《ANSI-INCITS-322-2002.pdf》由会员分享，可在线阅读，更多相关《ANSI-INCITS-322-2002.pdf（52页珍藏版）》请在三一文库上搜索。
1、ANSI INCITS 322-2002 for Information Technology Card Durability Test Methods Copyright American National Standards Institute Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/2007 20:16:10 MDTNo reproduction or networking permitted wi
2、thout license from IHS -,-,- Copyright American National Standards Institute Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/2007 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI INCITS 322-200
3、2 Revision and redesignation of ANSI NCITS 322-1998 American National Standard for Information Technology Card Durability Test Methods Secretariat Information Technology Industry Council (ITI) Approved June 10, 2002 American National Standards Institute, Inc. Copyright American National Standards In
4、stitute Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/2007 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- Approval of an American National Standard requires review by ANSI that the requirements
5、for due process, consensus, and other criteria for approval have been met by the standards developer. Consensus is established when, in the judgement of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement mea
6、ns much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made towards their resolution. The use of American National Standards is completely voluntary; their existence does not in any respect pr
7、eclude anyone, whether he has approved the standards or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. The American National Standards Institute does not develop standards and will in no circumstances give an interpretatio
8、n of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. Requests for interpretations should be addressed to the secretariat or sponsor whose name a
9、ppears on the title page of this standard. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of Amer
10、ican National Standards may receive current information on all standards by calling or writing the American National Standards Institute. American National Standard Published by American National Standards Institute, Inc. 25 West 43rd Street, New York, NY 10036 Copyright 2002 by Information Technolo
11、gy Industry Council (ITI) All rights reserved. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of ITI, 1250 Eye Street NW, Washington, DC 20005. Printed in the United States of America CAUTION: The developers
12、 of this standard have requested that holders of patents that may be required for the implementation of the standard disclose such patents to the publisher. However, neither the developers nor the publisher have undertaken a patent search in order to identify which, if any, patents may apply to this
13、 standard. As of the date of publication of this standard and following calls for the identification of patents that may be required for the implementation of the standard, no such claims have been made. No further patent search is conducted by the de- veloper or publisher in respect to any standard
14、 it processes. No representation is made or implied that licenses are not required to avoid infringement in the use of this standard. Copyright American National Standards Institute Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/20
15、07 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- i Contents Page Foreword.iii 1Scope . 1 2Normative References 1 3Default Test Environment And Conditioning. 2 4Definitions. 3 5Test Methods 5.1Delamination - 180 4 5.2Delamination - 90 7 5.3Delamination - Cross Hat
16、ch Tape Test 9 5.4ID-1 Card Flexure. 11 5.5ID-1 Card Static Stress. 14 5.6ID-1 Card Stress 1/4x1/4 23 gauge) or stainless steel welded wire cloth (#9322T5 McMaster Carr) has shown to provide proper card support. 2. A temperature and humidity controlled chamber capable of at 2C ( 4F) and 95% at 5% RH
17、 non-condensing on the card surface may be used in lieu of the sealable container and potassium sulfate solution. All other test conditions apply. 5.8.3 Procedure Prepare a saturated water solution consisting of 12.0 grams of K2SO4 per 100 grams distilled water (saturation is 12.0 grams per 100 cm 3
18、 at 25C). Pour the saturated K2SO4 solution into the bottom of the test container. The depth of the K2SO4 solution should be approximately 5 mm (approximately 0.2 in) deep. Add an additional 6 grams of K2SO4 solid per 100 grams of the saturated solution. (Some solid K2SO4 will be present in the bott
19、om of the test container.) This will ensure a saturated K2SO4 solution is present at the elevated test temperatures. Mount from up to 16 test cards that possess all desired information and features in the test card holder such that the cards are separated from each other with the card face parallel
20、to the water line. Seal the jar and place it into the laboratory oven set at 60C for a duration of 5 days, unless otherwise specified. NOTE - Duration and temperature may influence results. ALERT: The jar must remain sealed throughout the temperature exposure period. 5.8.4 Test Report Report any sig
21、n of card deterioration. Report temperature and duration of exposure. Report which card face was toward the water line. 5.8.5 Precision and Bias Test repeatability has not as yet been established for this method. Copyright American National Standards Institute Provided by IHS under license with ANSI
22、 Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/2007 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI INCITS 322-2002 20 5.9 Surface Abrasion The purpose of this test is to provide a general means to produce controlled abrasion on a
23、 card surface. 5.9.1 Significance and Use This test method shall be used for material selections and when a cards ability to resist surface abrasion is desired. Surface abrasion resistance is a function of the card materials and the application process. 5.9.2 Apparatus Abraser w/vacuum pick up or eq
24、uivalent Abrasive Wheels -2 (Taber CS -10F or equivalent) Resurfacing disks (Taber S-11 or equivalent) Dry soft cleaning cloth Hole punch or equivalent 500 gm total load per wheel (250 gm additional - no counter weight wheels) 5.9.3 Procedure Prepare two test cards that possess all desired informati
25、on and features by punching or cutting a notch on the card as shown in figure 17. Resurface the abrasive wheels for 50 cycles before testing begins and after every 250 cycles. Clean the cards and turntable thoroughly, using a dry soft cloth, to remove all debris. Avoid direct finger contact with the
