《08-30178375-DC.pdf》由会员分享，可在线阅读，更多相关《08-30178375-DC.pdf（16页珍藏版）》请在三一文库上搜索。
1、a Date: 26 November 2008 Origin: European Latest date for receipt of comments: 28 February 2009 Project no.: 2008/00642 Responsible committee: MTE/23 Woodworking machines Interested committees: Title: Draft BS EN 1218-2:2004/A1 Safety of woodworking machines - Tenoning machines Part 2: Double end te
2、noning and/or profiling machines fed by chain or chains Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN1218-2 : 2004 and partially supersede. NONE If you are aware of a current national standard which may be affected, please noti
3、fy the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 28 February 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication.
4、 No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing p
5、urposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from B
6、SI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be
7、found via the British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 700
8、1 Form 36 Version 8.0 DPC: 08/30178375 DC Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are wel
9、come and will assist in the preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obli
10、ged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to e
11、nsure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. C
12、omments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as gi
13、ven in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause
14、 No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to re
15、ad . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windo
16、ws is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM FINAL DRAFT EN 1218-2:2004 prA1 November 2008 ICS 79.120.10 English Version Safety of woodwor
17、king machines - Tenoning machines - Part 2: Double end tenoning and/or profiling machines fed by chain or chains Scurit des machines pour le travail du bois - Tenonneuses - Partie 2: Machines tenonner et/ou profiler chane ou chanes Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlit
18、zmaschinen - Teil 2: Doppelseitige Zapfenschneid- und Schlitzmaschinen und/oder Doppelendprofiler mit Kettenbandvorschub This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 142. This draft amendment A1, if approved,
19、 will modify the European Standard EN 1218-2:2004. If this draft becomes an amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. This draft amend
20、ment was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are
21、 the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer
22、land and United Kingdom. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITE
23、E FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1218-2:2004/prA1:2008: E Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45,
24、Uncontrolled Copy, (c) BSI EN 1218-2:2004/prA1:2008 (E) 2 Contents Page Foreword3 1 Modification to the Foreword .4 2 Modification to the Introduction.4 3 Modification to Clause 1, Scope.4 4 Modification to Clause 2, Normative references 4 5 Modification to 3.3, Definitions.5 6 Modification to Claus
25、e 4, List of hazards6 7 Modification to 5.2.1, Safety and reliability of control systems7 8 Modification to 5.2.3, Starting.8 9 Modification to 5.2.4.1, Normal stopping 8 10 Modification to 5.2.4.2, All other stop controls.8 11 Modification to 5.2.5, Emergency stop8 12 Modification to 5.2.8, Speed c
26、hanging 8 13 Modification to 5.2.10, Failure of the power supply.8 14 Modification to 5.2.11, Failure of the control circuits 8 15 Modification to 5.3.2, Risk of break-up during operation8 16 Modification to 5.3.3.2, Strength 8 17 Modification to 5.3.3.6, Spindle rings 9 18 Modification to 5.3.7.3.3
27、 c)9 19 Modification to 5.3.7.3.4 c)9 20 Modification to 5.4.1, Fire9 21 Modification to 5.4.4, Electricity.9 22 Modification to 5.4.5, Ergonomics and handling9 23 Modification to 5.4.6, Lighting10 24 Modification to 5.4.9, Radiation10 25 Modification to 5.4.12, Isolation .10 26 Modification to 5.4.
28、13, Maintenance 10 27 Modification to 6.2, Marking .11 28 Modification to 6.3, Instruction handbook 11 29 Modification to Annex A12 30 Modification to Annex C12 31 Modification to Annex ZA .12 32 Addition of Annex ZB13 33 Modification to Bibliography13 Licensed Copy: London South Bank University, So
29、uth Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EN 1218-2:2004/prA1:2008 (E) 3 Foreword This document (EN 1218-2:2004/prA1:2008) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI. This document is currently
30、submitted to the Unique Acceptance Procedure. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the Machinery Directive. For relationship with EU Directive, see informative Annexes Z
31、A and ZB, which are integral parts of this document. This document includes Amendment A.1, approved by CEN on XXXX-XX-XX. The main changes compared to the previous version are: - Addition of Annex ZB - Editorial modification of Annex ZA - “Minor” changes of sub-clauses 1, 2, 3.3, 4, 5.2.1, 5.2.3, 5.
