《08-30179725-DC.pdf》由会员分享，可在线阅读，更多相关《08-30179725-DC.pdf（6页珍藏版）》请在三一文库上搜索。
1、Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30179725 DC Date: 28 October 2008 Origin: European Latest date for receipt of comments: 31 December 2008 Project no.: 2008/00965 Responsible com
2、mittee: MRE/1 Mining mechanical equipment and machinery Interested committees: Title: Draft BS EN 1889-2:2003/A1 Machines for underground mines - Mobile machines working underground Safety - Part 2: Rail locomotives Supersession information: If this document is published as a standard, the UK implem
3、entation of it will supersede BSEN1889-2 : 2003 and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT
4、 CURRENT BEYOND 31 December 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior wri
5、tten permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of th
6、is draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the
7、responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Commit
8、tee Service Centre (BSI) E-mail: a Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and
9、 will assist in the preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to p
10、ublish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure th
11、at all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments
12、should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in t
13、he example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Su
14、bclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so
15、that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a
16、trademark of Microsoft Corporation. b Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM FINAL DRAFT EN 1889-2:2003 prA1 October 2008 ICS 73.100.40 English Version Machines for underground
17、 mines - Mobile machines working underground - Safety - Part 2: Rail locomotives Machines pour lexploitation de mines souterraines - Machines mobile souterraines - Scurit - Partie 2: Locomotives sur rails Maschinen fr den Bergbau unter Tage - Bewegliche Maschinen fr die Verwendung unter Tage - Siche
18、rheit - Teil 2: Lokomotiven This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 196. This draft amendment A1, if approved, will modify the European Standard EN 1889-2:2003. If this draft becomes an amendment, CEN me
19、mbers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. This draft amendment was established by CEN in three official versions (English, French, German). A version i
20、n any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark
21、, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Warning : This document is not a European Standard. It is distribute
22、d for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exp
23、loitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1889-2:2003/prA1:2008: E Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI EN 1889-2:2003/prA1:2008 (E) 2 Foreword This document (EN 1889-2:2
24、003/prA1:2008) has been prepared by Technical Committee CEN/TC 196 “Machines for underground mines - Safety”, the secretariat of which is held by DIN. This document is currently submitted to the Unique Acceptance Procedure. This document has been prepared under a mandate given to CEN by the European
25、 Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document. Licensed Copy: London South Bank University, South Bank University, 16/11/
26、2008 12:05, Uncontrolled Copy, (c) BSI EN 1889-2:2003/prA1:2008 (E) 3 1 Modification to 7.2.1 Marking Replace the text of the 1st indent with the following: “the business name and full address of the manufacturer and, where applicable, his authorised representative;“ Replace the text of the 2nd inde
27、nt with the following: “designation of the machinery;“. 2 Modification to Annex ZA Replace the existing Annex ZA with the following: “ Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EG This European Standard has been prepared u
28、nder a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 98/37/EG, amended by 98/79/EG on machinery. Once this standard is cited in the Official Journal of the European Comm
29、unities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements except ESR
30、1.5.8 and 1.7.4 f) of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.“ Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled
31、Copy, (c) BSI EN 1889-2:2003/prA1:2008 (E) 4 3 Addition of Annex ZB Add the following Annex ZB: “ Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the
32、European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of the European Communities under that Directive and has been implemented
33、as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements except ESR 1.5.8 and 1.7.4.2 u) of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.“ Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:05, Uncontrolled Copy, (c) BSI