26、 test cards and abrasion wheels. Mount the two test cards side by side on the turntable without any compliant pad so that the abrasive wheels pass over the desired areas. The abrasive wheels must not bounce during the test. Place the abrasive wheels on the test card and the vacuum nozzle 6,4 mm (0.2
27、5 in) above the test cards. Preset the specified number of cycles and start the abraser and vacuum. Stop the test after the specified number of cycles or until wear through of the card feature is observed. The test may be stopped after 5,000 cycles have occurred without wear through. Stopping the te
28、st cycles periodically to observe the point of wear through is recommended. 3,2 0,5 mm (0.125 0.02 in) 42,9 0,5 mm (1.689 0.02 in) 6,4 0,25 mm (0.25 0.01 in) Figure 17 - Test card notch location The abraser apparatus and abrasive wheels may be obtained from Taber Industries, 455 Bryant Street, North
29、 Tona- wanda, New York 14120. This information is given for the convenience of users of this ANSI standard and does not constitute an endorsement by ANSI or NCITS of the product named. Equivalent products may be used if they can be shown to lead to the same results. Copyright American National Stand
30、ards Institute Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/2007 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI INCITS 322-2002 21 5.9.4 Test Report Compare the wear-through of the test ca
31、rd to a control card or the number of cycles to the specified re- quirement. 5.9.5 Precision and Bias Test repeatability has not as yet been established for this method. Copyright American National Standards Institute Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka
32、/9961031100 Not for Resale, 05/08/2007 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI INCITS 322-2002 22 5.10 Bar Code Abrasion (1D) The purpose of this test is to determine the extent of 1D bar code abrasion resistance. 5.10.1 Significance and Use This test
33、method shall be used for material selections and when an evaluation of the cards barcode abra- sion resistance is desired. Barcode abrasion resistance is a function of the card materials selected and the application process. 5.10.2 Apparatus Abraser w/vacuum pick up or equivalent Abrasive Wheels -2
34、(Taber CS -10F or equivalent) Resurfacing disks (Taber S-11 or equivalent) Dry soft cleaning cloth Hole punch or equivalent 500 gm total load per wheel (250 gm additional - no counter weight wheels) Bar Code Verifier (ANSI X3.182 compliant); 0,13 mm (5 mil) aperture, 675 15 NM wand 5.10.3 Preconditi
35、on The test cards must be prepared with the 1D bar code within the location described in figure 18. 5.10.4 Procedure Measure the resulting overall ANSI Grade (A, B, C, D, or F) by averaging the grade of at least 10 scans by the verifier in the middle of the abraser path. Make a notch in the cards fo
36、r mounting the cards on the abrasers turntable as shown in figure 18. Resurface the abrasive wheels for 50 cycles before testing begins and after every 250 cycles. Clean the cards and turntable thoroughly, using a dry soft cloth, to remove all debris. Avoid direct finger contact with the test cards
37、and abrasion wheels. Mount two cards of the same construction on the turntable without any compliant pad. Place the abrasive wheels (with the additional loads) on the test card and the vacuum nozzle 6,4 mm (0.25 in) above the test cards. Preset the abraser for 50 cycles and start the abraser and vac
38、uum. The abrasive wheels must not bounce during the test. Remove the test cards and clean thoroughly using a dry soft cloth. Remeasure the ANSI grade level. If Bar code verifier is unable to produce a grade, assign a grade of F. Repeat the process of 50 Taber cycles and remeasure the ANSI grade leve
39、l until an overall grade of F is achieved for two consecutive tests. The test may be stopped after 5,000 Taber cycles have occurred without achieving two consecutive ANSI F grades. The abraser apparatus and abrasive wheels may be obtained from Taber Industries, 455 Bryant Street, North Tona- wanda,
40、New York 14120. This information is given for the convenience of users of this ANSI standard and does not constitute an endorsement by ANSI or NCITS of the product named. Equivalent products may be used if they can be shown to lead to the same results. Copyright American National Standards Institute
41、 Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/2007 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI INCITS 322-2002 23 33,5 0,5 mm (1.32 0.02 in) 6,5 0,5 mm (0.26 0.02 in) 19,0 1,0 mm (0.75
42、0.04 in) see figure 17 for location of notch Figure 18 1D Bar code test location (abrasion) NOTES 1. If the bar code is required to comply with any established standard, the compliance tests must be conducted and the results acceptable prior to this abrasion test. 2. Other symbol structures compatib
43、le with the Bar Code Verifier may be evaluated with this test method, but results should not be compared to results obtained with the standard symbol. 5.10.5 Test Report Report the starting grade and the number of abrasion cycles of each test card (to the nearest 50 cycles) that was required to achi
44、eve the second consecutive ANSI F Grade. 5.10.6 Precision and Bias Test repeatability has not as yet been established for this method. Copyright American National Standards Institute Provided by IHS under license with ANSI Licensee=USN Ship Repair Facility Yokosuka/9961031100 Not for Resale, 05/08/2
45、007 20:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI INCITS 322-2002 24 5.11 Magnetic Stripe Abrasion The purpose of this test is to determine the extent of magnetic stripe abrasion resistance. 5.11.1 Significance and Use This test method shall be used for magn
46、etic media selections and when an evaluation of the cards mag stripe abrasion resistance is desired. Magnetic stripe abrasion resistance is a function of the card materi- als selected and the application process. 5.11.2 Apparatus Abraser w/vacuum pick up or equivalent Filler card Abrasive Wheels -2
47、(Taber CS -10F or equivalent) Resurfacing disks (Taber S-11 or equivalent) 500 gm total load per wheel (250 gm additional - no counter weight wheels) Dry soft cleaning cloth Hole punch or equivalent Mag stripe read test equipment with the following characteristics: ISO/IEC 10373-2 compliant Capable
48、of reporting average signal amplitude (UA) on middle third of Track 2. 5.11.3 Procedure Prepare the test card by encoding on ISO Track 2 with a 200 ftpi 10% frequency at a recording current of Imin (See ANSI/ISO/IEC 7811-2 or -6 and ISO/IEC 10373-2 for details). NOTES 1. If the magnetic stripe material is required to comply with any established standard, the compliance tests must be conducted and the results acceptable prior to this abrasion test. 2.