《08-30189894-DC.pdf》由会员分享，可在线阅读，更多相关《08-30189894-DC.pdf（27页珍藏版）》请在三一文库上搜索。
1、a Date: 23 September 2008 Origin: European Latest date for receipt of comments: 31 December 2008 Project no.: 2008/02978 Responsible committee: EPL/278 Road transport informatics Interested committees: Title: Draft BS EN ISO 17264 Road transport and traffic telematics - Automatic vehicle and equipme
2、nt identification - Interfaces Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details belo
3、w). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 December 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be s
4、ent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is lim
5、ited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on t
6、he co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online
7、 Service on the BSI web site http:/. Direct tel: 020 8996 7127 Responsible Committee Secretary: Mr M S Matharu (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30189894 DC Licens
8、ed CopyChinese University of Hong Kong, 21/10/2008 08:43, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent British Stan
9、dard. If no comments are received to the contrary, then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives t
10、he necessary support in Europe, the UK will be obliged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. S
11、ubmission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee S
12、ecretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirement
13、s. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Do
14、cument: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Defini
15、tion is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Micros
16、oft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:43, Uncontrolled Copy, (c) BSI DRAFT INTERNATIONAL STANDARD ISO/DIS 17264 ISO/TC 204 Secretariat: ANSI Voting begins on Voting terminates on 2008
17、-09-18 2009-02-18 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION Road transport and traffic telematics Automatic vehicle and equipment identification Interfaces Transport routier et tlmatique du trafic - Identification automatique des vhicules et de leur
18、quipement - Interfaces ICS 03.220.20; 35.240.60 ISO/CEN PARALLEL ENQUIRY ISO/CEN PARALLEL ENQUIRY This draft International Standard is a draft standard developed within the European Committee for Standardization (CEN) and processed under the CEN-lead mode of collaboration as defined in the Vienna Ag
19、reement. The document has been transmitted by CEN to ISO for circulation for ISO member body voting in parallel with CEN enquiry. Comments received from ISO member bodies, including those from non-CEN members, will be considered by the appropriate CEN technical body. Should this DIS be accepted, a f
20、inal draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS vote in ISO and formal vote in CEN. In accordance with the provisions of Council Resolution 15/1993 this document is circulated in the English language only. Conformment aux dispositions de la R
21、solution du Conseil 15/1993, ce document est distribu en version anglaise seulement. To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la
22、 distribution, le prsent document est distribu tel quil est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO C
23、HANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
24、TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. International Organization for Standardization,
25、 2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 08:43, Uncontrolled Copy, (c) BSI ISO/DIS 17264 ii ISO 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be
26、edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is
27、a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member
28、 bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users
29、country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be address
30、ed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreem
31、ent. Violators may be prosecuted. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:43, Uncontrolled Copy, (c) BSI Licensed CopyChinese University of Hong Kong, 21/10/2008 08:43, Uncontrolled Copy, (c) BSI ISO/DIS 17264 ii ISO 2008 All rights reserved Contents Page Foreword.iii Introductio
32、niv 1 Scope5 2 Conformance5 3 Normative references5 4 Terms and definitions .7 5 Symbols and abbreviated terms 8 6 Requirements.9 6.1 AVI/AEI transaction profiles .9 6.1.1 AVI/AEI read transaction profile.9 6.1.2 AVI/AEI read and write transaction profile. 10 6.1.3 Air interface definitions 10 7 Tes
33、t methods. 10 Annex A (normative) AVI/AEI Application interface using EN12834/ ISO 15628. 11 A.1 Usage of the DSRC application layer 11 A.2 Initialisation phase . 11 A.2.1 Overview 11 A.2.2 AVI/AEI Application-specific contents of the BST 11 A.2.3 AVI/AEI Application-specific contents of the VST. 12
