《09-30192939-DC.pdf》由会员分享，可在线阅读，更多相关《09-30192939-DC.pdf（12页珍藏版）》请在三一文库上搜索。
1、a Date: 20 January 2009 Origin: International Latest date for receipt of comments: 30 April 2009 Project no.: 2008/03761 Responsible committee: GEL/20/17 Low voltage cables Interested committees: Title: Draft BS EN 60811-100 Electric and optical fibre cables - Test methods for non-metallic materials
2、 - Part 100: General Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNIN
3、G: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 April 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See over
4、leaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to disse
5、mination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-operati
6、ng organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on t
7、he BSI web site http:/. Direct tel: 0208 996 7281 Responsible Committee Secretary: Mr S Bounds (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 09/30192939 DC Licensed Copy: London
8、South Bank University, South Bank University, 02/02/2009 05:40, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent s
9、tandard. There is a high probability that this text could be adopted by CENELEC as a reference document for harmonization or as a European Standard. Recipients of this draft are requested to comment on the text bearing in mind this possibility. UK Vote Please indicate whether you consider the UK sho
10、uld submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must b
11、e submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not su
12、bmitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/
13、Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secreta
14、riat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encou
15、ntered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, South Bank University, 02/02/2009 05:40, Uncontrolled Copy, (c) BSI FORM CD (IEC) 2008-08-
16、01 20/1010/CD COMMITTEE DRAFT (CD) IEC/TC or SC: TC 20 Project number IEC 60811-100 Ed. 1.0 Title of TC/SC: Electric cables Date of circulation 2009-01-16 Closing date for comments 2009-03-20* Also of interest to the following committees SC 18A, TC 46, SC 46A, SC 46C, SC 86A Supersedes document 20/9
17、98/MCR Proposed horizontal standard Other TC/SCs are requested to indicate their interest, if any, in this CD to the TC/SC secretary Functions concerned: Safety EMC Environment Quality assurance Secretary: H Myland (DE) THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT SHOULD NOT BE USED
18、FOR REFERENCE PURPOSES. RECIPIENTS OF THIS DOCUMENT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. Title: IEC 60811-100 Ed. 1.0: Electric and optical fibre cables Test methods for non-metallic ma
19、terials - Part 100: General (Titre) : Introductory note This CD has been developed by WG 17 of TC 20. It is circulated in accordance with the decision of TC 20 at its meeting in Rome on 16/17 October 2008 (20/1000/RM minute 9.1) Note that, in conjunction with advice from Central Office, the original
20、 (provisional) title has been improved. *NOTE: In accordance with SMB decision 133/16 (Sao Paulo, 2008) the secretary of IEC TC 2O has requested a period for comments of two months for this particular CD. Copyright 2009 International Electrotechnical Commission, IEC. All rights reserved. It is permi
21、tted to download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions. You may not copy or “mirror“ the file or printed version of the document, or any part of it, for any other purpose without permission in writing from IEC
22、. Licensed Copy: London South Bank University, South Bank University, 02/02/2009 05:40, Uncontrolled Copy, (c) BSI 60811-100 Ed 1.0/CD IEC 2 20/1010/CD CONTENTS FOREWORD.2 1 Scope.5 2 Normative references .5 3 Terms and definitions .5 4 Test values.5 5 Applicability6 6 Type tests and other tests 6 7
23、 Test report6 Annex A (informative) Structure and content of IEC 60811.7 Licensed Copy: London South Bank University, South Bank University, 02/02/2009 05:40, Uncontrolled Copy, (c) BSI 60811-100 Ed 1.0/CD IEC 3 20/1010/CD INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRIC AND OPTICAL FIBRE CABLES
24、 TEST METHODS FOR NON-METALLIC MATERIALS Part 100: General FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-o
25、peration on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to
26、 as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this
27、preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
28、consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable effo
29、rts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publicati
30、ons transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and
31、cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts an
32、d members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publica
33、tion or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publica
34、tion may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60811-100 has been prepared by IEC technical committee 20: Electric cables. It does not cancel or replace a specific part or clause in the existing se
35、ries IEC 60811-1-1 to IEC 60811-5-1 inclusive, but it collects together the general matters that apply to each of the replacement parts. Full details of the replacements are shown in Annexes A and B. This revised series of IEC 60811 is based upon the principle of “one test one part” in addition, one
36、 significant technical change is made throughout with respect to the existing series of document, as follows: - A defined minimum scheme for the presentation of test reports is introduced. Licensed Copy: London South Bank University, South Bank University, 02/02/2009 05:40, Uncontrolled Copy, (c) BS
37、I 60811-100 Ed 1.0/CD IEC 4 20/1010/CD The text of this standard is based on the following documents: FDIS Report on voting XX/XX/FDIS XX/XX/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has be
38、en drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date1) indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this
39、 date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 1) The National Committees are requested to note that for this publication the maintenance result date is Licensed Copy: London South Bank University, South Bank University, 02/02/2009 05:40, Uncontroll
40、ed Copy, (c) BSI 60811-100 Ed 1.0/CD IEC 5 20/1010/CD ELECTRIC AND OPTICAL FIBRE CABLES TEST METHODS FOR NON-METALLIC MATERIALS Part 100: General 1 Scope IEC 60811 (series) specifies the test methods to be used for testing non-metallic materials of electric and optical fibre cables for energy, commu
41、nication and control applications, including cables for ships and offshore applications. These test methods are intended to be referenced in standards for cable construction and for cable materials. Note: The non-metallic materials are typically used for insulating, sheathing, bedding, filling or ta
42、ping within cables. This part 100 describes general requirements and considerations that are applicable to all the test methods given in the particular parts, unless otherwise specified. Each test method is contained in a separately numbered part of the standard. These respective parts are identifie
43、d in Table A.1 of Annex A. The corresponding clauses in the previous edition of this standard are supplied for reference. Table A.2 of Annex A lists the clauses of the previous edition, to facilitate location of the corresponding part in the current edition. 2 Normative references The following refe
44、renced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies IEC 60050-461, International Electrotechnical Vocabulary. Part 461:
45、Electric Cables. 3 Terms and definitions For the purposes of this document, the definitions in IEC 60050-461 apply, together with the following: 3.1 median value when several test results have been obtained and ordered in an increasing (or decreasing) succession, the median value is the middle value
46、 if the number of available values is odd, and the mean of the two middle values if the number is even 4 Test values Full test conditions (such as temperatures, durations, etc.) and full test requirements are not specified in the particular parts of IEC 60811. It is intended that they should be spec
47、ified by the standard dealing with the relevant type of cable. Any test requirements which are given in the particular parts of IEC 60811 may be modified by the relevant cable standard to suit the needs of a particular type of cable. Licensed Copy: London South Bank University, South Bank University
48、, 02/02/2009 05:40, Uncontrolled Copy, (c) BSI 60811-100 Ed 1.0/CD IEC 6 20/1010/CD 5 Applicability Conditioning values and testing parameters are specified where appropriate for the most common types of insulating and sheathing compounds and of cables, wires and cords. 6 Type tests and other tests
49、The test methods described in the particular parts of IEC 60811 are primarily intended to be used for type tests. In certain tests, where there are essential differences between the conditions for type tests and those for more frequent tests, such as routine tests, these differences are indicated. 7 Test report The test report shall contain the following