《BS EN 635-2-1995 Plywood — Classification by surface appearance — Part 2 Hardwood.pdf》由会员分享，可在线阅读，更多相关《BS EN 635-2-1995 Plywood — Classification by surface appearance — Part 2 Hardwood.pdf（14页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 635-2:1995 Incorporating Amendment No. 1 Plywood Classification by surface appearance Part 2: Hardwood The European Standard EN 635-2:1995 has the status of a British Standard ICS 79.060.10 BS EN 635-2:1995 This British Standard, having been prepared under the direction of the
2、 Sector Board for Building and Civil Engineering, was published under the authority of the Standards Board and comes into effect on 15 December 1995 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference B/541 Draft for comment 92/114811 DC ISBN 0 580 24769
3、 4 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee B/541, Wood based panels, upon which the following bodies were represented: APA/Engineered Wood Association Association of British Plywood and Veneer Manufacturers Britis
4、h Woodworking Federation Council of the Forest Industries of British Columbia Department of the Environment (Building Research Establishment) Finnish Plywood International Flat Roofing Contractors Advisory Board Forestry Commission Furniture Industry Research Association Institution of Structural En
5、gineers Local Authority Organizations Mineral Bonded Board Products Federation National Federation of Roofing Contractors National House-Building Council National Panel Products Association Royal Institute of British Architects Structural Board Association Timber Research and Development Association
6、 Timber Trade Federation Wood Panel Industries Federation Zurich Municipal Building Guarantee Co-opted members Amendments issued since publication Amd. No.DateComments 9124June 1996Indicated by a sideline in the margin BS EN 635-2:1995 BSI 07-1999i Contents Page Committees responsibleInside front co
7、ver National forewordii Foreword2 Text of EN 635-23 List of referencesInside back cover BS EN 635-2:1995 ii BSI 07-1999 National foreword This British Standard has been prepared by Technical Committee B/541 and is the English language version of EN 635-2:1995 Plywood Classification by surface appear
8、ance Part 2: Hardwood, published by the European Committee for Standardization (CEN). EN 635-2 was produced as a result of international discussions in which the United Kingdom took an active part. BS EN 635-1, BS EN 635-2 and BS EN 635-3 together supersede BS 6566-6:1985, which will be withdrawn in
9、 accordance with CEN provisions within 6 months of completion of the full package of standards covering plywood and related test methods. These standards are: The method of classification used in BS EN 635-2 and BS EN 635-3 is similar to that of BS 6566-6:1985. But although the appearance classes in
10、 BS EN 635-2 and BS EN 635-3 are identified as E, I, II, III and IV, these classes do not correspond exactly to the appearance classes E, I, II, III and IV of BS 6566-6. The BS EN 635 standards are thus not technically equivalent to BS 6566-6. NOTEEN 635-2 makes informative reference to EN 636-1, EN
11、 636-2 and EN 636-3 which are currently in preparation. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from lega
12、l obligations. EN 310 EN 313-1 EN 313-2 EN 314-1 EN 314-2 EN 315 EN 322 EN 323 EN 324-1 EN 324-2 EN 325 EN 635-1 EN 635-2 EN 635-3 EN 636-1 EN 636-2 EN 636-3 EN 1072 EN 1084 Cross-reference Publication referred toCorresponding British Standard EN 635-1:1994BS EN 635 Plywood Classification by surface
13、 appearance Part 1:1995 General Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This wi
14、ll be indicated in the amendment table on the inside front cover. ? EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 635-2 May 1995 ICS 79.060.10 Descriptors: Wood board, plywood, deciduous timber, classifications, appearance, defects English version Plywood Classification by surface appearance
15、Part 2: Hardwood Contreplaqu Classification selon l aspect des faces Partie 2: Bois feuillus Sperrholz Klassifizierung nach dem Aussehen der Oberflche Teil 2: Laubholz This European Standard was approved by CEN on 1995-04-14. CEN members are bound to comply with the CEN/CENELEC Internal Regulations
16、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European
17、Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national
18、bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central S
19、ecretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members Ref. No. EN 635-2:1995 E ? EN 635-2:1995 BSI 07-1999 2 Foreword This European Standard has been prepared by the Technical Co
20、mmittee CEN/TC 112, Wood-based panels, of which the secretariat is held by DIN. This standard is one of a series of standards for the classification of plywood by surface appearance. The other Parts of this series are listed in clause 2 and Annex A. This European Standard shall be given the status o
21、f a national standard, either by publication of an identical text or by endorsement, at the latest by November 1995, and conflicting national standards shall be withdrawn at the latest by November 1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement
22、 this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Contents Page Foreword2 1Scope3 2Normative references3 3Classification by surface appearance3 3.1 A
23、ppearance classes3 3.2 Permissible characteristics and defects3 Annex A (informative) Bibliography7 Table 1 Classification according to characteristics inherent in wood4 Table 2 Classification according to manufacturing defects6 ? EN 635-2:1995 BSI 07-19993 1 Scope This European Standard specifies t
24、he nature and limits of characteristics inherent in wood and manufacturing defects enabling the visual assessment of the plywood for allocation to an appearance class. This classification is a contribution to assessing the finishing suitability of plywood. This Part of EN 635 applies to plywood, the
25、 surface veneers of which are made from hardwood1) species. It does not apply to overlaid panels. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text a
26、nd the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.
