《08-30176534-DC.pdf》由会员分享，可在线阅读，更多相关《08-30176534-DC.pdf（10页珍藏版）》请在三一文库上搜索。
1、a Date: 29 July 2008 Origin: European Latest date for receipt of comments: 31 October 2008 Project no.: 2008/00223 Responsible committee: TCI/77 Ropes and cordage and fishing nets Interested committees: Title: Draft BS EN ISO 10547: Polyester fibre ropes - Double braid construction Supersession info
2、rmation: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REG
3、ARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 October 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting.
4、No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an or
5、ganization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the
6、committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/. Direct tel:
7、020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30176534 DC Licensed CopyChinese University of Hong Kong,
8、 21/10/2008 08:04, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent British Standard. If no comments are received to th
9、e contrary, then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK
10、will be obliged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is i
11、ntended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the fr
12、ont cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be pre
13、sented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (
14、7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying.
15、 Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademark
16、s, and Windows is a trademark of Microsoft Corporation. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD U
17、NTIL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL
18、REGULATIONS. RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL STANDARD ISO/DIS 10547 International Organization for Standardization, 2008 INTERNATIONAL
19、ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 38 Voting begins on: 2008-07-24 Secretariat: SAC Voting terminates on: 2008-12-24 Polyester fibre ropes Double braid construction Cordages en fibres de polyester Cordages coaxiaux ICS 59.080.50 ISO/CEN PARALLEL ENQU
20、IRY The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject of interest to European standardization. In accordance with the ISO-lead mode of collaboration as defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN members a
21、s would a CEN enquiry on a draft European Standard. Should this draft be accepted, a final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS vote in ISO and formal vote in CEN. In accordance with the provisions of Council Resolution 15/1993 this doc
22、ument is circulated in the English language only. Conformment aux dispositions de la Rsolution du Conseil 15/1993, ce document est distribu en version anglaise seulement. To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of
23、 editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent document est distribu tel quil est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Lice
24、nsed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10547 ii ISO 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unl
25、ess the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademar
26、k of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. I
27、n the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, n
28、either this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to eith
29、er ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Viola
30、tors may be prosecuted. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10547 ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions.1 4 Designation1 5 General requirements .2 5.1 Construc
31、tion 2 5.2 Number of strands.2 5.3 Manufacture and labelling2 5.4 Strand interchange2 6 Physical properties .3 7 Marking.4 7.1 Polyester double braided ropes.4 7.2 Polyester higher strength double braided ropes.4 Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c)
32、BSI ISO/DIS 10547 iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each
33、 member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internationa
34、l Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards
35、 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of
36、 patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10547 was prepared by Technical Committee ISO/TC 38, textiles, Subcommittee SC , . This second/third/. edition cancels and replaces the first/second/. edition (), clause(s) / subclause(s) / table(s)
37、/ figure(s) / annex(es) of which has / have been technically revised. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI DRAFT INTERNATIONAL STANDARD ISO/DIS 10547 ISO 2008 All rights reserved 1 Polyester fibre ropes Double braid construction 1 Scope This docu
38、ment specifies requirements for double braided ropes and for higher strength double braided ropes made of polyester and gives rules for their designation. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the
39、edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1968, Fibre ropes and cordage Vocabulary. ISO 2307, Fibre ropes Determination of certain physical and mechanical properties. ISO 9554, Fibre ropes General specificatio
40、ns. 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1968 apply. 4 Designation Fibre ropes shall be designated by the words “fibre rope“; number of this document; reference number of the rope; material from which the rope is made; level of strength of
41、 rope: double braided rope or high strength (hs) double braided rope. EXAMPLE 1 Designation of a double braided rope, reference number 20, corresponding to a linear density of 319 ktex made of polyester: Fibre rope ISO 10547 - 20 - PES EXAMPLE 2 Designation of a higher strength double braided rope,
42、reference number 20, corresponding to a linear density of 319 ktex made of polyester: Fibre rope ISO 10547 - 20 - PES (hs) Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10547 2 ISO 2008 All rights reserved 5 General requirements 5.1 Construction R
43、opes produced according to this document shall be made in the following construction. The rope (see Figure 1) shall be a double braided construction wherein an inner braid of hollow structure manufactured in a separate operation shall serve as the core, while a cover (outer braid) is braided over it
44、 in a second operation. The weight of either the inner braid or the outer braid shall not exceed 55 % of the total weight of the rope. It shall also conform to ISO 9554. Figure 1 Shape of a polyester double braided rope and of a polyester higher strength double braided rope 5.2 Number of strands For
45、 ropes of reference number from 6 to 16, the minimum number of strands of outer braid shall be 16. For ropes of reference number greater than 16, the minimum number of strands of outer braid shall be 24. 5.3 Manufacture and labelling Manufacture, labelling, packaging, invoicing and delivery lengths
46、shall conform to ISO 9554. 5.4 Strand interchange 5.4.1 Strand interchange shall be the overlapping continuation of a single interrupted strand (or multiple strand) with another identical strand which follows the identical path in the braid. Although it is desirable that no strand interchange be pre
47、sent in the core or the cover of any size and length of rope, some methods of manufacture impose limitations. To compensate for these limitations, strand interchange shall be in accordance with 5.4.2 to 5.4.5. 5.4.2 To allow for a braider malfunction, one strand interchange shall be permitted in the
48、 core and one in the cover for standard length of 200 m or less. 5.4.3 For lengths greater than 200 m, additional strand interchanges shall be permitted if deemed necessary by the manufacturer. 5.4.4 In producing the strand interchanges, the distance of the overlapping shall be equivalent to 8 times
49、 the rope size number but not less than 600 mm for ropes whose reference numbers are 72 and less. Strand interchanges shall be at least 12 m apart measured from interchange centre to interchange centre. 5.4.5 Because strand interchanges within the core are difficult to detect after application of the cover, a record of verifiable information attes