《EN 10017-2004 拉制和或冷轧用非合金钢棒材 尺寸和公差.pdf》由会员分享，可在线阅读，更多相关《EN 10017-2004 拉制和或冷轧用非合金钢棒材 尺寸和公差.pdf（18页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10017:2004 Steel rod for drawing and/or cold rolling Dimensions and tolerances The European Standard EN 10017:2004 has the status of a British Standard ICS 77.140.65 BS EN 10017:2004 This British Standard was published under the authority of the Standards Policy and Strategy C
2、ommittee on 27 October 2004 BSI 27 October 2004 ISBN 0 580 44654 9 National foreword This British Standard is the official English language version of EN 10017:2004. It supersedes BS 4956:1973 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/71, St
3、eel rods for wire drawing, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in th
4、e BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible
5、for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK i
6、nterests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 15 and a back cover. The BSI copyright notice displayed in this document indicates wh
7、en the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10017 October 2004 ICS 77.140.65 Supersedes EURONORM 17:1970 English version Steel rod for drawing and/or cold rolling - Dimensions and tolerances Fil machi
8、ne en acier non alli destin au trfilage et/ou laminage froid - Dimensions et tolrances Walzdraht aus Stahl zum Ziehen und/oder Kaltwalzen - Mae und Grenzabmae This European Standard was approved by CEN on 9 July 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which st
9、ipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard
10、 exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standard
11、s bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITT
12、EE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10017:2004: E EN 10017:2004 (E) 2 Cont
13、ents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions4 4 Information to be supplied by the purchaser .4 4.1 Information to be supplied by the purchaser .4 4.2 Examples 4 5 Nominal sections and nominal mass.5 6 Dimensions and tolerances6 6.1 Round rod (Fig. 1)6 6.2 Square rod
14、(Fig. 2) .8 6.3 Rectangular rod (Fig. 3).9 6.4 Hexagonal Rod (Fig. 4)12 7 Mass of coils and checks on dimensional tolerances.14 8 Claims .14 Bibliography15 EN 10017:2004 (E) 3 Foreword This document (EN 10017:2004) has been prepared by Technical Committee ECISS/TC 15 “Wire rod - Qualities, dimension
15、s, tolerances and specific tests”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the
16、 latest by April 2005. This document supersedes EURONORM 17 (1970). This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech
17、 Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10017:2004 (E) 4 1 Scope This document specifies the dim
18、ensions, the tolerances, the nominal cross-section and the nominal mass of steel rod for drawing. This document concerns round, square, rectangular and hexagonal rod in steel grades specified in European Standards. 2 Normative references The following referenced documents are indispensable for the a
