《08-30182212-DC.pdf》由会员分享，可在线阅读，更多相关《08-30182212-DC.pdf（17页珍藏版）》请在三一文库上搜索。
1、a Date: 5 September 2008 Origin: European Latest date for receipt of comments: 31 December 2008 Project no.: 2008/01535 Responsible committee: B/513 Construction equipment and plant and site safety Interested committees: Title: Draft BS EN 13862:2001/A1 Floor cutting-off machines - Safety Supersessi
2、on information: If this document is published as a standard, the UK implementation of it will supersede BSEN13862 : 2001 and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT
3、AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 December 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for informa
4、tion on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-ma
5、il within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations
6、 represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site
7、http:/. Direct tel: 020 8996 7224 Responsible Committee Secretary: Mr M J Hodson (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30182212 DC Licensed CopyChinese University of H
8、ong Kong, 21/10/2008 08:12, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent British Standard. If no comments are recei
9、ved to the contrary, then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe
10、, the UK will be obliged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given b
11、elow is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given
12、on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted shou
13、ld be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3)
14、4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs cl
15、arifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered
16、trademarks, and Windows is a trademark of Microsoft Corporation. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:12, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM FINAL DRAFT EN 13862:2001 prA1 August 2008 ICS 93.080.10 English Version Floor cutting-off mac
17、hines - Safety Machines scier les sols - ScuritBodentrennschleifmaschinen - Sicherheit This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 151. This draft amendment A1, if approved, will modify the European Standard
18、 EN 13862:2001. If this draft becomes an amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. This draft amendment was established by CEN in thre
19、e official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of A
20、ustria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Warning :
21、This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue
22、 de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13862:2001/prA1:2008: E Licensed CopyChinese University of Hong Kong, 21/10/2008 08:12, Uncontrolled Copy, (c) BSI EN 13862:2001/prA1:2008 (E) 2 C
23、ontents Page Foreword3 1 Modification to the Foreword .4 2 Modification to the Introduction.4 3 Modification to Clause 1, Scope.4 4 Modification to Clause 2, Normative references 4 5 Modification to Clause 3, Terms and definitions6 6 Modification to Table 1 List of significant hazards6 7 Modificatio
24、n to Clause 5, Safety requirements and/or measures.6 8 Modification to 5.1.2.1, Transmission parts6 9 Modification to 5.1.5, Transport and handling6 10 Modification to 5.1.8.1, General7 11 Modification to 5.2.1, General.7 12 Modification to 5.2.2, Water pump .7 13 Modification to 5.3, Thermal hazard
25、s 7 14 Modification to Clause 7, Information for use 7 15 Modification to Annex A (informative) Noise test code Grade 2 of accuracy 8 16 Modification to Figure D.1.9 17 Addition of Annex F.10 18 Modification of Annex ZA .14 19 Addition of Annex ZB15 Licensed CopyChinese University of Hong Kong, 21/1
26、0/2008 08:12, Uncontrolled Copy, (c) BSI EN 13862:2001/prA1:2008 (E) 3 Foreword This document (EN 13862:2001/prA1:2008) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines Safety”, the secretariat of which is held by DIN. This document is curren
27、tly submitted to the Unique Acceptance Procedure. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annexes ZA
28、 or ZB, which are integral parts of this document. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:12, Uncontrolled Copy, (c) BSI EN 13862:2001/prA1:2008 (E) 4 1 Modification to the Foreword Replace the 5th paragraph with the following: “For relationship with EU Directive(s), see informa
29、tive Annexes ZA and ZB, which are integral parts of this document.“. Delete the 6th paragraph “The annex A is normative and contains “Noise test code - Grade 2 of accuracy“, annex B is normative and contains “Dimensions of the flanges for cutting-off diamond wheels“, annex C is normative and contain
30、s “Strength of guards - State of the art concerning the characteristics of guards used with cutting-off wheels“, annex D is normative and contains “Pictograms“, the annex E is normative and contains “Verification of surface temperature“ and the annex ZA is informative and contains “Relationship of t
31、his document with EC Directives“.“. 2 Modification to the Introduction 1st paragraph: Replace “EN 292“ with “EN ISO 12100-1:2003“. 3 Modification to Clause 1, Scope 1st paragraph, 1st sentence: Delete “self-propelled ride on1) and“. Consequently, delete footnote to text 1). 5th paragraph: Add as fir
32、st indent: “ self-propelled ride-on floor sawing machines;“. 4 Modification to Clause 2, Normative references Replace the standard paragraph with the following: “The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap
33、plies. For undated references, the latest edition of the referenced document (including any amendments) applies.“. Replace “EN 953:1997“ with “EN 953“. Replace “ISO 6395:1988“ with “ISO 6395:2008“. Delete: “EN 292-1:1991, Safety of machinery Basic concepts, general principles for design Part 1: Basi
34、c terminology, methodology EN 292-2:1991, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles and specifications“, Licensed CopyChinese University of Hong Kong, 21/10/2008 08:12, Uncontrolled Copy, (c) BSI EN 13862:2001/prA1:2008 (E) 5 “EN 563:1994, Safety
35、of machinery Temperatures of touchable surfaces Ergonomic data to establish temperature limit values for hot surfaces“, “EN 954-1:1996, Safety of machinery Safety related parts of control systems Part 1: General principles of design“ and “EN 1070:1998, Safety of machinery Terminology“. Replace: “prE
36、N 13218:1998“ with “EN 13218:2002“. Replace “EN 60204-1:1997, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:1997)“ with “EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:2005, modified)“.
