《07-30171469-DC.pdf》由会员分享，可在线阅读，更多相关《07-30171469-DC.pdf（15页珍藏版）》请在三一文库上搜索。
1、Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 7.0 DPC: 07/30171469 DC Date: 14 December 2007 Origin: European Latest date for receipt of comments: 31 March 2008 Project no.: 2007/02449 Responsible commi
2、ttee: FSH/22 Fire resistance tests Interested committees: FSH/22/3 Title: Draft BS EN 15080-15 Extended application of results from fire resistance tests Part 15: Linear joint seals Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE
3、 and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 March 2008. This draft is is
4、sued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under
5、 the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Servic
6、es, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-r
7、eferences The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 020 8996 7252 Responsible Committee Secretary: Ms Sheila OReilly (BSI) E-mail: sheila
8、.oreillybsi- a Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome
9、 and will assist in the preparation of the consequent British Standard. If no comments are received to the contrary, then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even
10、if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should
11、submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be su
12、bmitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submit
13、ted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/www.b
14、si- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Sec
15、retariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been e
16、ncountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. b Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy,
17、 (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM DRAFT prEN 15080-15 December 2007 ICS English Version Extended application of results from fire resistance tests - Part 15: Linear joint seals This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the
18、Technical Committee CEN/TC 127. If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This draft European Standard
19、 was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the
20、 national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland
21、 and United Kingdom. Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation. Warning : This document is not a European Standard. It is distributed for review and comments. It is s
22、ubject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any m
23、eans reserved worldwide for CEN national Members. Ref. No. prEN 15080-15:2007: E Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI prEN 15080-15:2007 (E) 2 Contents Page Foreword3 1 Scope.4 2 Normative references
24、 4 3 Definitions.4 4 Extended application principles.8 4.1 General8 4.2 Principles common to all generic seal types9 5 Extended application report .10 5.1 Contents of the extended application report 10 5.2 Review of the extended application report .11 Annex A (normative) Extended application princip
25、les for generic joint seal types.12 Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI prEN 15080-15:2007 (E) 3 Foreword This document (prEN 15080-15:2007) has been prepared by Technical Committee CEN/TC 127 “Fire
26、 safety in buildings”, the secretariat of which is held by BSI. This document is currently submitted to the CEN Enquiry. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of 89/106/EEC.
27、 EN 15080 “Extended application of results from fire resistance tests Part 15: Linear joint seals“ consists of the following Parts: Part ?: Non-loadbearing walls Part ?: Non-loadbearing sandwich panels ceilings Part 8: Beams (in course of preparation) Part 10: F R ducts Part 11: Dampers Part 12: Loa
28、dbearing masonry walls Part 13: Load bearing Columns Part 14: Penetration seals (in course of preparation) Part 15: Linear Joint Seals Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI prEN 15080-15:2007 (E) 4 1
29、Scope The purpose of this document is to provide the principles and guidance for the preparation of extended application documents for linear joint sealing systems tested in accordance with EN 1366-4. The field of the extended application document is additional to the direct field of application giv
30、en within EN 1366-4 and may be applied to or based on a single test, or a number of tests, which provide the relevant information for the formulation of an extended application. It should be noted that this standard provides general guidance on the likely effects of a change. It gives no guidance as
31、 to the magnitude, nor how this magnitude is evaluated. It should be noted that at present there is considered to be insufficient test evidence and experience to determine extended application rules for mechanical metal seals. All designs and configurations must, therefore, be the subject of a suita
32、ble test program. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amen
33、dments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 1363-1, Fire resistance tests Part 1: General require
34、ments EN 1363-2, Fire resistance tests Part 2: Alternative and additional procedures EN 1366-3, Fire resistance tests for service installations Part 3: Penetration seals EN 1366-4, Fire resistance tests for service installations Part 4: Linear joint seals EN 13501-1, Fire classification of construct
35、ion products and building elements Part 1: Classification using test data from reaction to fire tests EN 13501-2, Fire classification of construction products and building elements Part 2: Classification using data from fire resistance tests, (excluding products for use in ventilation systems) EN IS
36、O 13943, Fire safety Vocabulary 3 Definitions For the purposes of this document the definitions given in EN 1363-1, EN 1363-2, EN 1366-3, EN 1366-4, EN 13501-1, EN 13501-2 and EN ISO 13943, together with the following, apply: 3.1 fabric seal a seal comprising a woven fabric, usually glass cloth or s
37、imilar, which may be used in a combination with other material, such as metal facings etc. to provide a composite seal Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI prEN 15080-15:2007 (E) 5 3.2 foam seal a se
38、al made from a one, two or three component expanding foam (expands during application), applied in-situ 3.3 joint depth the overall distance between the exposed and unexposed faces across the thickness of the separating element see Figure 1 3.4 joint face framing additional substrate incorporated be
39、tween the supporting construction and the joint seal 3.5 joint width the distance between the two adjacent faces of the building element(s) see Figure 1 3.6 mineral wool based seal a seal comprised in the majority, or entirety of glass, stone or ceramic wool, which do not rely on a mastic component
40、for their primary fire resistance performance 3.7 mortar based seal a seal comprising a cementitious or gypsum based compound, together with other filler materials, usually mixed on site with water to achieve the required workability 3.8 movement joint a joint between adjacent building elements or w
41、ithin a building element designed to accommodate a degree of movement of greater than 7.5 % (such as deflection, thermal movement or seismic) 3.9 non-movement joint a joint between adjacent building elements or within a building element not designed to accommodate movement greater than 7.5 % (such a
42、s those designed to accommodate construction tolerances or irregularities of fit) 3.10 seal depth the shortest distance between the exposed and unexposed surfaces of the seal see Figure 1 3.11 seal width the width of the seal in the non-installed condition (e.g. uncompressed solid seals, see Figure
43、1A) or the width of the installed seal where it is equal to or different from the joint width (e.g. overlap) see Figure 1B and C 3.12 sealant/mastic/putty based seal a seal comprising a sealant/mastic/putty material, generally in conjunction with a backing material, inserted into the joint Licensed
44、Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI prEN 15080-15:2007 (E) 6 3.13 strip based seal a preformed seal normally inserted into the joint and held in place by friction or by means of an adhesive. These may also i
45、nclude impregnated or multi component (composite, laminated) seals such as a combination of foam tape with strips of intumescent material 3.14 surface mounted strip a surface mounted seal applied over the joint to completely cover and overlap the joint. Usually mechanically fixed to the surface of t
46、he building element Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI prEN 15080-15:2007 (E) 7 1 2 3 4 1 3 4 5 1 5 3 4 Key Linear joint seal 3 Joint depth 1 Seal Width 4 Joint width 2 Direction of compression 5 S
47、eal depth Figure 1 Definition of seal depth, joint depth and joint width for different types of seals Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 01:59:55 GMT+00:00 2008, Uncontrolled Copy, (c) BSI prEN 15080-15:2007 (E) 8 Key Joint face framing Figure 2 Exa
48、mples for a joint face framing 4 Extended application principles 4.1 General Due to the diverse nature of materials and constructions used to seal linear joints or construction joints in fire resistant separating elements it has been necessary to separate the extended application principles into gen
49、eric seal types. Permitted variations may be used alone or in combination, unless stated otherwise. Principles common to all generic seal types are given in Section 4.1. Principles and guidance relating to each specific generic joint type are given in Annex A to this document. Variables for each seal type, which require consideration, are included in this report. These are as follows: separating element; joint width/s