《EN 1929-2-2004蓝筐式手推车 第2部分：有或无儿童乘坐设备可在乘运送装置上使用的蓝筐式手推车的要求、试验和检验.pdf》由会员分享，可在线阅读，更多相关《EN 1929-2-2004蓝筐式手推车 第2部分：有或无儿童乘坐设备可在乘运送装置上使用的蓝筐式手推车的要求、试验和检验.pdf（17页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1929-2:2004 Basket trolleys Part 2: Requirements, tests and inspection for basket trolleys with or without a child carrying facility, intended to be used on passenger conveyors The European Standard EN 1929-2:2004 has the status of a British Standard ICS 97.130.30 ? - - - BS E
2、N 1929-2:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 13 December 2004 BSI 13 December 2004 ISBN 0 580 45052 X National foreword This British Standard is the official English language version of EN 1929-2:2004. The UK participation in
3、 its preparation was entrusted to Technical Committee CW/51, Self-service shopping trolleys, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Additional information In the United Kingdom, in order to facilitate emerge
4、ncy evacuation in certain buildings, the width of the passenger conveyor may need to be wider than specified in this standard. The appropriate UK “Health and Safety Regulations” and “Building and Fire Regulations” must be consulted and observed. Cross-references The British Standards which implement
5、 international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does no
6、t purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European co
7、mmittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 t
8、o 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments - - - EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1929-2 December 2004 ICS 97.130.30 Englis
9、h version Basket trolleys - Part 2: Requirements, tests and inspection for basket trolleys with or without a child carrying facility, intended to be used on passenger conveyors Chariots dachat corbeille - Partie 2 : Prescriptions, essais et inspection pour les chariots dachat corbeille, avec ou sans
10、 sige pour enfant, destins tre utiliss sur les trottoirs roulants Einkaufswagen - Teil 2: Anforderungen, Prfungen und Instandhaltung fr Einkaufswagen mit oder ohne Kindersitz, geeignet fr den Gebrauch auf Personenfahrteigen This European Standard was approved by CEN on 16 August 2004. CEN members ar
11、e bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to
12、the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same st
13、atus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slove
14、nia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN n
15、ational Members. Ref. No. EN 1929-2:2004: E - - - EN 1929-2:2004 (E) 2 Contents Page Foreword3 1 Scope 5 2 Normative references5 3 Terms and definitions .5 4 Safety 5 4.1 Generalities 5 4.2 Total loading mass 5 4.3 Space between the trolley and the passenger conveyor.5 4.4 Maintaining the trolley on
16、 the passenger conveyor.5 4.5 Stability.6 4.6 Stability when exiting the passenger conveyor .6 5 Inspections and tests6 5.1 General6 5.1.1 At the delivery of the trolleys .6 5.1.2 After major modifications .6 5.1.3 Periodically.6 5.2 Register.7 5.3 Commissioning, use of, maintenance and repair.7 5.4
17、 Technical requirements for the use of trolleys on passenger conveyors.7 6 Signboards, use instructions and marking.8 6.1 Signboards and use instructions.8 6.2 Marking.8 7 Tests9 7.1 Stability tests9 7.1.1 Longitudinal stability test .9 7.1.2 Lateral stability test.9 7.2 Test for maintaining trolley
18、s on passenger conveyors.10 7.3 Toppling test when exiting from the passenger conveyor11 Bibliography12 - - - EN 1929-2:2004 (E) 3 Foreword This document (EN 1929-2:2004) has been prepared by Technical Committee CEN/TC 291 “Self-service shopping trolleys”, the secretariat of which is held by BSI. Th
19、is European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. According to the CEN/CENELEC Internal Regulations, the na
20、tional standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
21、Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. - - - EN 1929-2:2004 (E) 4 Introduction This document is a part of a series of standards currently under preparation by CEN/TC 291. The parts of this series are: EN 1929-1, Basket trolleys Part 1: Requirements and tests for
22、 basket trolleys with or without a child carrying facility; EN 1929-2, Basket trolleys Part 2: Requirements, tests and inspection for basket trolleys with or without a child carrying facility, intended to be used on passenger conveyors; prEN 1929-3, Basket trolleys Part 3: Requirements and tests for
23、 basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility; prEN 1929-4, Basket trolleys Part 4: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility, intended to be used on pa
24、ssenger conveyors; prEN 1929-5, Basket trolleys Part 5: Requirements and tests for basket trolleys with base trays for Do It Yourself markets; prEN 1929-6, Basket trolleys Part 6: Requirements, tests and inspection for basket trolleys with base trays for Do It Yourself markets, intended to be used o
25、n passenger conveyors; prEN 1929-7, Basket trolleys Part 7: Requirements and tests for basket trolleys with baby and child carrying facilities. - - - EN 1929-2:2004 (E) 5 1 Scope This document specifies requirements for the construction, performance, testing and safety specifications for general pur
26、pose self service basket trolleys, with or without a child carrying facility, intended to be used on passenger conveyors, accompanied by a user. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition ci
27、ted applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 115:1995, Safety rules for the construction and installation of escalators and passenger conveyors. EN 1929-1:1998, Basket trolleys Part 1: Requirements and tests for basket trol
28、leys with or without a child carrying facility. ISO 3864 (both parts), Safety colours and safety signs. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1929-1:1998 and the following apply. 3.1 basket trolley intended to be used on passenger conveyors
29、manually driven trolley, suitable for use on a passenger conveyor 4 Safety 4.1 Generalities Trolleys covered by this document are intended to be used on passenger conveyors conforming with EN 115 and shall comply with EN 1929-1, with the exception of 5.4, 6 and 4.2.2 only for the diameter of the whe
