《BS EN 1929-4-2005 蓝筐手推车 第4部分：有或无儿童乘坐设备、还有承载物品设备有运载乘客设备上使用的蓝筐式手推车的要求和.pdf》由会员分享，可在线阅读，更多相关《BS EN 1929-4-2005 蓝筐手推车 第4部分：有或无儿童乘坐设备、还有承载物品设备有运载乘客设备上使用的蓝筐式手推车的要求和.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ? 1929-4:2005 Basket trolleys Part 4: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility, intended to be used on passenger conveyors The European Standard EN 1929-4:2005 has the status of a British
2、 Standard ICS 97.130.30 ? BS EN 1929-4:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 13 October 2005 BSI 13 October 2005 ISBN 0 580 46557 8 National foreword This British Standard is the official English language version of EN 1929-4:2
3、005. The UK participation in its preparation was entrusted to Technical Committee CW/51, Shopping trolleys, which has the responsibility to: Leg room The UK committee would like to draw the users attention to BS EN 1929-1, 4.2.1.4, which specifies adequate space for the trolley users stride. In this
4、 standard, BS EN 1929-1, 4.2.1.4 should be observed in this respect. Additional goods carrying facilities In its present form this standard permits the contents of some of the additional goods carrying facilities to be insecure and likely to fall onto the floor. Manufacturers and users of this stand
5、ard should be aware that this could be hazardous to health and safety. Manufacturers should take steps to ensure that their designs hold contents securely. This could be achieved by ensuring that there are appropriate vertical sides of suitable height on the additional goods carrying facilities. Des
6、igns ought to ensure that no goods could be kicked out by a child sitting in the child seat. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in
7、 this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a
8、 contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or propos
9、als for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright notice displayed i
10、n this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1929-4 April 2005 ICS 97.130.30 English version Basket trolleys - Part 4: Requirements and tests for basket trolleys with additi
11、onal goods carrying facility(ies), with or without a child carrying facility, intended to be used on passenger conveyors Chariots dachat corbeille - Partie 4 : Prescriptions et essais pour les chariots dachat corbeille et dispositif(s) supplmentaire(s) de dpose de marchandises, avec ou sans sige pou
12、r enfant, destins tre utiliss sur trottoirs roulants Einkaufswagen - Teil 4: Anforderungen und Prfungen fr Einkaufswagen mit zustzlichen Abstelleinrichtungen fr Waren, mit oder ohne Kindersitz, geeignet fr den Gebrauch auf Personenfahrsteigen This European Standard was approved by CEN on 14 February
13、 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtain
14、ed on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secret
15、ariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Port
16、ugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CENAll rights of exploitation in any form and by any means reserve
17、d worldwide for CEN national Members. Ref. No. EN 1929-4:2005: E EN 1929-4:2005 (E) 2 Contents Page Foreword3 1Scope 5 2Normative references5 3Terms and definitions .5 4Safety 5 5Inspections and tests6 6Signboards, use instructions and marking.6 7Tests7 Bibliography9 ? EN 1929-4:2005 (E) 3 Foreword
18、This document (EN 1929-4:2005) has been prepared by Technical Committee CEN/TC 291 “ Self service shopping trolleys” , the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at th
19、e latest by October 2005, and conflicting national standards shall be withdrawn at the latest by October 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, C
20、zech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. ? EN 1929-4:2005 (E) 4 Introduction This document is a
21、part of a series of standards currently under preparation by CEN/TC 291. The parts of this series are: EN 1929-1 Basket trolleys Part 1: Requirements and tests for basket trolleys with or without a child carrying facility EN 1929-2 Basket trolleys Part 2: Requirements, tests and inspection for baske
22、t trolleys with or without a child carrying facility, intended to be used on passenger conveyors EN 1929-3 Basket trolleys Part 3: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility EN 1929-4 Basket trolleys Part 4: Requ
23、irements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility, intended to be used on passenger conveyors prEN 1929-6: Basket trolleys Part 6: Requirements, tests and inspection for basket trolleys with base trays for Do It Yourself ma
24、rkets intended to be used on passenger conveyors EN 1929-7: Basket trolleys Part 7: Requirements and tests for basket trolleys with baby and child carrying facilities ? EN 1929-4:2005 (E) 5 1 Scope This document specifies requirements for the construction, performance, testing and safety specificati
25、ons for general purpose self-service basket trolleys, with additional goods carrying facility(ies), with or without a child carrying facility, intended to be used on passenger conveyors, accompanied by a user. 2 Normative references The following referenced documents are indispensable for the applic
26、ation of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 115, Safety rules for the construction and installation of escalators and passenger conveyors EN 1929-1:1998, Bas
27、ket trolleys Part 1: Requirements and tests for basket trolleys with or without a child carrying facility EN 1929-2:2004, Basket trolleys Part 2: Requirements, tests and inspection for basket trolleys with or without a child carrying facility, intended to be used on passenger conveyors EN 1929-3:200
28、5, Basket trolleys Part 3: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility 3 Terms and definitions For the purposes of this document the terms and definitions given in EN 1929-2:2004 and EN 1929-3:2005 and the followi
29、ng apply. 3.1 basket trolley with goods carrying facility(ies) intended to be used on passenger conveyors manually driven trolley with goods carrying facility(ies), suitable for use on a passenger conveyor 4 Safety 4.1 Generalities Trolleys covered by this document are intended to be used on passeng
30、er conveyors conforming with EN 115 and shall comply with EN 1929-3, with the exception of subclause 4.1 only for the diameter of the wheels (in Table 1 paragraph line 4.2.2 rolling quality of EN 1929- 1:1998, where the diameter of the wheels shall be not less than 120 mm), subclause 5.5, Clause 6.