37、Replace “EN 60335-1:1994, Safety of household and similar appliances Part 1: General requirements (IEC 60335-1:1991, modified)“ with “EN 60335-1:2002, Household and similar electrical appliances Safety Part 1: General requirements (IEC 60033-1:2001, modified)“. Replace “EN 60335-2-41:1996, Safety of
38、 household and similar appliances Part 2: Particular requirements for electric pumps for liquid having a temperature not exceeding 35 C (IEC 60335-2-41:1996)“ with “EN 60335-2-41:2003, Household and similar electrical appliances Safety Part 2-41: Particular requirements for pumps (IEC 60335-2-41:200
39、2)“. Replace “EN 61029-1:1995“ with “EN 61029-1:2000“. Replace “EN ISO 3744:1995, Acoustics Determination of sound power levels of noise sources using sound pressure Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994)“ with “prEN ISO 3744:2006, Acoustics Determina
40、tion of sound power levels and sound energy levels of noise sources using sound pressure Engineering method for an essentially free field over a reflecting plane (ISO/DIS 3744:2006)“. Replace “ISO 6104:1979, Abrasive products Diamond or cubic boron nitride grinding wheels and saws General survey, de
41、signation and multilingual nomenclature“ with “ISO 6104:2005, Superabrasive products Rotating grinding tools with diamond or cubic boron nitride General survey, designation and multilingual nomenclature“. Replace “ISO 7000:1989“ with “ISO 7000:2004“. Add: “EN 206-1:2000, Concrete Part 1: Specificati
42、on, performance, production and conformity“, “EN ISO 5349-2:2001, Mechanical vibration Measurement and evaluation of human exposure to hand- transmitted vibration Part 2: Practical guidance for measurement at the workplace (ISO 5349-2:2001) EN ISO 8041:2005, Human response to vibration Measuring ins
43、trumentation (ISO 8041:2005)“, “EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12
44、100-2:2003) EN ISO 13732-1:2006, Ergonomics of the thermal environment Methods for the assessment of human responses to contact with surfaces Part 1: Hot surfaces (ISO 13732-1:2006) EN ISO 13849-1:2006, Safety of machinery Safety-related parts of control systems Part 1: General principles for design
45、 (ISO 13849-1:2006) Licensed CopyChinese University of Hong Kong, 21/10/2008 08:12, Uncontrolled Copy, (c) BSI EN 13862:2001/prA1:2008 (E) 6 EN ISO 20643:2005, Mechanical vibration Hand-held and hand-guided machinery Principles for evaluation of vibration emission (ISO 20643:2005)“, “ISO 5348:1998,
46、Mechanical vibration and shock Mechanical mounting of accelerometers“ and “ISO 16063-1:1998, Methods for the calibration of vibration and shock transducers Part 1: Basic concepts“. 5 Modification to Clause 3, Terms and definitions Standard paragraph: Replace “EN 1070:1998“ with “EN ISO 12100-1:2003“
47、. Definition of 3.6: Replace “ISO 6104:1979“ with “ISO 6104:2005“. 6 Modification to Table 1 List of significant hazards Add as last item: “4.31 Hazards generated by vibration Annex F“ 7 Modification to Clause 5, Safety requirements and/or measures 1st hanging paragraph: Replace “EN 292-1:1991 and E
48、N 292-2:1991“ with “EN ISO 12100-1:2003 and EN ISO 12100-2:2003“. 2nd hanging paragraph: Replace “EN 953:1997“ with “EN 953“ and “EN 60204-1:1997“ with “ EN 60204-1:2006“. 8 Modification to 5.1.2.1, Transmission parts 1st paragraph, 2nd sentence: Replace the 2nd sentence with the following: “These g
49、uards shall comply with EN 953 and 5.3.2.2 of EN ISO 12100-2.“. 3rd paragraph: Delete the 3rd paragraph, listings and NOTE. 9 Modification to 5.1.5, Transport and handling NOTE: Replace “1.1.5 of EN 292-1:1991, Annex A“ with “5.5.5 of EN 12100-2:2003“. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:12, Uncontrolled Copy, (c) BSI E