34、 A.3 Transaction phase 13 A.4 AVI/AEI attributes 14 A.5 AVI/AEI Container module definition 15 Annex B (normative) AVI/AEI transactions using ISO/IEC 18000. 18 Annex C (informative) AVI/AEI transaction examples 19 C.1 Simple AVI transaction. 19 C.1.1 Beacon service table content 19 C.1.2 Vehicle ser
35、vice table (VST) content 20 C.2 AVI transaction with GET. 21 C.2.1 Beacon service table (BST) content . 21 C.2.2 Vehicle service table (VST) content 21 C.2.3 GET Request content . 22 C.2.4 GET Response content 23 Licensed CopyChinese University of Hong Kong, 21/10/2008 08:43, Uncontrolled Copy, (c)
36、BSI ISO/DIS 17264 ISO 2008 All rights reserved iii Foreword This document prEN ISO 17264:2008 has been prepared by Technical Committee CEN/TC 278 “Road transport and traffic telematics”, the secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 204 “Intelligent transp
37、ort systems”. This document is currently submitted to the parallel Enquiry. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:43, Uncontrolled Copy, (c) BSI ISO/DIS 17264 iv ISO 2008 All rights reserved Introduction This International Standard provides requirements for interoperable ITS tr
38、ansactions in an Automatic Vehicle Identification (AVI), Automatic Equipment Identification (AEI) or Electronic Registration Identification (ERI) context. An AVI/AEI transaction is based on defined sets of AVI/AEI functions and data attributes as specified in this International Standard. NOTE The pr
39、incipal definitions of AVI, AEI, ERI are to be found in EN ISO 14814, EN ISO 14815, EN ISO 14816, CEN ISO/TS 17261, CEN ISO/TS 17262, CEN ISO/TS 17263, CEN ISO/TS 24534 (all parts), ISO TS 24535. This International Standard specifies an application interface for AVI/AEI systems, based on standardise
40、d air interface protocols enabling interoperability between different AVI/AEI service providers. In order to achieve full interoperability, AVI/AEI service providers will additionally have to agree on issues such as: protocol implementation conformance statements from manufacturers, detailing which
41、optional features in the AVI/AEI transaction and air interface protocol that are actually being implemented and used; any contractual agreements needed between AVI/AEI service providers in order to regulate the handling of different AVI/AEI transactions. NOTE The definitions and examples provided in
42、 this International Standard may also be used in an ERI context, and those interested in this context are advised to also refer to ISO 24534 (all parts) and ISO 24535. This International Standard has the following structure: The first four clauses comprise the scope, normative references, definition
43、s of terms and abbreviations. In Clause 5, the AVI/AEI transaction requirements are defined, which are independent of any air interface protocol. In Normative Annex A, the AVI/AEI application interface architecture is described in terms of its relation to the DSRC communication architecture, based o
44、n EN12834/ISO 15628. In Normative Annex B, the AVI/AEI application interface architecture is described in terms of its relation to the air interfaces defined by the ISO/IEC 18000 series. In Informative Annex C, AVI/AEI transaction examples are provided. Licensed CopyChinese University of Hong Kong,
45、21/10/2008 08:43, Uncontrolled Copy, (c) BSI prEN ISO 17264:2008 (E) 5 1 Scope The scope of this International Standard is to provide the specifications of: common AVI/AEI transaction requirements, which define the common steps of any AVI/AEI transaction; AVI/AEI application interface to standardise
46、d wireless protocols (referred to as the Air Interface) supporting the AVI transaction requirements, so as to enable interoperability. In Figure 1 below the conceptual architecture model is shown for AVI transactions between On-board Equipment and Fixed Equipment. The air interface concerns the refe
47、rence point DELTA in EN ISO 14814. Figure 1 : Overall conceptual reference architecture model showing the context of AVI /AEI EN ISO 14814 This is an interface standard adhering to the open systems interconnection (OSI) philosophy (ISO/IEC 7498-1), and it is as such not concerned with the implementa
48、tion choices to be realised at either side of the air interface between the Fixed Equipment and OBE. 2 Conformance Conformance may be claimed where equipment conforms to the provisions of this International Standard. No specific performance tests are defined within this International Standard. 3 Nor
49、mative references This International Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of a