《08-30189974-DC.pdf》由会员分享，可在线阅读，更多相关《08-30189974-DC.pdf（25页珍藏版）》请在三一文库上搜索。
1、a Date: 4 December 2008 Origin: European Latest date for receipt of comments: 13 March 2009 Project no.: 2008/02993 Responsible committee: PRI/82 Thermoplastic materials Interested committees: Title: Draft BS EN 13245-1 Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building appl
2、ications Part 1: Designation of PVC-U profiles Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN13245-1 : 2004 and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the s
3、ecretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 13 March 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowl
4、edgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. El
5、ectronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer
6、 Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via t
7、he British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 V
8、ersion 8.0 DPC: 08/30189974 DC Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:08, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and wi
9、ll assist in the preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to publ
10、ish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that
11、all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments sho
12、uld be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the
13、example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subcl
14、ause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so tha
15、t the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a tra
16、demark of Microsoft Corporation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:08, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM DRAFT prEN 13245-1 November 2008 ICS 83.140.99Will supersede EN 13245-1:2004 English Version Plastics -
17、Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles Plastiques - Profils en poly(chlorure de vinyle) non plastifi (PVC-U) pour applications dans le btiment - Partie 1: Dsignation des profils en PVC-U Kunststoffe - Profile aus weichmac
18、herfreiem Poly(vinylchlorid) (PVC-U) fr die Anwendung im Bauwesen - Teil 1: Bezeichnung von PVC-U Profilen This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 249. If this draft becomes a European Standard, CEN members are boun
19、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This draft European Standard was established by CEN in three official versions (English, French, German). A version in any
20、other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Esto
21、nia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Recipients of this draft are invited to submit, with their comments, notif
22、ication of any relevant patent rights of which they are aware and to provide supporting documentation. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN C
23、OMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. prEN 13245-1:2008: E Licensed Copy:
24、London South Bank University, South Bank University, 31/01/2009 04:08, Uncontrolled Copy, (c) BSI prEN 13245-1:2008 (E) 2 Contents Page Foreword4 1 Scope 5 2 Normative references5 3 Terms and definitions .6 4 Designation of PVC-U profiles7 5 Codification system for Data block 3 to Data block 58 5.1
25、Vicat softening temperature (Data block 3) 8 5.2 Modulus of elasticity in flexure (Data block 3) .8 5.3 Nominal linear mass (Data block 4).8 5.4 Heat reversion at 100 C (Data block 4).9 5.5 Impact resistance (Data block 4)9 5.6 Durability (Data block 5)9 5.6.1 General9 5.6.2 Test methods for ageing.
26、10 5.6.3 Methods for assessing of ageing.11 5.6.4 Codification for properties after ageing11 6 Required characteristics for Type 3 and Type 4 profiles 13 6.1 Resistance to cross cut (only for Type 4 profiles) 13 6.2 Thermal resistance (only for Type 3 and Type 4 profiles).13 6.3 Water vapour resista
27、nce (only for Type 3 and Type 4 profiles, intended to be used for inside building applications) .13 6.4 Peel strength (only for Type 3 profiles)13 7 Optional characteristics13 7.1 Resistance to staining.13 7.2 Appearance and finishing of the coating (for Type 3 and Type 4 profiles, only)14 7.2.1 Gen
28、eral14 7.2.2 Single colour profiles14 7.2.3 Non-uniform colour and texture profiles.14 7.2.4 Gloss.14 8 Example of the designation of a PVC-U profile 14 9 Use of reprocessable and recyclable material .15 Annex A (normative) Determination of the linear mass16 A.1 Apparatus16 A.2 Test specimens16 A.3
29、Procedure .16 A.4 Calculation and expression of results.16 Annex B (normative) Determination of the impact resistance .17 B.1 Principle17 B.2 Apparatus .17 B.3 Test specimens17 B.4 Conditioning.18 B.4.1 Impact resistance at 23 C18 B.4.2 Impact resistance at low temperature .18 B.5 Procedure .18 B.6
30、Expression of results 19 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:08, Uncontrolled Copy, (c) BSI prEN 13245-1:2008 (E) 3 Annex C (normative) Determination of peel strength .20 C.1 Principle20 C.2 Apparatus.20 C.3 Preparation of test pieces.20 C.4 Conditioning
