《AS-1627.9-2002.pdf》由会员分享，可在线阅读，更多相关《AS-1627.9-2002.pdf（13页珍藏版）》请在三一文库上搜索。
1、AS 1627.92002 Australian Standard Metal finishingPreparation and pretreatment of surfaces Part 9: Pictorial surface preparation standards for painting steel surfaces AS 1627.9 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 This Australian Standard was prepared by Committee MT-009, Metal Fi
2、nishing. It was approved on behalf of the Council of Standards Australia on 28 February 2002 and published on 25 September 2002. The following interests are represented on Committee MT-009: Australian Institute of Metal Finishing Australian Chamber of Commerce and Industry Australian Industry Group
3、Department of Defence Galvanizers Association of Australia Institute of Materials Engineering Australia Powder Coaters Association The Royal Australian Chemical Institute Society of Automotive EngineersAustralasia Telstra Corporation Keeping Standards up-to-date Standards are living documents which
4、reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a curre
5、nt Standard, which should include any amendments which may have been published since the Standard was purchased. Detailed information about Standards can be found by visiting the Standards Australia web site at .au and looking up the relevant Standard in the on-line catalogue. Alternatively, the pri
6、nted Catalogue provides information current at 1 January each year, and the monthly magazine, The Australian Standard, has a full listing of revisions and amendments published each month. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us imme
7、diately of any apparent inaccuracies or ambiguities. Contact us via email at .au, or write to the Chief Executive, Standards Australia International Ltd, GPO Box 5420, Sydney, NSW 2001. This Standard was issued in draft form for comment as DR 02010. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 Ma
8、y 2008 AS 1627.92002 Australian Standard Metal finishingPreparation and pretreatment of surfaces Part 9: Pictorial surface preparation standards for painting steel surfaces Originated as AS 1627.91974. Second edition 1989. Third edition 2002. COPYRIGHT Standards Australia International All rights ar
9、e reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher. Published by Standards Australia International Ltd GPO Box 5420, Sydney, NSW 2001, Australia ISBN 0 7337 4412 5
10、 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 AS 1627.920022 PREFACE This Standard was prepared by Standards Australia Committee MT-009, Metal Finishing to supersede AS 1627.91989, Metal finishingPreparation and pretreatment of surfaces, Part 9: Pictorial surface preparation standards fo
11、r painting steel surfaces. The 1989 edition of this Standard endorsed as an Australian Standard, and included a copy of ISO 8501-1:1988, Preparation of steel substrates before application of paints and related products?Visual assessment of surface cleaning?Rust grades and preparation grades of uncoa
12、ted steel substrates and of steel substrates after overall removal of previous coatings. This is not the case with this edition. Rather, reference is made to ISO 8501- 1:1988, so a copy of the ISO Standard is required for the application of this Standard. Note that users of the 1989 edition of AS 16
13、27.9 may use the copy of ISO 8501-1 included with that Standard. A copy of ISO 8501-1 may be purchased from Standards Australia. This Standard is Part 9 of a series of Standards covering the preparation and pretreatment of metal surfaces used in metal finishing. The series comprises the following Pa
14、rts: AS 1627Metal finishingPreparation and pretreatment of surfaces 1627.0Part 0Method selection guide 1627.1Part 1:Removal of oil, grease and related contamination 1627.2Part 2:Power tool cleaning 1627.4Part 4:Abrasive blast cleaning 1627.5Part 5:Picking 1627.6Part 6:Chemical conversion treatment o
15、f metals 1627.9Part 9:Pictorial surface standards for painting steel surfaces Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 3AS 1627.92002 CONTENTS Page 1SCOPE4 2REFERENCE DOCUMENTS.4 3RUST GRADES5 4PREPARATION GRADES.5 5PROCEDURE FOR VISUAL ASSESSMENT FOR STEEL SUBSTRATES.5 Accessed by U
16、NIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 AS 1627.920024 ? Standards A.au STANDARDS AUSTRALIA Australian Standard Metal finishingPreparation and pretreatment of surfaces Part 9: Pictorial surface preparation standards for painting steel surfaces 1 SCOPE This Standard specifies a series of rust gra
17、des and preparation grades of steel surfaces by reference to ISO 8501-1:1988. 2 REFERENCE DOCUMENTS The following document is referred to in this Standard: ISO 8501Preparation of steel substrates before application of paint and related products?Visual assessment of surface cleanliness 8501-1Part 1:
18、Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings References to International Standards in ISO 8501-1 should be replaced by Australian Standards, as follows: Reference to International StandardAustralian Standard ISOAS
19、8501Preparation of steel substrates before application of paints and related products?Visual assessment of surface cleanliness 8501-2 Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings 8502Preparation of steel substrates before application o
20、f paints and related products?Tests for the assessment of surface cleanliness 1627 1627.1 Metal finishingPreparation and pretreatment of surfaces Part 1: Removal of oil, grease and related contamination 8503Preparation of steel substrates before application of paint and related products?Surface roug
21、hness characteristics of blast-cleaned steel substrates 8504Preparation of steel substrates before application of paint and related products?Surface preparation methods 1627Metal finishingPreparation and pretreatment of surfaces 8504-2 Part 2: Abrasive blast-cleaning1627.4 Part 4: Abrasive blast cle
22、aning 8504-3 Part 3: Hand and power tool cleaning1627.2 Part 2: Power tool cleaning Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 5AS 1627.92002 .au? Standards Australia 3 RUST GRADES Rust grades shall be designated in accordance with ISO 8501-1. 4 PREPARATION GRADES Preparation grades sh
23、all be as defined in ISO 8501-1. 5 PROCEDURE FOR VISUAL ASSESSMENT FOR STEEL SUBSTRATES The procedure is as set out in ISO 8501-1. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 AS 1627.920026 NOTES Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 7AS 1627.92002 NOTES Accessed by U
24、NIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 AS 1627.920028 NOTES Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 Standards Australia Standards Australia is an independent company, limited by guarantee, which prepares and publishes most of the voluntary technical and commercial standards use
25、d in Australia. These standards are developed through an open process of consultation and consensus, in which all interested parties are invited to participate. Through a Memorandum of Understanding with the Commonwealth government, Standards Australia is recognized as Australias peak national stand
26、ards body. Australian Standards Australian Standards are prepared by committees of experts from industry, governments, consumers and other relevant sectors. The requirements or recommendations contained in published Standards are a consensus of the views of representative interests and also take acc
27、ount of comments received from other sources. They reflect the latest scientific and industry experience. Australian Standards are kept under continuous review after publication and are updated regularly to take account of changing technology. International Involvement Standards Australia is respons
28、ible for ensuring that the Australian viewpoint is considered in the formulation of international Standards and that the latest international experience is incorporated in national Standards. This role is vital in assisting local industry to compete in international markets. Standards Australia repr
29、esents Australia at both ISO (The International Organization for Standardization) and the International Electrotechnical Commission (IEC). Electronic Standards All Australian Standards are available in electronic editions, either downloaded individually from our Web site, or via on-line and CD ROM s
30、ubscription services. For more information phone 1300 65 46 46 or visit us at .au Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 GPO Box 5420 Sydney NSW 2001 Administration Phone (02) 8206 6000 Fax (02) 8206 6001 Email .au Customer Service Phone 1300 65 46 46 Fax 1300 65 49 49 Email .au Internet .au ISBN 0 7337 4412 5Printed in Australia Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008 This page has been left intentionally blank. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 20 May 2008