31、4.2 Total loading mass When used on a passenger conveyor, the total loading mass of the trolley shall not exceed 160 kg. 4.3 Space between the trolley and passenger conveyor The difference between the overall width of the trolley and the nominal width of the passenger conveyor shall be not less than
32、 400 mm. ? EN 1929-4:2005 (E) 6 4.4 Maintaining the trolley on the passenger conveyor The trolley shall be equipped with a device that maintains it in a stopped position in the absence of any outside intervention. The diameter of the wheels shall not be less than 120 mm. 4.5 Stability The trolley sh
33、all not overturn, when tested in accordance with: 7.1.2, up to and including 16 in the ascending and descending direction; 7.1.3, up to and including 10 in the sideways direction. 4.6 Stability when exiting the passenger conveyor The trolley shall not overturn in the descending direction when encoun
34、tering the comb at the exit of the passenger conveyor. This requirement is considered to be met when the trolley conforms to test 7.3. 5 Inspections and tests See 5 of EN 1929-2:2004. 6 Signboards, use instructions and marking 6.1 Signboards and use instructions See 6.1 of EN 1929-2:2004. 6.2 Markin
35、g Trolleys shall have a pictogram conforming to Figure 2 in paragraph 6.1 of EN 1929-2:2004 of dimensions not less than 20 mm x 20 mm and permanently affixed to the handle. The maximum basket load shall be clearly visible to the user. An identification plate including the following indications shall
36、 be visibly and permanently affixed to each trolley: manufacturers name or trade mark; address of the manufacturer; commercial name of the trolley and indicated volume (in accordance with 4.4 of EN 1929-1:1998); calculated volume in litres (in accordance with 3.10 of EN 1929-1:1998); maximum load in
37、 kilograms (in accordance with 3.11 of EN 1929-1:1998 and 4.2 of this document); load of every goods carrying facility in kilograms (see 3.7 of EN 1929-3:2005); month and year of manufacture; number and date of this document. The maximum load of the child carrying facility for type D trolley, i.e. 1
38、5 kg (see 4.9 of EN 1929-1:1998) shall be clearly displayed on the trolley. ? EN 1929-4:2005 (E) 7 7 Tests 7.1 Stability tests 7.1.1 General Stability tests shall be carried out with the additional load(s) simulating the goods carrying facility(ies) (see 4.2.4.2 of EN 1929-3:2005), as described in T
39、able 1: on type C trolleys with the basket empty, on type D trolleys with the basket empty and with a load simulating a child in the child carrying facility as described in 5.4 of EN 1929-1:1998. Table 1 Loading of goods carrying facility(ies) for the stability tests Goods carrying facility Lateral
40、stability Longitudinal stability forward Longitudinal stability backward Below the basket (see Figure 1, position a in 3.1 of EN 1929-3:2005) Empty Empty Empty Behind the basket (see Figure 1, position b in 3.1 of EN 1929-3:2005) Empty Empty Loaded as described in 4.2.4.2 of EN 1929- 3:2005 In conne
41、ction with the back rest (see Figure 1, position c in 3.1 of EN 1929-3:2005) Loaded as described in 4.2.4.2 of EN 1929- 3:2005 Empty Loaded as described in 4.2.4.2 of EN 1929- 3:2005 At the front of the basket (see Figure 1, position d in 3.1 of EN 1929- 3:2005) Loaded as described in 4.2.4.2 of EN
42、1929- 3:2005 Loaded as described in 4.2.4.2 of EN 1929- 3:2005 Empty Above the bottom of the basket (see Figure 1, position e in 3.1 of EN 1929-3:2005) Loaded as described in 4.2.4.2 of EN 1929- 3:2005 Loaded as described in 4.2.4.2 of EN 1929- 3:2005 Empty ? EN 1929-4:2005 (E) 8 7.1.2 Longitudinal
43、stability test The test device shall consist of a tilting platform equipped with a 20 mm high strip placed parallel to the axis of inclination and acting as a limit stop for the trolley wheels. The test shall be carried out at room temperature. Place the swivelling castors in the least stable positi
44、on. Tilt the trolley on the test apparatus, in the ascending and descending direction to an angle of 16. If the trolley does not overturn at an angle up to and including 16, then it shall be deemed to conform to this document. 7.1.3 Lateral stability test The test device shall consist of a tilting p
45、latform equipped with a 20 mm high strip placed parallel to the axis of inclination and acting as a limit stop for the trolley wheels. The test shall be carried out at room temperature. Place the swivelling castors in the least stable position. Tilt the trolley on the test apparatus, to either side,
46、 to an angle of 10. If the trolley does not overturn at an angle up to and including 10, then it shall be deemed to conform to this document. 7.2 Test for maintaining trolleys on passenger conveyors See 7.2 of EN 1929-2:2004. 7.3 Toppling test when exiting from the passenger conveyor For trolleys wi
47、th goods carrying facility at the front of the basket (see Figure 1, position d in 3.1 of EN 1929-3:2005), load only the goods carrying facility as described in 4.2.4.2 of EN 1929-3:2005. For trolleys without goods carrying facility at the front of the basket (see Figure 1, positions a, b, c, e in 3
48、.1 of EN 1929-3:2005), place only a 400 mm x 300 mm x 300 mm cuboid with a homogenous mass of 24 kg in the basket of the trolley, in the most unfavourable position, i.e. the centre of gravity being as near as possible to the front face of the trolley. The test apparatus shall consist of a tilting pl
49、atform equipped with a 20 mm high strip placed parallel to the axis of inclination and acting as a limit stop for the trolley wheels. The test shall be carried out at room temperature. Place the trolley on the test platform with the swivelling castors directed towards the rear of the trolley. Tilt the trolley facing in the descending