19、pplication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. The requirements of this document rule when they differ from those in the standards and documents referred to b
20、elow. EN 10021, General technical delivery requirements for steel and iron products EN 10079:1992, Definition of steel products 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10079:1992 apply. 4 Information to be supplied by the purchaser 4.1 Informa
21、tion to be supplied by the purchaser The following information shall be supplied by the purchaser at the time of enquiry and order, to enable the supplier to comply satisfactorily with the requirements of this document: a) quantity to be delivered b) product denomination (rod) c) section (round, squ
22、are, rectangular, hexagonal) d) reference to this document e) nominal dimensions in millimetres f) information included in the quality product European Standard 4.2 Examples Round rod with a diameter of 10 mm in steel C10D according EN 10016-2: EXAMPLE 1 Round rod EN 10017 - 10 - EN 10016-2 - C10D E
23、N 10017:2004 (E) 5 Rectangular rod with a width of 30 mm and thickness 5 mm in steel C3D1 according EN 10016-3: EXAMPLE 2 Rectangular rod EN 10017 - 30 x 5 - EN 10016-3 - C3D1 Hexagonal rod with a wrench opening of 10 mm in steel C70D2 according EN 10016-4: EXAMPLE 3 Hexagonal rod EN 10017 - 10 - EN
24、 10016-4 - C70D2 5 Nominal sections and nominal mass The values for sections and mass are shown in Tables 1 to 4 and are given as a guide. They have been calculated and rounded off on the basis of nominal sizes and a density of 7,85 kg/dm3. For stainless steels to calculate the nominal mass, densiti
25、es should be obtained from EN 10088-1. EN 10017:2004 (E) 6 6 Dimensions and tolerances 6.1 Round rod (Fig. 1) Figure 1 Round rod Table 1 Dimensions, tolerances, nominal section and nominal mass Nominal diameter d Tolerance on diameter Tolerance on ovality a Nominal section Nominal mass (mm) (mm) (mm
26、) (mm2) (kg/m) 5 0,3 19,63 0,154 5,5 0,3 23,76 0,187 6 0,3 28,27 0,222 6,5 0,3 33,18 0,26 7 0,3 38,48 0,302 7,5 0,3 44,18 0,347 8 0,3 50,26 0,395 8,5 0,3 56,74 0,445 9 0,3 63,62 0,499 9,5 0,3 70,88 0,556 10 0,4 78,54 0,617 10,5 0,4 86,59 0,68 11 0,4 95,03 0,746 11,5 0,4 103,9 0,816 12 0,4 113,1 0,88
27、8 12,5 0,4 122,7 0,963 13 0,4 132,7 1,04 13,5 0,4 143,1 1,12 14 0,4 153,9 1,21 14,5 0,4 165,1 1,3 15 0,4 176,7 1,39 15,5 0,4 188,7 1,48 16 0,5 201,1 1,58 16,5 0,5 213,8 1,68 17 0,5 227,0 1,78 17,5 0,5 240,5 1,89 18 0,5 254,5 2,00 18,5 0,5 268,8 2,11 19 0,5 283,5 2,23 19,5 0,5 80 % of the total toler
28、ance on the diameter 298,6 2,34 (Continued) EN 10017:2004 (E) 7 Table 1 Dimensions, tolerances, nominal section and nominal mass (concluded) Nominal diameter d Tolerance on diameter Tolerance on ovality a Nominal section Nominal mass (mm) (mm) (mm) (mm2) (kg/m) 20 0,5 314,2 2,47 21 0,5 346,3 2,72 22
29、 0,5 380,1 2,98 23 0,5 415,5 3,26 24 0,5 452,4 3,55 25 0,5 490,9 3,85 26 0,6 530,9 4,17 27 0,6 572,6 4,49 28 0,6 615,7 4,83 29 0,6 660,5 5,18 30 0,6 706,9 5,55 31 0,6 754,4 5,93 32 0,6 803,8 6,31 33 0,6 854,9 6,71 34 0,6 907,5 7,13 35 0,6 961,6 7,55 36 0,6 1017,4 7,99 37 0,6 1074,7 8,44 38 0,6 1133,
