《06-30148192-DC.pdf》由会员分享，可在线阅读，更多相关《06-30148192-DC.pdf（24页珍藏版）》请在三一文库上搜索。
1、a Date: 15 December 2006 Origin: International Latest date for receipt of comments: 31 March 2007 Project no.: 2006/00869 Responsible committee: EPL/46/2 Radio frequency connectors and waveguides Interested committees: Title: Draft BS EN 61169-4:2007 Radio-frequency connectors - Part 4: R.F. coaxial
2、 connectors with inner diameter of outer conductor 1 6 mm (0.63 in) with screw lock - Characteristic impedance 50 ohms (Type 7-16) Supersession information: If this document is published as a standard, the UK implementation of it will supersede DD IEC/PAS 61169-4:2006 and partially supersede NONE .
3、If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 March 2007. This draft is issued to allow comments from int
4、erested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Pat
5、ent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or
6、 email ordersbsi-. British, International and foreign standards are also available from BSI Customer Services. British Standards on CD or Online are available from British Standards Publishing Sales Limited. Tel: 01344 404409 or email bsonlinetechindex.co.uk. Information on the co-operating organiza
7、tions represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web
8、site http:/www.bsi-. Direct tel: 0208 996 7281 Responsible Committee Secretary: Mr S Bounds (BSI) E-mail: simon.boundsbsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 6.1 DPC: 06/30148192 DC Licensed
9、Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist
10、in the preparation of the consequent standard. If no comments are received to the contrary, then the UK will approve this draft. There is a high probability that this text could be adopted by CENELEC as a reference document for harmonization or as a European Standard. Recipients of this draft are re
11、quested to comment on the text bearing in mind this possibility. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate a
12、ttention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97
13、 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting
14、 comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at:http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Fig
15、ure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connect
16、ion . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed
17、 Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI FORM CDV (IEC) 2005-09-23 46F/60/CDV COMMITTEE DRAFT FOR VOTE (CDV) PROJET DE COMIT POUR VOTE (CDV) Project number IEC 61169-4 Ed: 1.0 Numro de projet IEC/TC or SC: SC46F
18、 CEI/CE ou SC: Secretariat / Secrtariat France Submitted for parallel voting in CENELEC Soumis au vote parallle au CENELEC Date of circulation Date de diffusion 2006-12-15 Closing date for voting (Voting mandatory for P-members) Date de clture du vote (Vote obligatoire pour les membres (P) 2007-05-1
19、8 Also of interest to the following committees Intresse galement les comits suivants Supersedes document Remplace le document 46F/40/NP any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organiza
20、tions liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matt
21、ers express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC Nationa
22、l Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC
23、 National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provid
24、es no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employee
25、s, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the pu
26、blication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the poss
27、ibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC XXX has been prepared by subcommittee XX: TITLE, of IEC technical committee XX: The text of this
28、standard is based on the following documents: FDIS Report on voting XX/XX/FDIS XX/XX/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Pa
29、rt 2. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 61169-4/Ed.1 CDV IEC:200X 4 The committee has decided that the contents of this publication will remain unchanged until the maintenance result date1) indica
30、ted on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 1) The National Committees are requested to note that for this publication the maintenance r
31、esult date is . 2011. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 61169-4/Ed.1 CDV IEC:200X 5 IEC 61169 Radio-frequency connectors Part 4: R.F. coaxial connectors with inner diameter of outer conductor 16 m
32、m (0.63 in) with screw lock Characteristic impedance 50 ohms (Type 7-16) 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type 7-16 R.F. coaxial connectors with screw lock. The connectors are
