《AS-NZS-3350.1-2002.pdf》由会员分享，可在线阅读，更多相关《AS-NZS-3350.1-2002.pdf（158页珍藏版）》请在三一文库上搜索。
1、AS/NZS 3350.1/AMD 4/2007-11-30 STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND Amendment No. 4 to AS/NZS 3350.1:2002 Safety of household and similar electrical appliances Part 1: General requirements REVISED TEXT The 2002 edition of AS/NZS 3350.1 is amended as follows; the amendments should be inserted in
2、 the appropriate places. SUMMARY: This amendment applies to Preface, Clauses 4, 11, 19, 22, 25, 30 and Annexes S and ZZ. Published on 30 November 2007. Approved for publication in Australia on behalf of the Council of Standards Australia on 2 November 2007 Approved for publication in New Zealand by
3、the Standards Council of New Zealand on 13 October 2007 This amendment takes effect from the date of publication. PREFACE Replace the second paragraph by the following. This Standard incorporates Amendment No. 1 (November 2003), Amendment No. 2 (May 2004), Correcting Amendment No. 3 (January 2005) a
4、nd Amendment No. 4 (November 2007). The changes introduced by the Amendments are indicated in the text by a marginal bar and amendment number against the clause, note, table, figure or part thereof affected. Where an application date other than immediate is applicable to an amendment the date of app
5、lication (DOA) is indicated by the marginal bar against the part affected. 4 General conditions for the tests 4.2In Note 1 replace the struck through dash item and the shaded dash item by the following: If the tests of 24.1.3 are carried out, three switches or three additional appliances are needed.
6、 11 Heating 11.8Delete Note 201 Table 3 Replace the text of struck through footnote 5) and shaded footnote 5) by the following: 5) There is no specific limit for thermoplastic material. However, the temperature rise has to be determined in order that the tests of 30.1 can be carried out. ISBN 0-7337
7、-8429-1 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 19 Abnormal operation Table 7 Replace the text of struck through footnote 3) and shaded footnote 3) by the following: 3) There is no specific limit for supplementary insulation and reinforced insulation of thermoplastic material. Howev
8、er, the temperature rise has to be determined in order that the tests of 30.1 can be carried out. 22 Construction 22.201Replace the text by “VOID” 25 Supply connection and external flexible cords Table 9 Replace the struck through table entries and the shaded table entries by the following: 3 and ?
9、6 0,75 6 and ? 10 1,0 30 Resistance to heat and fire 30.1Replace the struck through and the shaded paragraphs by the following: Compliance is checked by subjecting the relevant part to the ball pressure test made by means of the apparatus shown in figure 12. Annex S 17 Endurance Replace the struck t
10、hrough and the shaded paragraphs by the following: Compliance is checked on three separate appliances or switches. Annex ZZ Delete the deviations for 4.2, 11.8, Table 3 footnote 5, Table 7, 22.201, Table 9 (relating to the third and fourth lines), 30.1 and Annex S Accessed by UNIVERSITY OF SOUTH AUS
11、TRALIA on 31 May 2008 This page has been left intentionally blank. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 AS/NZS 3350.1/AMD 3/2005-01-31 STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND Amendment No. 3 to AS/NZS 3350.1:2002 Safety of household and similar electrical appliances Part 1: Gen
12、eral requirements CORRECTION The 2002 edition of AS/NZS 3350.1 is amended as follows; the amendment should be inserted in the appropriate places. SUMMARY: This amendment applies to Figure 10, Annex A and Annex ZZ Published on 31 January 2005 All parts of this Amendment form part of the standard from
13、 the date of publication. Annex A A1.1 Add the following as the first reference Approval and test specification Plugs and socket-outlets AS/NZS 3112 2000 Annex ZZ After clause 30.3 insert the following variation Annex A A1.1 As the first reference insert the following variation: Approval and test sp
14、ecification Plugs and socket-outlets AS/NZS 3112 2000 ISBN 0 7337 6480 0 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 Figure 10Replace the drawing by the following. A B C 37 80 20 (10) ?12 -0,05 0 ?12 +0,05 0 R = 2 0,05 ?14 60 105 M3 37 23 6242 0,2 0,02 2 7 27 35 X X 2:1 M3 10 25 7,6 14
15、C Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 This page has been left intentionally blank. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 AS/NZS 3350.1/AMD 2/2004-05-31 STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND Amendment No. 2 to AS/NZS 3350.1:2002 Safety of household and simi
16、lar electrical appliances Part 1: General requirements REVISED TEXT The 2002 edition of AS/NZS 3350.1 is amended as follows; the amendments should be inserted in the appropriate places. SUMMARY: This amendment applies to Clauses 30.2.2, 30.2.3 and Annex ZZ Published on 31 May 2004 Approved for publi
17、cation in Australia on behalf of the Council of Standards Australia on 18 March 2004 Approved for publication in New Zealand by the Standards Council of New Zealand on 26 March 2004 All parts of this Amendment form part of the standard from the date of publication. 30.2.2 Replace the second and thir
18、d paragraphs of the shaded text by the following: Where an insulating material is within 3 mm of a current carrying connection but is shielded from the connection by a different material, the glow-wire test of annex K is carried out at the relevant temperature on the shielded material as follows. Th