30、5 8,90 39 0,6 1194 9,38 40 0,8 1256 9,87 41 0,8 1319,6 10,36 42 0,8 1384,7 10,88 43 0,8 1451,5 11,40 44 0,8 1519,7 11,93 45 0,8 1589.6 12,49 46 0,8 1661,1 13,05 47 0,8 1734,1 13,62 48 0,8 1808,7 14,20 49 0,8 1884,8 14,80 50 0,8 80 % of the total tolerance on the diameter 1962,5 15,41 a Difference be
31、tween the maximum and minimum diameter on the same cross section EN 10017:2004 (E) 8 6.2 Square rod (Fig. 2) Figure 2 Square rod Table 1 Dimensions, tolerances, nominal section and nominal mass Nominal side a Tolerance on the side Difference between maximum side and minimum side a Nominal section No
32、minal mass (mm) (mm) (mm) (mm2) (kg/m) 16 0,5 256,0 2,01 17 0,5 289,0 2,27 18 0,5 324,0 2,54 19 0,5 361,0 2,83 20 0,5 400,0 3,14 21 0,5 441,0 3,46 22 0,5 484,0 3,80 23 0,5 529,0 4,15 24 0,5 576,0 4,52 25 0,5 625,0 4,91 26 0,6 676,0 5,31 27 0,6 729,0 5,72 28 0,6 784,0 6,15 29 0,6 841,0 6,60 30 0,6 90
33、0,0 7,10 31 0,6 961,0 7,54 32 0,6 80 % of the total tolerance on the side 1024,0 8,04 a On the same cross section EN 10017:2004 (E) 9 6.3 Rectangular rod (Fig. 3) Figure 3 Rectangular rod Table 3 Dimensions, tolerances, nominal section and nominal mass Tolerances on b x d nominal b d Nominal section
34、 Nominal mass (mm) (mm) (mm) (mm2) (kg/m) 16 x 11 0,5 0,4 176,0 1,38 16 x 12 0,5 0,4 192,0 1,51 17 x 11 0,5 0,4 187,0 1,47 17 x 12 0,5 0,4 204,0 1,6 18 x 10 0,5 0,4 180,0 1,41 18 x 11 0,5 0,4 198,0 1,55 18 x 12 0,5 0,4 216,0 1,70 19 x 10 0,5 0,4 190,0 1,49 19 x 11 0,5 0,4 209,0 1,64 19 x 12 0,5 0,4
35、228,0 1,79 19 x 13 0,5 0,4 247,0 1,94 20 x 9 0,5 0,4 180,0 1,41 20 x 10 0,5 0,4 200,0 1,57 20 x 11 0,5 0,4 220,0 1,73 20 x 12 0,5 0,4 240,0 1,88 20 x 13 0,5 0,4 260,0 2,04 20 x 14 0,5 0,4 280,0 2,20 20 x 15 0,5 0,4 300,0 2,36 20 x 16 0,5 0,4 320,0 2,51 (continued) EN 10017:2004 (E) 10 Table 3 Dimens
36、ions, tolerances, nominal section and nominal mass Tolerances on b x d nominal b d Nominal section Nominal mass (mm) (mm) (mm) (mm2) (kg/m) 22 x 8 0,6 0,4 176,0 1,38 22 x 9 0,6 0,4 198,0 1,55 22 x 10 0,6 0,4 220,0 1,73 22 x 11 0,6 0,4 242,0 1,90 22 x 12 0,6 0,4 264,0 2,07 22 x 13 0,6 0,4 286,0 2,25
37、22 x 14 0,6 0,4 308,0 2,42 22 x 15 0,6 0,4 330,0 2,59 22 x 16 0,6 0,4 352,0 2,76 22 x 17 0,6 0,4 374,0 2,94 25 x 7 0,6 0,3 175,0 1,37 25 x 8 0,6 0,4 200,0 1,57 25 x 9 0,6 0,4 225,0 1,77 25 x 10 0,6 0,4 250,0 1,96 25 x 11 0,6 0,4 275,0 2,16 25 x 12 0,6 0,4 300,0 2,36 25 x 13 0,6 0,4 325,0 2,55 25 x 1
38、4 0,6 0,4 350,0 2,75 25 x 15 0,6 0,4 375,0 2,94 25 x 16 0,6 0,4 400,0 3,14 25 x 17 0,6 0,4 425,0 3,34 26 x 7 0,6 0,3 182,0 1,43 26 x 8 0,6 0,4 208,0 1,63 26 x 9 0,6 0,4 234,0 1,84 26 x 10 0,6 0,4 260,0 2,04 26 x 11 0,6 0,4 286,0 2,25 26 x 12 0,6 0,4 312,0 2,45 26 x 13 0,6 0,4 338,0 2,65 26 x 14 0,6
39、0,4 364,0 2,86 26 x 15 0,6 0,4 390,0 3,06 26 x 16 0,6 0,4 416,0 3,27 26 x 17 0,6 0,4 442,0 3,47 26 x 18 0,6 0,4 468,0 3,67 26 x 20 0,6 0,4 520,0 4,08 (continued) EN 10017:2004 (E) 11 Table 3 Dimensions, tolerances, nominal section and nominal mass (concluded) Tolerances on b x d nominal b d Nominal
