《AA-TAN-1-2005.pdf》由会员分享，可在线阅读，更多相关《AA-TAN-1-2005.pdf（48页珍藏版）》请在三一文库上搜索。
1、REGISTRATION RECORD SERIES o Tempers For Aluminum And Aluminum Alloy Products Metric Edition The Aluminum Association Incorporated 1525 Wilson Boulevard, Suite 600, Arlington, VA 22209 www.aluminum.org Revised: November 2005 Supersedes: August 2001 Copyright The Aluminum Association Inc. Provided by
2、 IHS under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 04:15:38 MDTNo reproduction or networking permitted without license from IHS -,-,- Use of the Information The Aluminum Association has used its best efforts in Compiling the information contain
3、ed in this publication. Although the Association believes that its compilation procedures are reliable, it does not warrant, either expressly or impliedly, the accuracy or completeness of this information. The Aluminum Association assumes no responsibility or liability for the use of the information
4、 herein. All Aluminum Association published standards, data, specifications and other material are reviewed at least every five years and revised, reaffirmed or withdrawn. Users are advised to contact The Aluminum Association to ascertain whether the information in this publication has been supersed
5、ed in the interim between publication and proposed use. Copyright The Aluminum Association Inc. Provided by IHS under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 04:15:38 MDTNo reproduction or networking permitted without license from IHS -,-,- Lis
6、ted in this booklet, in metric units only, are the tempers for aluminum and aluminum alloy products registered with The Aluminum Association but not contained in The Associations Aluminum Standards and Data Metric SI. This is the third publication of the registration record of “Tempers for Aluminum
7、and Aluminum Alloy Products-Metric Edition”. For most parts the method of preparation has been to arrive at logical metric values rather than to restate current inch-pound values in metric terms by use of conversion factors. The metric units in this publication are based on the International System
8、of Units (SI). The strength properties are expressed in megapascal (MPa). Refer to APPENDIX A, “Guidelines for Metric Conversion of Yellow Sheets”, for specific conversion procedures, and to the Yellow Sheets (Tempers for Aluminum and Aluminum Alloy Products) for registered tempers with limits shown
9、 in customary units from which this documents met- ric limits are derived. Some of the registered tempers may be the subject of U.S. patents or patent applications, and their listing herein is not to be construed in any way as the granting of a license under such patent rights. Tempers for wrought p
10、roducts are given on pages 1-28 and for castings on page 29. Inactive alloys and tempers are listed on pages 32-38. An explanation for The Aluminum Associations “Temper Designation System” is given in the Aluminum Standards and Data-Metric SI and in the American National Standard ANSI H35.1 (M). All
11、 new registrations and changes to previously registered mechanical property limits are marked and defined. In addition, the registration column also includes a revision date to in- dicate changes to the property limits originally registered. I Copyright The Aluminum Association Inc. Provided by IHS
12、under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 04:15:38 MDTNo reproduction or networking permitted without license from IHS -,-,- TEMPER REGISTRATION When any aluminum or aluminum alloy material is produced in a temper not previously applied to
13、that mate- rial, the temper, along with the alloy designation and product form to which it applies, may be registered with The Aluminum Association. PROCEDURE FOR INDIVIDUAL REGISTRATION OF TEMPERS 1. Any person, firm or corporation may apply to The Aluminum Association to register a new temper. 2.
14、Selection of the temper designation usually is left to the discretion of the Technical Committee on Product Standards, but consideration will be given to the applicant?s choice when circumstances so warrant. 3. The temper is registered when, in the opinion of the Technical Committee on Product Stand
15、ards, it is judged to be technically correct and complete with respect to the following: a. The temper designation conforms to ANSI H35.1 (M) ?Alloy and Temper Designation Systems for Aluminum? (reprinted in The Aluminum Association manual Aluminum Standards and Data-Metric SI). b. The material is o
16、ffered for sale in the proposed temper and is available for use by more than one user. c. The mechanical property limits applicable to the temper are included. (Limits are shown as tentative unless established in accordance with the data base criteria outlined under ?Mechanical Properties? in Sectio