32、2.4.1, 5.2.4.2, 5.2.5, 5.2.8, 5.2.10, 5.2.11, 5.3.2, 5.3.3.2, 5.3.3.6, 5.4.1, 5.4.4, 5.4.6, 5.4.9, 5.4.12, 5.4.13, 6.2, 6.3, Annex A, Annex C, Bibliography - Technical changes of sub-clauses 5.4.5 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy
33、, (c) BSI EN 1218-2:2004/prA1:2008 (E) 4 1 Modification to the Foreword Replace the fourth paragraph with the following: “For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.“ 2 Modification to the Introduction Replace “EN 1070:1998“ wi
34、th “EN ISO 12100-1:2003“. 3 Modification to Clause 1, Scope Replace the 1st paragraph with: “This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to double end tenoning and/or profiling machines fed by chain or chains, hereinafter
35、 referred to as the machine, designed to cut solid wood, chipboard, fibreboard or plywood and also these materials where they are covered with plastic laminate or edgings. The workpiece is fed passed the tools by an integrated feed.“ Delete the 2nd paragraph. 4 Modification to Clause 2, Normative re
36、ferences Delete reference to EN 294:1992. Replace reference to EN 418:1992 with: “EN ISO 13850:2008, Safety of machinery Emergency stop Principles for design (ISO 13850:2006)“ and replace “EN 418:1992“ in 5.2.5, 1st paragraph, with “EN ISO 13850:2008“. Replace “EN 847-1:1997, Tools for woodworking -
37、 Safety requirements Part 1: Milling tools and circular saw blades“ with “EN 847-1:2005, Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades“ in Introduction, Clause 2 and throughout the document. Replace “EN 954:1996“ with “EN ISO 13849-1:2008 Safety of machiner
38、y - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2006)“ throughout the document. Replace “EN 60204-1:1992“ with “EN 60204-1:2006“ and replace in the title “(IEC 60204-1:1992, modified)“ with “(IEC 60204-1:2005, modified)“. Replace “EN 60947-4-1:1992“ w
39、ith “EN 60947-4-1:2001“ throughout the document and replace in the title “(IEC 60947-4-1:1990)“ with “(IEC 60947-4-1:2000)“. Replace “EN 60947-5-1:1997“ with “EN 60947-5-1:2004“ throughout the document and replace in the title “(IEC 60947-5-1:1997)“ with “(IEC 60947-5-1:2003)“. Replace “CEN/TS 61496
40、-2:2003“ with “CLC/TS 61496-2:2006“ in Clause 2 and throughout the document and the 3rd element of the title with “Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)“. Licensed Copy: London South Bank University, South Bank Univer
41、sity, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EN 1218-2:2004/prA1:2008 (E) 5 Replace reference to “HD 21.1 S3:1997“ with “HD 21.1 S4:2002, Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation Part 1: General requirements“ and replace “HD 21.1 S3:1997“ with
42、“HD 21.1 S4:2002“ throughout the document. Replace reference to “HD 22.1 S3:1997“ with “HD 22.1 S4:2002, Cables of rated voltages up to and including 450/750 V and having cross-linked insulation Part 1: General requirements“ and replace “HD 22.1 S3:1997“ with “HD 22.1 S4:2002“ throughout the documen
43、t. Delete reference to EN 1070:1998 Add the following references: “EN 614-1:2006, Safety of machinery Ergonomic design principles Part 1: Terminology and general principles“, “EN 894-1:1997, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General
44、principles for human interactions with displays and control actuators EN 894-2:1997, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays EN 894-3:2000, Safety of machinery Ergonomics requirements for the design of displays and control actuato
45、rs Part 3: Control actuators“, “EN 1005-1:2001, Safety of machinery Human physical performance Part 1: Terms and definitions EN 1005-2:2003, Safety of machinery Human physical performance Part 2: Manual handling of machinery and component parts of machinery EN 1005-3:2002, Safety of machinery Human
46、physical performance Part 3: Recommended force limits for machinery operation EN 1005-4:2005, Safety of machinery Human physical performance Part 4: Evaluation of working postures and movements in relation to machinery“ “EN 50370-1:2005, Electromagnetic compatibility (EMC) Product family standard fo
47、r machine-tools Part 1: Emission EN 50370-2:2003, Electromagnetic compatibility (EMC) Product family standard for machine-tools Part 2: Immunity“, “EN 60439-1:1999, Low-voltage switchgear and controlgear assemblies Part 1: Type-tested and partially type-tested assemblies (IEC 60439-1:1999)“, “EN 613
48、10-1:2008, Safety of machinery Indication, marking and actuation Part 1: Requirements for visual, acoustic and tactile signals (IEC 61310-1:2007)“ 5 Modification to 3.3, Definitions In 3.1 replace “EN 1070:1998“ with “EN ISO 12100-1:2003“. In 3.3.12, replace the term with “displaceable machine“. In
49、3.3.13, replace the term with “information from the supplier“. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EN 1218-2:2004/prA1:2008 (E) 6 6 Modification to Clause 4, List of hazards Replace the heading of Clause 4 with: “List of significant hazards”. Replace the clause content with: “This claus