33、 normally used with 50 flexible and semi-rigid R.F. cables for middle power applications in an operating frequency range up to 7,5 GHz. It describes the interface dimensions for general purpose grade 2 connectors, dimensional details for standard test connectors, grade 0, together with gauging infor
34、mation and the mandatory tests selected from QC 22000(IEC61169-1), applicable to all DS relating to type 7- 16 connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers test schedules and inspection requirements. 2 Normative re
35、ferences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61169-1 Radio-frequency connectors P
36、art 1: Generic specification General requirements and measuring methods IEC 62037 RF connectors, connector cable assemblies, and cables - Intermodulation level measurement 3 Mating face and gauge information Metric dimension are original dimensions. All undimensioned pictorial configurations are for
37、 reference purpose only. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 61169-4/Ed.1 CDV IEC:200X 6 3.1 Dimensions-General connectors -Grade 2 3.1.1 Connector with pin centre contact Fig 1. Connector with pin
38、centre contact (for dimensions see table Table 1) Table 1 Connector with pin centre contact. Ref. mm in notes min max min max a M291,5 M291,5 2 b 20,6 21,4 0,811 0,843 c 18,03 18,21 0,7098 0,7169 d 4,96 5,04 0,1953 0,1984 e 15,85 16,25 0,6240 0,6398 f 7(nominal) 0,276(nominal) 1 g 1,4 1,6 0,0551 0,0
39、630 h 1,47 1,77 0,0579 0,0697 i 7,00 8,00 0,276 0,315 l - 4,5 - 0,177 m 7,00 9,00 0,276 0,354 Note 1：The tolerances on this dimension is determined by the tolerance of characteristic impedance. Note 2：M291,5 indicates metric screw thread with nominal diameter 29mm（）（）1,141in and pitch 1,5mm 0,059in
40、. Note 3：Mechanical and electrical reference plane. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 61169-4/Ed.1 CDV IEC:200X 7 3.1.2 Connector with socket centre contact Fig 2. Connector with socket centre con
41、tact (for dimensions see Table 2) Table 2 Connector with socket centre contact Ref. mm in Note min Max min max a M291,5 M291,5 3 e 15,85 16,25 0,6240 0,6398 f 7(nominal) 0,276(nominal) 1 k 10 - 0,394 - n 22,1 22,9 0,870 0,902 p 0,5 0,7 0,0197 0,0276 q 1,77 2,07 0,0697 0,0815 r 5 - 0,197 - s 8,1 - 0,
42、319 - t 17,84 18,02 0,7024 0,7094 2 Note 1: The tolerances on this dimensions is determined by the tolerance of characteristic impedance. Note 2: Standard is a non slotted outer contact. If a slotted outer contact is required, the slotting shall be bent outwards to 18,5 mm（）0,728in max. The slotted
43、sleeve shall meet the gauge retention force. Note 3: M291,5 indicates metric screw thread with nominal diameter 29mm （）（）1,141in and pitch 1,5mm 0.,59in . Note 4: Slot design optional. Contact to be closed to meet the gauge retention force. Note 5: Mechanical and electrical reference plane. Licensed
44、 Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 61169-4/Ed.1 CDV IEC:200X 8 3.2 Gauges for general purpose connectors - Grade 2 3.2.1 Gauges for connector with socket centre contact 3.2.1.1 Centre contact Fig 3. Gauge
45、pin for socket centre contact Test procedure a) A steel test pin ( Fig 3) with a diameter a of 0 01.,0 1 , 5 + mm ( 0 0004, 0 2008, 0 + in) and a 0,4m(16in) max finish shall be inserted once into the centre contact a minimum distance of 2mm (0,079in). b) A second steel test pin(Fig.3) with a diamete
46、r a of 0 01.,0 96, 4 + mm( 0 0004, 0 1953, 0 + in) and a 0,4m(16in) max finish shall have a minimum retention force of 6 N after insertion into the centre contact. It is recommended that this gauge should have a mass of 600g. 1.1.1 Outer contact Fig 4. Gauge ring for socket outer contact a) For non-
47、slotted outer contacts, a steel test ring ( Fig 4) with inner diameter a of 0 01. 0 03,18 mm ( 0 0004. 0 7098, 0 in) and a 0,4m(16in)max finish shall be pushed over the outer contact of connector. The force required to push this test ring on to the connector a minimum distance of 8mm(0,315in) shall
48、not exceed 40N. b) For slotted outer contacts, a steel test ring ( Fig 4) with inner diameter a of 02. 0 0 23,18 + mm( 0008. 0 0 7177, 0 + in) and a 0.4m(16in)max finish shall be placed over the outer contact of the connector. The test ring shall uniformly meet the outer contact when pushed no more
49、than 3mm (0,12in) over this contact. The retention force for the gauge ring shall be 15N min. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:21:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 61169-4/Ed.1 CDV IEC:200X 9 3.3 Dimensions standard test connectors Grade 0 In order to carry out the reflection coefficient mea