《08-30152069-DC.pdf》由会员分享，可在线阅读，更多相关《08-30152069-DC.pdf（16页珍藏版）》请在三一文库上搜索。
1、a Date: 17 September 2008 Origin: European Latest date for receipt of comments: 31 December 2008 Project no.: 2006/01683 Responsible committee: PRI/82 Thermoplastic materials Interested committees: Title: Draft BS EN ISO 1628-3 Plastics - Determination of the viscosity of polymers in dilute solution
2、 using capillary viscometers Part 3: Polyethylenes and polypropylenes Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSENISO1628-3 : 2003 and partially supersede. NONE If you are aware of a current national standard which may be affe
3、cted, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 December 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prio
4、r to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organizati
5、on for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also
6、 available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in t
7、his draft may be found via the British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax:
8、+44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30152069 DC Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome
9、and will assist in the preparation of the consequent British Standard. If no comments are received to the contrary, then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even i
10、f this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should s
11、ubmit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be sub
12、mitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitt
13、ed electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Templ
14、ate for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat
15、observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountere
16、d in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM
17、 DRAFT prEN ISO 1628-3 September 2008 ICS 83.080.20Will supersede EN ISO 1628-3:2003 English Version Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes (ISO/DIS 1628-3:2008) Plastiques - Dtermination de la v
18、iscosit des polymres en solution dilue laide de viscosimtres capillaires - Partie 3: Polythylnes et polypropylnes (ISO/DIS 1628- 3:2008) Kunststoffe - Bestimmung der Viskositt von Polymeren in verdnnter Lsung durch ein Kapillarviskosimeter - Teil 3: Polyethylen und Polypropylen (ISO/DIS 1628-3:2008)
19、 This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 249. If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t
20、his European Standard the status of a national standard without any alteration. This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language
21、 and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem
22、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documenta
23、tion. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Manage
24、ment Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. prEN ISO 1628-3:2008: E Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI prEN ISO 1628-3:20
25、08 (E) 2 Contents Page Foreword3 Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI prEN ISO 1628-3:2008 (E) 3 Foreword This document (prEN ISO 1628-3:2008) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee
26、 CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This document is currently submitted to the parallel Enquiry. This document will supersede EN ISO 1628-3:2003. Endorsement notice The text of ISO/DIS 1628-3:2008 has been approved by CEN as a prEN ISO 1628-3:2008 without any modificati
27、on. Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUAT
28、ION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. RECIPIENTS OF THIS DRAFT ARE INVITED TO
29、 SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL STANDARD ISO/DIS 1628-3 International Organization for Standardization, 2008 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTER
30、NATIONALE DE NORMALISATION ISO/TC 61/SC 9 Voting begins on: 2008-09-11 Secretariat: ANSI Voting terminates on: 2009-02-11 Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 3: Polyethylenes and polypropylenes Plastiques Dtermination de la viscosit
31、 des polymres en solution dilue laide de viscosimtres capillaires Partie 3: Polythylnes et polypropylnes Revision of second edition (ISO 1628-3:2001) ICS 83.080.20 ISO/CEN PARALLEL ENQUIRY The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject of interest
32、to European standardization. In accordance with the ISO-lead mode of collaboration as defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a final draft, established on th
33、e basis of comments received, will be submitted to a parallel two-month FDIS vote in ISO and formal vote in CEN. In accordance with the provisions of Council Resolution 15/1993 this document is circulated in the English language only. Conformment aux dispositions de la Rsolution du Conseil 15/1993,
34、ce document est distribu en version anglaise seulement. To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent docu
35、ment est distribu tel quil est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI ISO/DIS 1628-3 ii ISO 2008 A
36、ll rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In down
37、loading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the
38、 General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address
39、given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in an
40、y form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale
41、 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI
42、 ISODIS 1628-3:2008(E) ISO 2008 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees
43、. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Intern
44、ational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part3. Draft International Standards adopted by the technical committees are circulated to the member bodies
45、 for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO1628 may be the subject of patent rights. ISO shall not be held responsible for identifying
46、any or all such patent rights. International Standard ISO1628-3 was prepared by Technical Committee ISO/TC61, Plastics, Subcommittee SC9, Thermoplastic materials. This third edition cancels and replaces the second edition (ISO1628-3:2001), of which it constitutes a minor revision (the third confirms
47、 Ubbelohde viscometers type in 5.1, and in 7.4.2 the solution method is modified ). ISO1628 consists of the following parts, under the general title Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers: Par1: General principles Part2: Poly(vinyl chloride
48、) resins Part3: Polyethylenes and polypropylenes Part4: Polycarbonate (PC) moulding and extrusion materials Part5: Thermoplastic polyester (TP) homopolymers and copolymers Part6: Methyl methacrylate polymers Licensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI L
49、icensed CopyChinese University of Hong Kong, 21/10/2008 04:22, Uncontrolled Copy, (c) BSI 1 Scope This part of ISO1628 defines particular conditions for determining the reduced viscosity (also known as viscosity number) and intrinsic viscosity of polyethylenes and polypropylenes at 135C in dilute solution. It is applicable