3 3.2Internal soundness and surface quality3 3.3Depth of surface defects3 3.4Inspection of non-metallic inclusions3 3.5Mechanical properties4 Table 1 Chemical analysis (heat analysis)4 Table 2 Permissible deviati
20、ons in the product analysis in relation to the actual heat analysis4 Table 3 Limit values for the depth of surface discontinuities4 Table 4 Tensile strength values4 EURONORM 16 (1987): Non alloy steel wire rod for cold drawing and/or cold rolling EN 10016-3:1994 BSI 07-19993 1 Scope This Part of thi
21、s European Standard is applicable to rod of low carbon, low silicon, rimmed and rimmed substitute steel with high ductility for drawing and/or cold rolling. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative r
22、eferences are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references
23、the latest edition of the publication referred to applies. EN 10016-1, Non-alloy steel rod for drawing and/or cold rolling Part 1: General requirements. EN 10020, Definition and classification of grades of steel. EN 10221, Surface quality classes for hot rolled bars and rods Technical delivery condi
24、tions. PrENV 10247, Micrographic examination of the inclusion content of steels using standard pictures. 3 Requirements For the general requirements see EN 10016-1. 3.1 Chemical composition For the heat analysis, the values shown in Table 1 apply. The permissible deviations of the product analysis i
25、n relation to the actual heat analysis are given in Table 2. 3.2 Internal soundness and surface quality The rod shall have no internal and/or surface imperfections such as: shrink holes, segregation, cracks, folds, incrustations, notches, scabs, rolling burrs, damage, which may be prejudicial to its
26、 correct use. 3.3 Depth of surface defects The rod shall not have any surface discontinuities of depth greater than the values shown in Table 3. These limit values apply for the test chosen according to EN 10016-1 (clauses 9.5.1 and 9.6.2). 3.4 Inspection of non-metallic inclusions The method for in
27、specting non-metallic inclusions and the assessment criteria for it shall be agreed at the time of ordering, as far as possible with reference to the ENV 10247 or to one of the following standards: DIN 50 602:1985 Metallographische Prufverfahren Mikroskopische Prufung von Edelstahlen auf nichtmetall
28、ische Einschlusse mit Bildreihen; NF A 04-107:1980 Produits sidrurgiques Mthode micrographique de dtermination de la teneur en inclusions non-mtalliques du fil-machine en acier non alli; UNI 3244:1980 (with annex) Esame microscopico dei materiali ferrosi Valutazione delle inclusioni non metalliche n
29、egli acciai mediante immagini tipo; ASTM E 45:1987 Standard practice for determining the inclusion content of steel. EN 10016-3:1994 4 BSI 07-1999 Table 1 Chemical analysis (heat analysis)a Table 2 Permissible deviations in the product analysis in relation to the actual heat analysis Table 3 Limit v
30、alues for the depth of surface discontinuities 3.5 Mechanical properties Unless otherwise specified at the time of ordering, rod of diameter 5,5 mm and above shall have the maximum tensile strength values shown in Table 4. Table 4 Tensile strength values Steel gradebHeat analysis Steel name Steel nu
31、mber C % max. Si % max. Mn %P % max. S % max. Cr %c max. Ni %c max. Mo % max. Cu %c max. Al %d max. N % max. C2D1 1.11850,030,050,200,35 0,0200,200,100,100,030,100,010,007 C3D1 1.11870,050,050,200,40 0,0250,250,100,100,030,150,05 C4D1 1.11880,060,100,200,45 0,0250,250,150,150,030,150,05 a Elements n
32、ot included in this table may not be added intentionally to the steel without the agreement of the purchaser, except those intended for finishing the cast. b Special non-alloy steel according to EN 10020. c The sum of the contents Cu + Ni + Cr shall not exceed: for steel grade C2D1, 0,25 %; for stee
33、l grade C3D1, 0,30 %; for steel grade C4D1, 0,35 %. d For steels grade C3D1 and C4D1 a lower maximum limit may be specified at the time of ordering. ElementSteel gradePermissible deviation in product analysis % CC2D1 C3D1C4D1 + 0,01 + 0,02 SiC2D1C3D1 C4D1 + 0,02 + 0,04 MnAll gradeso 0,05 P and SAll
34、grades+ 0,005 Class according to EN 10221 Nominal diameter dN mm Maximum permissible deptha of surface discontinuities mm C5 dN 120,17 12 dN 300,23 a The depth of surface discontinuities is measured from the actual surface of the product in a radial direction. Steel gradeMaximum tensile strength N/m
35、m2 C2D1360 C3D1360 C4D1by agreement BS EN 10016-3:1995 BSI 07-1999 List of references See national foreword. BS EN 10016-3:1995 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the
36、 UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to imp
37、rove the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax:
38、 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 02
39、0 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, Eur
40、opean and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing m
41、embers of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications.
42、 BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopyi
43、ng, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.