19、e glow-wire tip is applied to the insulating material to be tested via the shielding material, the glow-wire tip penetration limit of 7 mm 0,5 mm being reduced to 3 mm 0,2 mm. 30.2.3 Replace the second and third paragraphs of the shaded text by the following: Where an insulating material is within 3
20、 mm of a current carrying connection but is shielded from the connection by a different material, the glow-wire test of annex K is carried out at the relevant temperature on the shielded material as follows. The glow-wire tip is applied to the insulating material to be tested via the shielding mater
21、ial, the glow-wire tip penetration limit of 7 mm 0,5 mm being reduced to 3 mm 0,2 mm. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 ISBN 0 7337 6151 8 Annex ZZ 30.2.2 Replace the second and third paragraphs of the variation by the following Where an insulating material is within 3 mm of a
22、 current carrying connection but is shielded from the connection by a different material, the glow-wire test of annex K is carried out at the relevant temperature on the shielded material as follows. The glow-wire tip is applied to the insulating material to be tested via the shielding material, the
23、 glow-wire tip penetration limit of 7 mm 0,5 mm being reduced to 3 mm 0,2 mm. 30.2.3 Replace the second and third paragraphs of the variation by the following: Where an insulating material is within 3 mm of a current carrying connection but is shielded from the connection by a different material, th
24、e glow-wire test of annex K is carried out at the relevant temperature on the shielded material as follows. The glow-wire tip is applied to the insulating material to be tested via the shielding material, the glow-wire tip penetration limit of 7 mm 0,5 mm being reduced to 3 mm 0,2 mm. Accessed by UN
25、IVERSITY OF SOUTH AUSTRALIA on 31 May 2008 This page has been left intentionally blank. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 AS/NZS 3350.1/AMD 1/2003-11-14 STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND Am endm ent No. 1 t o AS/ NZS 3350. 1: 2002 Saf et y of househol d and si m i l ar
26、 el ect ri cal appl i ances Part 1: G eneral requi rem ent s ( I EC 60335- 1: 1991, M O D) REVI SED TEXT The 2002 edition of AS/NZS 3350.1 is amended as follows; the amendments should be inserted in the appropriate places. SUM M ARY: This amendment applies to the Preface, Clauses 22.202, 29.1, 30.2,
27、 Annex A and Annex ZZ. Published on 14 November 2003. Approved for publication in Australia on behalf of the Council of Standards Australia on 2nd October 2003. Approved for publication in New Zealand by the Standards Council of New Zealand on 9th September 2003. Pref ace Repl ace t he f our t h and
28、 f i f t h par agr aphs by t he f ol l owi ng. This Standard is an adoption with national modifications and contains the full text of the second impression of IEC 60335-1:1991, Saf et y of Househol d and si m i l ar el ect r i cal Part 1: G ener al r equi r em ent s, including its amendments 1 and 2
29、 and has been varied as indicated to take account of Australian and New Zealand conditions. It also includes the changes detailed in IEC document 61/2121/INF. This part is to be used in conjunction with the appropriate Part 2 of AS/NZS 3350. The Parts 2 contain clauses to supplement or modify the co
30、rresponding clauses in this part to provide the relevant requirements for each type of appliance. This Amendment forms part of the Standard on publication. Af t er 22. 201 add t he f ol l owi ng new subcl ause. 22. 202 Appliances having integrated pins for insertion into socket outlets shall comply
31、with the requirements of AS/NZS 3112. Com pl i ance i s checked as speci f i ed i n Appendi x J of AS/ NZS 3112. NOTE 1 Clause J.2.2.3 (Internal connections for plug portions) of AS/NZS 3112 is covered by clause 23 of this standard. NOTE 2 Clause J.2.2.6.2 (High voltage test) of AS/NZS 3112 is cover
32、ed by clause 16 of this standard, except for the test of the part specified in 2.13.2 (e) of AS/NZS 3112. NOTE 3 Clause J.2.2.6.4 (Temperature rise test) of AS/NZS 3112 is covered by clause 11 of this standard. NOTE 4 Clause J.2.2.6.7 (Equipment with integral pins intended to be supported by the con
33、tacts of a socket- outlet) of AS/NZS 3112 is covered by clause 22.3 of this standard. This Amendment forms part of the Standard on publication. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 ISBN 0 7337 5671 9 25. 1Repl ace t he t ext by t he f ol l owi ng. 25. 1 Appliances, other than tho
34、se intended to be permanently connected to fixed wiring, shall be provided with one of the following means for connection to the supply: -suppl y cord fitted with a plug; - an appliance inlet having at least the same degree of protection against moisture as required for the appliance; - pins for ins
35、ertion into socket-outlets. Suppl y cords for single-phase port abl e appl i ances intended for direct connection to the supply mains, shall be fitted with an appropriate plug complying with AS/NZS 3112. Com pl i ance i s checked by i nspect i on. This Amendment forms part of the Standard on publica
36、tion. 29. 1Af t er Tabl e 13 Add t he f ol l owi ng Not e. Note 201 For the purposes of table 13, materials with a CTI 600 are considered to be materials that are similar to ceramic and pure mica. This Amendment forms part of the Standard on publication. 30. 2Add t he f ol l owi ng Not e t o 30. 2.