31、 21 C.5 Procedure.21 C.5.1 Constant-speed tensile test21 C.5.2 Constant-load tensile test.21 C.6 Test report22 Bibliography23 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:08, Uncontrolled Copy, (c) BSI prEN 13245-1:2008 (E) 4 Foreword This document (prEN 13245-1:
32、2008) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This document is currently submitted to the CEN Enquiry. This document will supersede EN 13245-1:2004. EN 13245 consists of the following parts, under the general title Plastics Unplasticiz
33、ed poly(vinyl chloride) (PVC-U) profiles for building applications: Part 1: Designation of PVC-U profiles (merging of EN 13245-1:2004 and wi 00249601) Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes Part 3: Designation of PVC-UE profiles (merging of wi
34、00249602 and wi 00249603) It is a revision of EN 13245-1:2004 with the extension of the scope to: light coloured PVC-U profiles with a laminated foil or a lacquered-coating; coloured PVC-U profiles, obtained by a mono-extrusion or a co-extrusion process, with laminated foil or with lacquered-coating
35、. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:08, Uncontrolled Copy, (c) BSI prEN 13245-1:2008 (E) 5 1 Scope This part of EN 13245 establishes a system of designation for profiles made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for buildin
36、g applications. This part is applicable to light coloured and coloured PVC-U profiles, obtained by a mono-extrusion or a co- extrusion process, with a laminated foil or with a lacquered-coating. It specifies test methods and test parameters. This method of designation is intended to be used in produ
37、ct specification when the application is specified. NOTE It is recommended to use this method for the designation of PVC-U profiles for information related to technical literature of the manufacturer, not for the marking of the products. Profiles for the management of electrical power cables, commun
38、ication cables and power track systems used for the distribution of electrical power and profiles for windows or doors are not covered by this European Standard. 1) 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references,
39、 only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 438-2:2005, High-pressure decorative laminates (HPL) Sheets based on thermosetting resins (Usually called Laminates) Part 2: Determination of properties EN 47
40、7:1995, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors Determination of the resistance to impact of main profiles by falling mass EN 478:1995, Unplasticized poly(chloride) (PVC-U) profiles for the fabrication of windows and doors Appearance after exposure a
41、t 150 C Test method EN 479, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors Determination of heat reversion EN 513:1999, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors Determination of the resistance to artificial w
42、eathering EN 12720, Furniture Assessment of surface resistance to cold liquids EN 13245-2, Plastics Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications Part 2: PVC-U profiles and PVCUE profiles for internal and external wall and ceiling finishes EN 20105-A02, Textiles Tests
43、 for colour fastness Part A02: Grey scale for assessing change in colour (ISO 105-A02:1993) EN ISO 105-A01, Textiles Tests for colour fastness Part A01: General principles of testing (ISO 105- A01:1994) 1) Profiles that are excluded are in the scopes of standards prepared by CEN/TC 33 or CENELEC/TC
44、213. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:08, Uncontrolled Copy, (c) BSI prEN 13245-1:2008 (E) 6 EN ISO 178, Plastics Determination of flexural properties (ISO 178:2001) EN ISO 306:1996, Plastics Thermoplastics materials Determination of Vicat softening t
45、emperature (VST) (ISO 306:1994) EN ISO 472, Plastics Vocabulary (ISO 472:2001) EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1403-1:2001) EN ISO 1163-2, Plastics Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion ma
46、terials Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995) EN ISO 2409, Paints and varnishes Cross-cut test (ISO 2409:1992) EN ISO 2813, Paints and varnishes Determination of specular gloss of non-metallic paint films at 20 degrees, 60 degrees and 85 degrees (ISO
47、 2813:1994) EN ISO 4624:2003, Paints and varnishes Pull-off test for adhesion (ISO 4624:2002) EN ISO 4892-2:1999, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc sources (ISO 4892-2:1994) EN ISO 8256:2004, Plastics Determination of tensile-impact strength (ISO 8256:2004) I
48、SO 7724-1, Paints and varnishes Colorimetry Part 1: Principles ISO 7724-2, Paints and varnishes Colorimetry Part 2: Colour measurement ISO 7724-3, Paints and varnishes Colorimetry Part 3: Calculation of colour differences 3 Terms and definitions For the purposes of this document, the terms and defin
49、itions given in EN ISO 472 and EN ISO 1043-1, and the following apply. 3.1 PVC-U profile profile made of unplasticized poly(vinyl chloride) (PVC-U) material NOTE It applies to profiles made of non-cellular material as opposed to cellular material. 3.2 Type of profile 3.2.1 Type 1 profile PVC-U profile obtained by a mono-extrusion process (coloured in th