40、section Nominal mass (mm) (mm) (mm) (mm2) (kg/m) 28 x 6,5 0,6 0,3 182,0 1,43 28 x 7 0,6 0,3 196,0 1,54 28 x 8 0,6 0,4 224,0 1,76 28 x 9 0,6 0,4 252,0 1,98 29 x 10 0,6 0,4 280,0 2,20 28 x 11 0,6 0,4 308,0 2,42 28 x 12 0,6 0,4 336,0 2,64 28 x 13 0,6 0,4 364,0 2,86 28 x 14 0,6 0,4 392,0 3,08 28 x 15 0,
41、6 0,4 420,0 3,30 30 x 6 0,6 0,3 180,0 1,41 30 x 6,5 1,6 0,3 195,0 1,53 30 x 7 0,6 0,3 210,0 1,65 30 x 8 0,6 0,4 240,0 1,88 30 x 9 0,6 0,4 270,0 2,12 30 x 10 0,6 0,4 300,0 2,36 30 x 11 0,6 0,4 330,0 2,59 30 x 12 0,6 0,4 360,0 2,83 30 x 13 0,6 0,4 390,0 3,06 30 x 14 0,6 0,4 420,0 3,30 30 x 15 0,6 0,4
42、450,0 3,53 30 x 16 0,6 0,4 480,0 3,77 30 x 17 0,6 0,4 510,0 4,00 30 x 18 0,6 0,4 540,0 4,24 30 x 20 0,6 0,4 600,0 4,71 EN 10017:2004 (E) 12 6.4 Hexagonal Rod (Fig. 4) Figure 4 Hexagonal rod Table 4 Dimensions, tolerances, nominal section and nominal mass Nominal wrench opening a Tolerance on wrench
43、opening Difference between maximum and minimum wrench opening a Nominal section Nominal mass (mm) (mm) (mm) (mm2) (kg/m) 8 0,4 55,43 0,435 9 0,4 70,15 0,551 10 0,4 86,60 0,680 11 0,4 104,8 0,823 12 0,4 124,7 0,979 13 0,4 146,4 1,15 14 0,4 169,7 1,33 15 0,4 194,9 1,53 16 0,5 221,7 1,74 17 0,5 250,3 1
44、,96 18 0,5 280,6 2,20 19 0,5 312,6 2,45 20 0,5 346,4 2,72 22 0,5 419,2 3,29 23 0,5 458,1 3,60 24 0,5 498,8 3,92 25 0,5 80 % of the total tolerance on the wrench opening 541,3 4,25 (continued) EN 10017:2004 (E) 13 Table 4 Dimensions, tolerances, nominal section and nominal mass (Concluded) Nominal wr
45、ench opening a Tolerance on wrench opening Difference between maximum and minimum wrench opening a Nominal section Nominal mass (mm) (mm) (mm) (mm2) (kg/m) 26 0,6 585,4 4,60 27 0,6 631,3 4,96 28 0,6 679,0 5,33 29 0,6 728,3 5,71 30 0,6 779,4 6,12 31 0,6 831,9 6,53 32 0,6 886,8 6,96 33 0,8 943,1 7,40
46、34 0,8 1001,1 7,86 35 0,8 1060,9 8,33 36 0,8 1122,4 8,81 37 0,8 1185,6 9,31 38 0,8 1250,5 9,82 39 0,8 1317.2 10,34 40 0,8 80 % of the total tolerance on the wrench opening 1385,6 10,88 a On the same cross section. EN 10017:2004 (E) 14 7 Mass of coils and checks on dimensional tolerances 7.1 Mass and
47、 tolerance on mass of individual coils may be agreed between manufacturer and purchaser. In any delivery it is permitted that a maximum of 5% of the coils may be supplied with a mass less than the specified minimum mass. 7.2 Tolerances are checked on a cross section of a specimen, which is a length
48、of rod taken from the test unit. The number of specimens to be taken from the test unit should be agreed at the time of the order. It should also be agreed the number of specimens to be taken from the test unit when complementary tests will be made. In the event of a dispute the dimensions of the ro
49、d shall be measured at a distance from the ends of the coil greater than those included in Table 5. Table 5 Distance from the ends Diameter (or diameter of the equivalent section) of the rod (mm) Distance from the ends of the coil (m) 5 7 13 18 23 28 to to to to to to 6,5 12,5 17,5 22 27 50 5 4 3 2 1,5 1 8 Claims For claims and their outcome see EN 10021. EN 10017:2004 (E) 15 Bibliography 1 EN 10088-1, Stainless steels - Part 1: List of stainless steel BS EN 10017:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standa