30、els. 4.2 Total loading mass When used on a passenger conveyor, the total loading mass of the trolley shall not exceed 160 kg. 4.3 Space between the trolley and the passenger conveyor The trolley complying with this document is intended to be used on passenger conveyors for which the nominal width is
31、 not less than 400 mm greater than the overall width of the trolley. 4.4 Maintaining the trolley on the passenger conveyor The trolley shall be equipped with a device that maintains it in a stopped position in the absence of any outside intervention. The diameter of the wheels shall not be less than
32、 120 mm. EN 1929-2:2004 (E) 6 4.5 Stability The trolley shall not overturn, when tested in accordance with: 7.1.1, up to and including 16 in the ascending and descending direction; 7.1.2, up to and including 10 in the sideways direction. 4.6 Stability when exiting the passenger conveyor The trolley
33、shall not overturn in the descending direction when encountering the comb at the exit of the passenger conveyor. This requirement is considered to be met when the trolley conforms to test 7.3. 5 Inspections and tests 5.1 General The manufacturer shall provide written information on inspections and t
34、ests that should include at least the following information: 5.1.1 At the delivery of the trolleys Inspections and operating tests should be carried out by a competent person together with the passenger conveyors on which they will be used. They should include: a) a general visual inspection of the
35、passenger conveyors, especially broken teeth of the comb and dirt; b) a general visual inspection of the trolleys; c) the efficiency of the devices for maintaining laden and unladen trolleys on passenger conveyors; d) the efficiency of the devices for maintaining laden and unladen trolleys when the
36、emergency stop devices have been activated; e) the verification of the ability of laden and unladen trolleys to enter and exit passenger conveyors. 5.1.2 After major modifications Inspections and delivery acceptance tests (5.1.1) should be repeated after major modifications. Major modifications are:
37、 a) for the passenger conveyor: see 16.2.2 “Inspection and test after major modifications“ of EN 115:1995; b) for the trolleys: structural modifications; use of components or accessories other than the original ones, in particular changing of wheels or of devices for maintaining trolleys in a stoppe
38、d position. NOTE Replacement of parts by parts of the same design is not considered to be a major modification. 5.1.3 Periodically Periodic inspections and tests according to 5.1.1 should be carried out at least every six months. They should include the condition of the castors of all the trolleys.
39、- - - EN 1929-2:2004 (E) 7 5.2 Register The technical characteristics of the interface between the passenger conveyor installations and trolleys should be recorded in a register, at the latest at the time of commissioning of the trolleys. This register should be kept up to date by a competent safety
40、 officer and should include: a) a technical record of the trolley commissioning date and characteristics, especially the total loading mass, major modifications or component changes; b) dated reports of examinations, inspections, maintenance and tests, together with comments, as well as reports of a
41、ny accidents. This register should be at the disposal of the maintenance department and of the safety manager (the national authority can indicate with reference to their regulations, who is responsible for the register). 5.3 Commissioning, use of, maintenance and repair The manufacturer shall provi
42、de instructions for commissioning, use of, maintenance and repair of the trolleys, as well as the frequency of the periodic tests (at least every six months). The trolleys should be regularly maintained by competent persons. 5.4 Technical requirements for the use of trolleys on passenger conveyors B
43、asket trolleys covered by this document are intended to be used on passenger conveyors conforming to EN 115, the maximum nominal speed of which is 0,5 m/s, and the landing zones are within the limits given in Figure 1, so as to facilitate the transition of trolleys and passengers and to meet the req
44、uirements of sub-clause 0.5.3 of EN 115:1995. Slant angle of comb teeth in reference to belts or pallets tread surface 15; height between belts or pallets tread surface and ground H 55 mm; distance between the height of the belts or pallets tread surface at the level of the comb intersection point (
45、P) and the junction of the ground (A) L 500 mm. Key P Comb intersection point A Junction of the ground Figure 1 Comb tooth of passenger conveyors EN 1929-2:2004 (E) 8 6 Signboards, use instructions and marking 6.1 Signboards and use instructions The manufacturer shall provide written recommendations
46、 to the purchaser concerning fixing visible and permanent signboards close to the entrance of the conveyor. These recommendations shall include at least the following: - A pictogram in white on green background (see ISO 3864) conforming to Figure 2 with minimum dimensions (80 80) mm fixed close to t
47、he entrance of the passenger conveyor accompanied by the following instruction “Hold the handle continuously“. - Instructions in characters that are easy to read in the language of the country in which the trolleys are to be used. Figure 1 Pictogram at entry to passenger conveyor and on the trolley
48、handle - Following additional instructions affixed: the maximum basket load; use only with trolleys carrying the appropriate pictogram (Figure 2); the trolley should be held at all times on the passenger conveyor. Other instructions may be used, such as: the load should not exceed the sides of the t
49、rolley. 6.2 Marking Trolleys shall have a pictogram conforming to Figure 2, of dimensions not less than (20 20) mm, permanently affixed to the handle. The maximum basket load shall be clearly visible to the user. An identification plate including the following indications shall be visibly and permanently affixed to each trolley: E