17、n 6, ?Standards Section? of the Aluminum Standards and Data-Metric S I ) . d. The following additional information is included when characteristics, in addition to mechanical prop- erties, are specified for the temper: (1) Test methods by which conformance with the requirements for specified charact
18、eristics can be (2) Details of the practice to be followed in producing the temper. evaluated, OR e. The minimum tensile strength limit applicable to the O temper accompany the request for registration of H tempers. f. The indication of a variation in treatment of a basic T temper is limited to one
19、additional digit (exclud- ing zero) unless all available digits have been used, and except as provided for in the Appendix to ANSI H35.1(M). II Copyright The Aluminum Association Inc. Provided by IHS under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/200
20、7 04:15:38 MDTNo reproduction or networking permitted without license from IHS -,-,- TEMPER REGISTRATION (continued) PROCEDURES FOR ALUMINUM ASSOCIATION TECHNICAL DIVISION (AATD) REGISTRATION OF TEMPERS A temper for an aluminum alloy material may be registered as an AATD temper when, through formal
21、ballot of the Technical Committee on Product Standards, it is judged to be technically correct with respect to the following: a. The temper designation conforms to ANSI H35.1(M) “Alloy and Temper Designation Systems for Aluminum” (reprinted in The Aluminum Association manual Aluminum Standards and D
22、ata-Metric SI). b. The material is offered for sale in the proposed temper by more than one producer. c. The minimum and/or maximum mechanical property limits applicable to the temper are included. d. The following additional information is included when characteristics, in addition to mechanical pr
23、op- erties, are specified for the temper: (1) Test methods by which conformance with the requirements for the specified characteristics can (2) Details of the practices to be followed in producing the temper. be evaluated, OR e. The minimum tensile strength limit applicable to the O temper accompany
24、 the request for registration of H tempers. f. The indication of a variation in treatment of a basic T temper is limited to one additional digit (exclud- ing zero) unless all available digits have been used, and except as provided for in the Appendix to ANSI H35.1(M). g. The temper is not being appl
25、ied to an alloy designated as experimental (with prefix “X). REQUIREMENTS FOR PROPOSED CHANGES TO REGISTERED TEMPERS Proposed changes to a registered designations mechanical properties and/or characteristics: a. Require approval by formal ballot of the Technical Committee on Product Standards for re
26、gistered tempers having “minimum” and/or “maximum” mechanical property limits. b. Require a 30-day review by the Technical Committee on Product Standards for registered tempers having “tentative” mechanical property limits, or tempers applied to experimental alloys (with prefix “X”). The registrant
27、has the final authority to change the temper limits, provided the change complies with item 3 under Individual Registration of Tempers. Changes proposed by others than the regis- trant are acceptable only with the approval of the registrant. REQUIREMENTS FOR DELETION OF TEMPERS FROM THE REGISTRATION
28、 LIST 1. When any alloy is removed from the active alloy registration list, all tempers applicable to that alloy are automatically removed from the active temper registration list. 2. Approval of the Technical Committee on Product Standards through formal ballot is required to effect deletion of any
29、 registered temper from the active registration list, except as provided by the preceding sentence. . 111 Copyright The Aluminum Association Inc. Provided by IHS under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 04:15:38 MDTNo reproduction or netwo
30、rking permitted without license from IHS -,-,- This page left intentionally blank. Copyright The Aluminum Association Inc. Provided by IHS under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 04:15:38 MDTNo reproduction or networking permitted without
31、 license from IHS -,-,- f the listed DroDerties is as WROUGHT PRODUCl 1 1 00-1 2: Remark$ Classificatioi Alloy Temper 1100-02 1100-Hl51 11 00-Hl 81 11 00-Hl 85 1100-Hl9 11 00-Hl 91 1200-0 1200-H112 1200-Hl2 1200-Hl4 1200-Hl6 1200-Hl8 1235-0 1235-0 1235-Hl 8 1235-HI 11 Footnotes appe pecified in the
32、column headed “B; S“ t i$ - Registered Thickness, mrn Tem ! Strength, WPa - Basis Perc 50mm 15 _ I 1 1 - 25 35 35 3 30 Product - Over - Yielc Date Ult. 50 or 5.65 d - t* 22 * * Thru 0.30 0.50 1.60 0.50 Vumax Alcoa Alcoa AATD Alcoa Alcoa - AATD AATD AATD AATD 4ATD 4ATD - 4lcoa 4lcoa 4lcoa Alcoa 04/04