37、Note 201Alternatively, compliance may be checked as specified in 30.2 of AS/NZS 60335.1. This Amendment forms part of the Standard on publication. Annex ARepl ace t he t i t l e of “ IEC 60730 (all parts)” by “ Aut om at i c el ect r i cal cont r ol s f or househol d and si m i l ar use” . This Amen
38、dment forms part of the Standard on publication. Annex ZZ Af t er Cl ause 22. 201 i nser t t he f ol l owi ng var i at i on. 22. 202 Appliances having integrated pins for insertion into socket outlets shall comply with the requirements of AS/NZS 3112. Com pl i ance i s checked as speci f i ed i n Ap
39、pendi x J of AS/ NZS 3112. NOTE 1 Clause J.2.2.3 (Internal connections for plug portions) of AS/NZS 3112 is covered by clause 23 of this standard. NOTE 2 Clause J.2.2.6.2 (High voltage test) of AS/NZS 3112 is covered by clause 16 of this standard, except for the test of the part specified in 2.13.2
40、(e) of AS/NZS 3112. NOTE 3 Clause J.2.2.6.4 (Temperature rise test) of AS/NZS 3112 is covered by clause 11 of this standard. NOTE 4 Clause J.2.2.6.7 (Equipment with integral pins intended to be supported by the contacts of a socket-outlet) of AS/NZS 3112 is covered by clause 22.3 of this standard. T
41、his Amendment forms part of the Standard on publication. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 25. 1 Repl ace t he var i at i on f or 25. 1 by t he f ol l owi ng. In the requirement i nser t the following variation. Suppl y cords for single-phase port abl e appl i ances intended f
42、or direct connection to the supply mains, shall be fitted with an appropriate plug complying with AS/NZS 3112. This Amendment forms part of the Standard on publication. Note?201 For the purposes of table 13, materials with a CTI 600 are considered to be materials that are similar to ceramic and pure
43、 mica. This Amendment forms part of the Standard on publication. 30. 2Add t he f ol l owi ng Not e t o t he exi st i ng var i at i on. Note 201Alternatively, compliance may be checked as specified in 30.2 of AS/NZS 60335.1. This Amendment forms part of the Standard on publication. Accessed by UNIVER
44、SITY OF SOUTH AUSTRALIA on 31 May 2008 This page has been left intentionally blank. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 AS/NZS 3350.1:2002 (Incorporating Amendment Nos 1, 2, 3 and 4) Australian/New Zealand Standard Safety of household and similar electrical appliances Part 1: Ge
45、neral requirements (IEC 60335-1:1991, MOD) AS/NZS 3350.1:2002 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 31 May 2008 AS/NZS 3350.1:2002 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee EL-002, Safety of Household and Similar Electrical Appliances and Small Power
46、 Transformers. It was approved on behalf of the Council of Standards Australia on 7 May 2002 and on behalf of the Council of Standards New Zealand on 21 March 2002. This Standard was published on 13 May 2002. The following are represented on Committee EL-002: Association of Certification Bodies Aust
47、ralian Chamber of Commerce and Industry Australian Electrical and Electronic Manufacturers Association Canterbury Manufacturers Association New Zealand Consumer Electronic Suppliers Association, Australia Electrical regulatory authorities, Australia Electrical test laboratories Electrical consultant
48、s Electricity Supply Association of Australia Institution of Engineers Australia Metal Trades Industries Association of Australia Ministry of Consumer Affairs, New Zealand Keeping Standards up-to-date Standards are living documents which reflect progress in science, technology and systems. To mainta
49、in their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased. Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Web Shop at .au or Standards New Zealand web site at www.standards.co.nz and looki