《07-30163197-DC.pdf》由会员分享，可在线阅读，更多相关《07-30163197-DC.pdf（23页珍藏版）》请在三一文库上搜索。
1、a Date: 2 March 2007 Origin: International Latest date for receipt of comments: 30 June 2007 Project no.: 2007/00536 Responsible committee: MCE/18/-/4 Connectors and associated components Interested committees: Title: Draft BS ISO 12151-1 Connections for hydraulic fluid power and general use Hose fi
2、ttings Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSISO12151-1 : 1999 (R05) and partially supersede NONE . If you are aware of a current national standard which may be a
3、ffected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 June 2007. This draft is issued to allow comments from interested parties; all comments will be given consideration prior
4、 to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organizatio
5、n for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards
6、 are also available from BSI Customer Services. British Standards on CD or Online are available from British Standards Publishing Sales Limited. Tel: 01344 404409 or email bsonlinetechindex.co.uk. Information on the co-operating organizations represented on the committees referenced above may be obt
7、ained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 01608 647900 Responsible Commi
8、ttee Secretary: Ms Yvonne Pearman (BSI) E-mail: yvonnebfpa.co.uk Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 6.1 DPC: 07/30163197 DC Licensed Copy: London South Bank University, London South Bank Univ
9、ersity, Sat Mar 17 03:52:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are invited and will assist in the preparation of the consequent standard. Comments su
10、bmitted will be reviewed by the relevant BSI committee before sending the consensus UK vote and comments to the international secretariat, which will then decide appropriate action on the draft and the comments received. If no comments are received to the contrary, then the UK will approve this draf
11、t. If the international standard is approved, it is possible the text will be published as an identical British Standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ens
12、ure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Com
13、ments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as give
14、n in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at:http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB C
15、lause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend
16、to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and
17、Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank University, Sat Mar 17 03:52:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE RE
18、FERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
19、WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. DRAFT INTERNATIONAL STANDARD ISO/DIS 12151-1 International Organization for Standardization, 2007 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 131/SC 4 Voting begins on: 2007-03-05 Secretariat:
20、 ANSI Voting terminates on: 2007-08-05 Connections for hydraulic fluid power and general use Hose fittings Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends Raccordements pour transmissions hydrauliques et applications gnrales Flexibles de raccordement Partie 1: Flexibles avec embouts join
21、ts faciaux toriques conformes lISO 8434-3 Revision of first edition (ISO 12151-1:1999) ICS 23.040.70; 23.100.40 In accordance with the provisions of Council Resolution 15/1993 this document is circulated in the English language only. Conformment aux dispositions de la Rsolution du Conseil 15/1993, c
22、e document est distribu en version anglaise seulement. To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent docum
23、ent est distribu tel quil est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Licensed Copy: London South Bank University, London South Bank University, Sat Mar 17 03:52:36 GMT+00:00 2007, Uncontrol
24、led Copy, (c) BSI ISO/DIS 12151-1 ii ISO 2007 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed
25、on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products u
26、sed to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please
27、 inform the Central Secretariat at the address given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, st
28、ored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of t
29、he requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. Licensed Copy: London South Bank University
30、, London South Bank University, Sat Mar 17 03:52:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ISO/DIS 12151-1 ISO 2007 All rights reserved iii Contents Page Foreword iv Introduction.v 1 Scope1 2 Normative references2 3 Terms and definitions.2 4 Performance requirements.2 5 Designation of hose fitti
31、ngs.3 6 Design.3 7 Manufacture.4 7.1 Construction4 7.2 Workmanship.4 7.3 Finish4 7.4 Fitting protection.4 8 Assembly instructions4 9 Procurement information .5 10 Marking.5 11 Identification statement (reference to this part of ISO 12151)5 Annex A (informative) Illustrations of applications for shor
32、t, medium and long ISO 12151-1 hose fittings14 Bibliography15 Licensed Copy: London South Bank University, London South Bank University, Sat Mar 17 03:52:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ISO/DIS 12151-1 ISO 2007 All rights reservediv Foreword ISO (the International Organization for Stan
33、dardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right
34、 to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International S
35、tandards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an
36、International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Intern
37、ational Standard ISO 12151-1 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components. This second edition would cancel and replace the first edition (ISO 12151-1:1999), which would have been technically revised. ISO 12151
38、 consists of the following parts, under the general title Connections for hydraulic fluid power and general use Hose fittings: Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends Part 2: Hose fittings with ISO 8434-1 and 8434-4 24 degree cone connector ends with O-rings Part 3: Hose fittings
39、 with ISO 6162-1 or ISO 6162-2 flange ends Part 4: Hose fittings with ISO 6149-2 and ISO 6149-3 stud ends Part 5: Hose fittings with ISO 8434-2 37 degree flared ends Part 6: Hose fittings with ISO 8434-6 60 degree cone ends Annex A of this part of ISO 12151 is for information only. Licensed Copy: Lo
40、ndon South Bank University, London South Bank University, Sat Mar 17 03:52:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ISO/DIS 12151-1 ISO 2007 All rights reserved In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. In g
41、eneral applications, the fluid may be conveyed under pressure. v Introduction Components are connected through their ports by stud ends on fluid conductor connectors to tubes/pipes or to hose fittings and hoses. Licensed Copy: London South Bank University, London South Bank University, Sat Mar 17 03
42、:52:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Licensed Copy: London South Bank University, London South Bank University, Sat Mar 17 03:52:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI DRAFT INTERNATIONAL STANDARD ISO/DIS 12151-1 1 1 Scope This part of ISO 12151 specifies the general and dimensio
43、nal requirements for the design and performance of hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal hose inside diameters of 6,3 mm to 38 mm inclusive, in accordance with ISO 4397. NOTE 1 Materials other than carbon steel may be supplied as ag
44、reed between the manufacturer and user. NOTE 2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC 22), see ISO 4038, ISO 4039-1 and ISO 4039-2. These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid p
45、ower systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hose. ISO 2007 All rights reserved Key 1 Hose fitting 2 Port in accordance with ISO 6149-1 3 O-ring seal 4 Adapter in accordance with ISO 8434-3 5 Nut 6 O-ring seal Figure 1
46、Typical example of hose fitting connection with O-ring face seal end 1 2 3 4 6 5 Connections for hydraulic fluid power and general use Hose fittings Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends Licensed Copy: London South Bank University, London South Bank University, Sat Mar 17 03:52
47、:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ISO/DIS 12151-1 ISO 2007 All rights reserved2 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edit
48、ion of the referenced document (including any amendments) applies. ISO 68-2, ISO general purpose screw threads Basic profile Part 2: Inch screw threads ISO 263, ISO inch screw threads - General plan and selection for screws, bolts and nuts - Diameter range 0.06 to 6 in ISO 4397, Fluid power systems
49、and components Connectors and associated components Nominal outside diameters of tubes and nominal inside diameters of hoses ISO 4759-1:2000, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 55981), Fluid power systems and components Vocabulary ISO 5864, ISO inch screw threads Allowances and t