33、/78 02/23/56 Fin Stock Tube Sheet Impact Wire Sheet 0.13 0.32 0.70 0.15 0.32 Min Max Min Min Min6 Min Min 75 110 115 145 150 165 160 3! 14 14 15 Minimum amount of cold work controlled. Temper controlled within espe- cially close limits. Extra hard temper closely con- trolled. 07ioii6a 07/01/68 07/01
34、/68 07/01/68 37/01/68 37/01/68 Sheet beet iheet din dax din Aax din -in Stock -in Stock -in Stock Vire Vire din din leynolds eynolds AATD Alcoa Alcoa Alcoa Alcoa 3eynolds eynolds 15/17/63 1511 7/63 15/28/71 16/20/69 39/09/69 09/09/69 10/20/87 Revised 03/09/95 06/16/94 Revised 10129198 1211 9/95 Revi
35、sed 10/29/98 1345-H24 1345-H26 1350-H113 1350-H 141 1350-H 142 1350-Hl61 2008-T4 Min Max Win Max din .vinin Max Min - Min - Min Min - 105 - 110 110 - zonforms to ICEA requirements or solid conductors. Vire Vire .Vire Nire Sheet 10.00 10.00 10.00 - 1.90 - 1.80 1.80 - 0.63 - 0.63 0.63 .4pplicable to i
36、nsulated conduc- tors and currently specified as “1/2 to 3i4 hard“. Applicable to insulated conduc- tors and currently specified as “314 to full hard“. 22 22 22 10 2010-T4 2010-T41 Sheet Sheet The material shall exhibit (1) No lines or ridges in the rolling di- rection after buffing or polishing a b
37、lank, typically 50 mm by 230 mm, oriented with the long axis in the long transverse direction and stretching 5%, or (2) Random dis- tribution of grain orientations with no continuous bands of cube oriented grains as determined by microtexture analysis of the rolling surface of the sheet us- ing orie
38、ntation image microscopy (OIM). - 9 2011-T6 beet sheet late Teynolds eynolds Alcoa Boeing Boeing Alcoa Alcoa Alcoa Alcan Fracture Touahnes-Min Kic For thicknesses over 40.00 thru 50.00 mm L-T direction 29 MPafi T-L direction 25 MPafi S-L direction 21 MPafi For thicknesses over 50.00 thru 100.00 mrn
39、L-T direction 29 MPafi T-L direction 24 MPafi S-L direction 22 MPafi For thicknesses over 100.00 thru 160.00 mm L-T direction 27 MPafi T-L direction 23 MPafi S-L direction 23 MPafi ?224-T3510 standard 2024 heat treat- ment. Standard 2024 solution treat- ment and quench followed by 11% nominal cold r
40、oll and 1% minimum stretcher stress relief. :xtrusion late Sheet 8 iate Extruded 3od, Bar, rofiles :xtrusion late *Tentative Copyright The Aluminum Association Inc. Provided by IHS under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 04:15:38 MDTNo re
41、production or networking permitted without license from IHS -,-,- Classif icatioi dumn headed “Basis“ WROUGHT PRODUCTS )ecified in the Thickness, mrn if the listed prop Regis tered es is as Product ixtruded Vof il es 2027-209 Remark$ Strength, ir? - Perct 50mm - E Ult. - Yield Alloy Temper - Thru 40
42、.00 Date Over - 20.00 5D or 5.65 .i BY Alcan 3eynolds 3eynolds Pechiney Alcoa Alcoa Alcoa Alcoa !027-T351 51 5 395 12 11/29/04 Fracture TouahnessI4- min KI, For thicknesses over 20.00 thru 40.00 mm L-T direction 44 MPafi T-L direction 42 MPafi !038-T4 !038-T6 10/10/82 1 O l l 0182 Sheet Sheet 0.63 0
43、.63 1.60 3.20 - 1.80 1.80 3.20 6.00 - Min Min 275 345 140 305 20 8 Automotive sheet. Automotive sheet. Sheet Ming Ming 430 430 285 275 15 16 12/10/03 !090-T3 !090-T83 !090-T86 02/28/89 Revised 03/23/99 03/15/88 Revised 03/09/98 O811 1/88 Revised 07/30/90 Sheet Sheet fxtrusion 0.80 0.80 3.20 3.20 6.3
44、0 - 00.00 125.00 - 6.30 3.20 6.30 3.20 6.30 12.50 - 125.00 60.00 - Min Min6 Ming Min Ming Min Min Min Ming 31 5 530 505 51 5 505 540 540 550 525 21 5 485 455 485 455 490 490 505 470 Min Ming Min Min Ming Min“ - 5 425 425 41 5 420 420 395 - !097-T87 06/08/01 late *Tentative Fracture Touahness14- min
45、KI, For thicknesses over 100.00 thru 125.00 mm L-T direction 36 MPa fi T-L direction 28 MPa fi S-L direction 20 MPa fi For thicknesses over 125.00 thru 160.00 mm L-T direction 32 MPa fi T-L direction 27 MPa fi S-L direction 20 MPa fi 385 385 380 380 380 360 5 3 1.5 4 3 1.5 Exfoliation Corrosion Resi
46、stance See Footnote 15.b Stress Corrosion Direct Tensile Specimens ma- chined and tested in accordance with ASTM G47 shall show no evidence of stress corrosion failure when tested in the short transverse direction at 240 Mpa and exposed for 30 days ootnotes appear beginning on page 3 Copyright The A
47、luminum Association Inc. Provided by IHS under license with AA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 04:15:38 MDTNo reproduction or networking permitted without license from IHS -,-,- WROUGHT PRODUCTS : the listed DroDerties is as SDecified in the column hea
48、ded “Basis9- Classification Thickness, mm 297-2397 Alloy Temper II .- Tensile Strength, .- Ition if? 5D or 5.65 d - - Remarks Registered Elon Perce 50mm - gasis Min6 Min9 Minio Min6 Ming MinO Min6 Ming MinO Min6 Ming MinO Min6 Ming Minlo Min6 Ming MinO - iIpa Olt. 440 455 450 435 440 440 425 440 425 430 430 405 420 420 400 41 5 41 5 395 - field 2_ Thru 50.00 - 60.00 80.00 00.00 25.00 60.00 Product Over 40.00 50.00 60.00 80.00 00.00 25.00 Date 16/21 /O0 Revised )6/03/04 B Y vcCook detal