《08-30165388-DC.pdf》由会员分享，可在线阅读，更多相关《08-30165388-DC.pdf（13页珍藏版）》请在三一文库上搜索。
1、a Date: 10 October 2008 Origin: International Latest date for receipt of comments: 31 January 2009 Project no.: 2007/01063 Responsible committee: MTE/18 Tools tips and inserts for cutting applications Interested committees: Title: Draft BS ISO 5610-2 Tool holders with rectangular shank for indexable
2、 inserts Part 2: Style A Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WA
3、RNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 January 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. Se
4、e overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to
5、 dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-o
6、perating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Servic
7、e on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30165388 DC Lic
8、ensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are invited and will assist in the preparation
9、of the consequent standard. Comments submitted will be reviewed by the relevant BSI committee before sending the consensus UK vote and comments to the international secretariat, which will then decide appropriate action on the draft and the comments received. If the international standard is approve
10、d, it is possible the text will be published as an identical British Standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and
11、 appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0
12、 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information
13、 on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragra
14、ph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no
15、connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. L
16、icensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH. IN ADDITION
17、 TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. RECIPIENTS OF THIS DRA
18、FT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL STANDARD ISO/DIS 5610-2 International Organization for Standardization, 2008 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION O
19、RGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 29/SC 9 Voting begins on: 2008-10-06 Secretariat: DIN Voting terminates on: 2009-03-06 Tool holders with rectangular shank for indexable inserts Part 2: Style A Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 2: Forme A (Revisio
20、n of ISO 5610:1998) ICS 25.100.01 To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent document est distribu tel
21、quil est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI ISO/DIS 5610-2 ii ISO 2008 A
22、ll rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In down
23、loading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the
24、 General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address
25、given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in an
26、y form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale
27、 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Unco
28、ntrolled Copy, (c) BSI ISO/DIS 5610-2 ISO 2008 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO techn
29、ical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
30、with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft In
31、ternational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document
32、may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5610-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials. This second/third/. edition cancels
33、 and replaces the first/second/. edition (), clause(s) / subclause(s) / table(s) / figure(s) / annex(es) of which has / have been technically revised. ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey,
34、correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style T Part 14: Style H Part 15: Style V Licensed Copy: London Sout
35、h Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI DRAFT INTERNATIONAL STANDARD ISO/DIS 5610-2 ISO 2008 All rights reserved 1 1 Scope This Internationa
36、l Standard applies to tool holders with rectangular shank, style A, i.e. with straight shank and cutting edge angle r = 90 for side cutting. These tool holders are primarily intended for indexable inserts made of hardmetal or other cutting materials to be mounted by clamping and to be used for turni
37、ng operations. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3002-1:
38、1982, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers ISO 5608:1995, Turning and copying tool holders and cartridges for indexable inserts Designation ISO 5610-1, Tool holders with
39、rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions ISO 5610-3, Tool holders with rectangular shank for indexable inserts Part 3: Style B ISO 5610-4, Tool holders with rectangular shank for indexable inserts Part 4: Style D ISO 5610-5, Tool hol
40、ders with rectangular shank for indexable inserts Part 5: Style F ISO 5610-6, Tool holders with rectangular shank for indexable inserts Part 6: Style G ISO 5610-7, Tool holders with rectangular shank for indexable inserts Part 7: Style J ISO 5610-8, Tool holders with rectangular shank for indexable
41、inserts Part 8: Style K ISO 5610-9, Tool holders with rectangular shank for indexable inserts Part 9: Style L ISO 5610-10, Tool holders with rectangular shank for indexable inserts Part 10: Style N ISO 5610-11, Tool holders with rectangular shank for indexable inserts Part 11: Style R ISO 5610-12, T
42、ool holders with rectangular shank for indexable inserts Part 12: Style S ISO 5610-13, Tool holders with rectangular shank for indexable inserts Part 13: Style T ISO 5610-14, Tool holders with rectangular shank for indexable inserts Part 14: Style H ISO 5610-15, Tool holders with rectangular shank f
43、or indexable inserts Part 15: Style V 3 Dimensions The tool holders need not comply with the pictorial representation, only the dimensions given shall be observed. For determination of dimensions h1, f and l1 see Part 1 of this International Standard. For explanation of the designation code for tool
44、 holders, see ISO 5608:1995. Tool holders with rectangular shank for indexable inserts Part 2: Style A Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI ISO/DIS 5610-2 2 ISO 2008 All rights reserved 3.1 Tool holder style A for rhombic in
45、dexable insert shape C NOTE The figure shows a right hand tool holder (R); left hand tool holder (L) laterally reversed. a Inclination angle n b Rake angle n Figure 1 Tool holder style A for rhombic indexable insert (C) Table 1 Dimensions in millimetres h1 b l3 f h2 l1a l2 sb Symbola js13 h13 5 , 0
46、0 + h13 k16 max. SCACR 0808 06 SCACL 0808 06 8 8 6,4 8,5 8 12 2,38 SCACR 1010 06 SCACL 1010 06 10 10 6,4 10,5 10 12 2,38 a For the selection of length l1, the dash can be replaced by the dimensions of ISO 5610-1, Table 2. Letter symbols identifying the tool length, see ISO 5608, Table 6. b Insert th
47、ickness without shim, if any. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI ISO/DIS 5610-2 ISO 2008 All rights reserved 3 3.2 Tool holder style A for triangular indexable insert shape T NOTE The figure shows a right hand tool holder
48、(R); left hand tool holder (L) laterally reversed. a Inclination angle n b Rake angle n Figure 2 Tool holder style A for triangular indexable insert (T) Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:54, Uncontrolled Copy, (c) BSI ISO/DIS 5610-2 4 ISO 2008 All rights reserved Table 2 Dimensions in millimetres h1 b l3 f h2 l1a l2 sb Symbola js13 h13 5 , 0 0 + h13 k16 max. STACR 1212 11 STACL 1212 11 2,38 PTANR 1212 11 PTANL 1212 11 CTAPR 1212 11 CTAPL 1212 11 12 12 11 12,5 12 25 3,18 STACR 1616 11 STACL 1616 11