27、EN 635-1, Plywood Classification by surface appearance Part 1: General. 3 Classification by surface appearance 3.1 Appearance classes Assessment of characteristics and defects for determination of appearance class shall be carried out in accordance with EN 635-1. Surface classification shall be base
28、d on the permissible characteristics and defects within each of the appearance classes as specified in 3.2. NOTEGuidance on selection of finishing for each appearance class is given in ENV 635-4. 3.2 Permissible characteristics and defects Each surface shall be individually assigned to one of the ap
29、pearance classes E, I, II, III, IV, as defined by the permissible characteristics and defects indicated in Table 1 and Table 2. 1)In English, this means conventionally broadleaved species. ? EN 635-2:1995 4 BSI 07-1999 3.2.1 Classification according to characteristics inherent in wood Table 1 Classi
30、fication according to characteristics inherent in wood Categories of characteristicsAppearance class EIIIIIIIV 3.2.1.1 Pin knotsaPractically absent 3/m2 permitted Permitted 3.2.1.2 Sound intergrown knotsPermitted up to an individual diameter of: 15 mm provided their cumulative diameter does not exce
31、ed 30 mm/m2 35 mm50 mmPermitted, but see note Such knots may have splits provided they are very slightslight 3.2.1.3 Unsound or non-adhering knots and knot holes Permitted up to an individual diameter of:Permitted, but see note 6 mm if filled and up to a number of 2/m2 5 mm if unrepaired, 25 mm if f
32、illed and up to a number of 3/m2 40 mm 3.2.1.4 SplitsOpenPermitted if less than: 1/101/31/3Permitted, but see note of panel length up to an individual width of: 3 mm5 mm20mm and up to a number of: 3/m3/m3/m of panel width if properly filledif unrepaired, or unlimited if all filled ClosedPermitted ?
33、EN 635-2:1995 BSI 07-19995 Table 1 Classification according to characteristics inherent in wood Categories of characteristicsAppearance class EIIIIIIIV 3.2.1.5 Abnormalities due to insects, marine borers and parasitic plants Not permittedNot permittedMarks of parasitic plants not permitted. Insects
34、and marine borer holes permitted up to a: Permitted, but see note diameter of 3 mm vertically to the plane of the panel up to 10/m2 width of 15 mm and a length of 60 mm up to 3/m2 3.2.1.6 InbarkNot permittedPermitted up to a width of:Permitted, but see note 5 mm if properly filled25 mm 3.2.1.7 Irreg
35、ularities in the structure of the wood Practically absent PermittedPermitted if very slightif slight 3.2.1.8 Discoloration which is not wood destroying Permitted if low contrastPermitted 3.2.1.9 Fungal decay, which is wood destroying Not permittedNot permitted 3.2.1.10 Other characteristicsPractical
36、ly absent To be considered under the category which they most closely resemble NOTECharacteristics inherent to the wood are permitted provided that they do not impair the serviceability of the panel. aPin knots: sound intergrown knots of no more than 3 mm diameter. ? EN 635-2:1995 6 BSI 07-1999 3.2.
37、2 Classification according to manufacturing defects Table 2 Classification according to manufacturing defects Categories of defectsAppearance class EIIIIIIIV 3.2.2.1 Open jointsNot permittedNot permittedPermitted up to a width of: 3 mm5 mm25 mm and up to a number of: 1/m2/munlimited of panel width w
38、ith joints filled if more than 1 mm in width unfilledunfilled 3.2.2.2 OverlapsNot permittedPermitted up to a number of 1/m2 and up to 100 mm length Permitted up to a number of 2/m2 Permitted but see note 3.2.2.3 BlistersNot permitted 3.2.2.4 Hollows, imprints and bumpsNot permittedPermitted if sligh
39、tPermitted 3.2.2.5 RoughnessNot permittedPermitted if slightPermitted 3.2.2.6 Sanding throughNot permittedPermitted up to an extent of: 1 %5 % (but see note) of panel surface 3.2.2.7 Glue penetrationNot permittedPermitted: if slight and occasionalup to an extent of 5 % of the panel surface Permitted
40、 but see note 3.2.2.8 Foreign particlesNot permittedFerrous particles not permitted 3.2.2.9 Repairs: a) patches; b) shims; c) synthetic fillers. Practically without defects Permitted if properly made and tightly filled up to a number of: 3/m26/m2 unlimited Not permittedNot permittedPermitted within
41、the limits specified in the categories unlimited 3.2.2.10 Defects at the edges of the panel due to sanding or sawing Practically without defects Permitted up to:Permitted but see note 2 mm5 mm from the edge 3.2.2.11 Other characteristics or defectsTo be considered under the category which they most
42、closely resemble NOTEManufacturing defects are permitted provided that they do not impair the serviceability of the panel. EN 635-2:1995 BSI 07-19997 Annex A (informative) Bibliography EN 313-1, Plywood Classification and terminology Part 1: Classification. EN 313-2, Plywood Classification and termi
43、nology Part 2: Terminology. EN 635-1, Plywood Classification by surface appearance Part 1: General. EN 635-2, Plywood Classification by surface appearance Part 2: Hardwood. ENV 635-4, Guideline Plywood Classification by surface appearance Part 4: Parameters of ability for finishing2). EN 636-1, Plyw
44、ood Specifications Part 1: Requirements for plywood for use in dry conditions. EN 636-2, Plywood Specifications Part 2: Requirements for plywood for use in humid conditions. EN 636-3, Plywood Specifications Part 3: Requirements for plywood for use in exterior conditions. 2)At present at the draft st
45、age. 8 blank BS EN 635-2:1995 BSI 07-1999 List of references See national foreword. BS EN 635-2:1995 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Eu
46、rope and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our pro
47、ducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers
48、members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996
49、7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also a