《BS EN 13722-2004 家具.表面光泽度的评定.pdf》由会员分享,可在线阅读,更多相关《BS EN 13722-2004 家具.表面光泽度的评定.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13722:2004 Furniture Assessment of the surface gloss The European Standard EN 13722:2004 has the status of a British Standard ICS 97.140 - - - - - - BS EN 13722:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 20 Se
2、ptember 2004 BSI 20 September 2004 ISBN 0 580 44465 1 National foreword This British Standard is the official English language version of EN 13722:2004. The UK participation in its preparation was entrusted to Technical Committee FW/1, Common test methods for furniture, which has the responsibility
3、to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “Internationa
4、l Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British S
5、tandard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developm
6、ents and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issue
7、d since publication Amd. No. DateComments - - - - - - e - - - - - - - -3 - E- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - W W D - - - - - - - - - - - - EN 13722:2004 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions .4 4 Principle5 5 Appara
8、tus .5 6 Preparation and conditioning of test units .5 7 Calibration of glossmeter .5 8 Test Procedure.5 8.1 General5 8.2 Textured and/or open grain surfaces 6 8.3 Other surfaces6 8.4 Expression of results 6 9 Test report8 - - - - - - EN 13722:2004 (E) 3 Foreword This document (EN 13722:2004) has be
9、en prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2005, and conflicting national standards
10、 shall be withdrawn at the latest by January 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, G
11、reece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. - - - - - - EN 13722:2004 (E) 4 1 Scope This document specifies a method for the assessment of the surface gloss of
12、 furniture surfaces using three reflectometer geometries, 20, 60 or 85 and relates to rigid surfaces of all finished products regardless of materials, except for finishes on leather and fabrics, which are excluded from this document. The test is intended to be carried out on finished furniture, but
13、can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test. It is not applicable for finishes on some metallic paints and pearly coatings. 2 Normative references The following referenc
14、ed documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 2813, Paints and varnishes - Determination of specular gloss of
15、non-metallic paint films at 20, 60 and 85 (ISO 2813:1994, including Technical Corrigendum 1:1997) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 specular gloss ratio of the luminous flux reflected from an object in the specular direction for
16、 a specified source and receptor angle to the luminous flux reflected from glass with a refractive index of 1,567 in the specular direction 3.2 test unit finished item of furniture 3.3 Test surface part of the test unit, where the test area is included 3.4 test panel panel produced in the same way a
17、s the test surface; it shall be used when it is not possible to carry out the test directly on the test surface 3.5 test area area under the equipment, where the measurement is carried out 3.6 pearly coatings coating with pearly additives. The pearly additives act like microscopy mirrors reflecting
18、and transferring the light in several directions - - - - - - EN 13722:2004 (E) 5 3.7 textured surface profiled or uneven surface 3.8 open grain surface surface where the grains/pores are not completely filled by the coating material 4 Principle The specular gloss of the test unit/test panel shall be
19、 measured in various directions, using a glossmeter with the specified geometry. 5 Apparatus Glossmeter as specified in EN ISO 2813. 6 Preparation and conditioning of test units The test unit/test panel shall be stored for not less than four weeks at a temperature not less than 15 oC and not more th
20、an 30 oC with free access of air. The test unit /test panel shall be kept in a room without direct light exposure. Conditioning shall begin one week before testing and shall be carried out in air at a temperature of (23 + 2) C and relative humidity of (50 5) %. The conditioning can be a part of the
21、four weeks above. The test surface shall be cleaned with a soft, clean, lint-free cloth before the test. The test surface shall be substantially flat and of sufficient size to take the measurements. 7 Calibration of glossmeter Before carrying out any tests, calibrate the glossmeter according to EN I
22、SO 2813 or the instructions of the glossmeter manufacturer. Calibration shall be carried out at the start of each period of operation and at intervals short enough to maintain the glossmeter accuracy according to the manufacturers instructions. To define the specular gloss scale, polished black glas
23、s with a refractive index of 1,567 is equal to a value of 100 for geometries of 20, 60 and 85. 8 Test Procedure 8.1 General Measurements shall be carried out by using glossmeter(s) with the specified geometries and according to the following procedure: Measure the specular gloss using the 60 geometr
24、y method. - - - - - - EN 13722:2004 (E) 6 If the result (see 8.4) is 70 units (high specular gloss), additional measurements shall be carried out using the 20 geometry method. NOTE 1 The 20 geometry method, which uses a smaller receptor aperture, is intended to obtain improved differentiation of hig
25、h specular gloss. If the result (see 8.4) is 10 units (low specular gloss), additional measurements shall be carried out using the 85 geometry method. NOTE 2 The 85 geometry method, which uses a larger receptor aperture, is intended to obtain improved differentiation of low specular gloss. The same
26、geometry shall be used for all the measurements on a test unit determination of the specular gloss. 8.2 Textured and/or open grain surfaces Using the glossmeter, take four measurements in the directions shown in Figure 1. 8.3 Other surfaces Using the glossmeter, take four measurements in the directi
27、ons shown in Figure 2. 8.4 Expression of results The result is expressed in gloss units. Calculate the mean value of the four values. If the spread of the values exceeds 10 gloss units or 20 % of the mean value, the measurement shall be considered invalid and the procedure shall be repeated using fo
28、ur different points of the test surface. If the result fails again, the specular surface gloss can not be assessed. - - - - - - EN 13722:2004 (E) 7 Key 1 Glossmeter direction ( ) Not correct () Correct Figure 1 Textured ad open grain surfaces Key 1 Glossmeter direction Figure 2 Other surfaces - - -
29、- - - EN 13722:2004 (E) 8 9 Test report The test report shall include at least the following information: a) Reference to this document; b) unit or panel tested, including relevant data (wherever possible the substrate, the finishing system and the finishing date shall be identified); c) geometry us
30、ed, i.e. 20, 60 or 85 d) individual test results and the mean values; e) any deviations from this document ; f) name and address of the test facility; g) date of test. - - - - - - blank - - - - - - BS EN 13722:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the
31、 independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure th
32、at they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible,
33、 the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI,
34、 international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy
35、to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Va
36、rious BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receiv
37、e substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also